Fluke HART 744 User manual

744

Documenting Process Calibrator

HARTMode Users Guide

PN 691292

December 1998

All product names are trademarks of their respective companies.

Table of Contents

Title Page

Introduction..................................................................................................................... 1

How to Contact Fluke ..................................................................................................... 2

Connecting to a HART Transmitter ................................................................................ 3

Supported vs. Generic Transmitters............................................................................... 6

Communication Operations............................................................................................ 8

Viewing Process Variables ........................................................................................ 8

Setup Operations....................................................................................................... 8

Basic ..................................................................................................................... 8

Sensor................................................................................................................... 10

Device Identification.............................................................................................. 10

HART Output ........................................................................................................ 11

HART Information................................................................................................. 11

Service Operations .................................................................................................... 12

Abort Softkey ............................................................................................................. 12

Interaction between Analog Mode and HART Mode...................................................... 12

Understanding HART Calibration................................................................................... 13

744 HART Mode Menus for Adjustment......................................................................... 13

744

HART Mode Users Guide

Calibrating a Supported HART Transmitter .................................................................... 15

Loop Test.................................................................................................................... 16

Output Trim................................................................................................................. 17

Sensor Trim................................................................................................................ 17

Cloning a Transmitter...................................................................................................... 19

Index

iii

List of Tables

Table Title Page

1. Supported vs. Non-Supported Instruments............................................................................ 7

744

HART Mode Users Guide

List of Figures

Figure Title Page

1. Connecting to a HART Transmitter........................................................................................ 5

2. 744 HART Mode Menu Tree.................................................................................................. 9

3. Block Diagram of a HART Transmitter .................................................................................. 14

744

HART Mode Users Guide

Documenting Process Calibrator HART Mode

Introduction

wWarning

To avoid electric shock, read the Safety

Information in the

744 Users Manual

before

you use the Fluke 744 Documenting Process

Calibrator.

With analog transmitters, you must make a hardware

adjustment during calibration. With HART(Highway-

Addressable Remote Transducer) transmitters,

adjustments are by remote command. These adjustments

require the use of a communication tool as well as a

calibrator. The Fluke 744, hereafter called “calibrator,”

provides communication and calibration functions in one

tool.

This manual describes how to use HART mode, which is

active when the calibrator is communicating over its serial

HART interface to a HART transmitter. Refer to the

744 Users Manual

for safety, analog mode operating

instructions, specifications, and other general information.

All of the calibrator functions described in the

744 Users

Manual

are available and can be used with HART

transmitters. The only transmitters addressed in this

manual are HART transmitters.

744

HART Mode Users Guide

How to Contact Fluke

To contact Fluke, call:

USA and Canada:

1-888-99-FLUKE (1-888-993-5853)

Europe: +31 402-678-200

Japan: +81-3-3434-0181

Singapore: +65-*-276-6196

Anywhere in the world: +1-425-356-5500

Or visit us on the World Wide Web: www.fluke.com

This manual suits for next models

Table of contents

Other Fluke Test Equipment manuals

Popular Test Equipment manuals by other brands

SMART

SMART KANAAD SBT XTREME 3G Series user manual

Agilent Technologies

Agilent Technologies BERT Serial Getting started

Agilent Technologies

Agilent Technologies N3280A user guide

Vernier

Vernier Go Direct Voltage manual

Lifeloc

Lifeloc R.A.D.A.R. quick start guide

Mercury

Mercury TSL01 user manual

MAHA

MAHA MBT Series Original operating instructions

Fuji Electric

Fuji Electric P-61 instruction manual

ETC

ETC SealerAtor user manual

Skyfine

Skyfine ETHYWAY V2 user manual

Appion

Appion G5 Twin Operation manual

PCB Piezotronics

PCB Piezotronics 8159-0112A Installation and operating manual

BW Technologies

BW Technologies MicroDock II user manual

Sun Nuclear

Sun Nuclear 1027 user guide

Biomark

Biomark HPR LITE READER user manual

Hioki

Hioki 3169-20 instruction manual

Ashcroft

Ashcroft ATE-100 operating manual

Rohde & Schwarz

Rohde & Schwarz RTA4000 user manual