Fluke 106 User manual
1
PN 4343883
June 2013
© 2013 Fluke Corporation. All rights reserved. Product specifications are subject to change without notice.
All product names are trademarks of their respective companies.
106 & 107
Digital Multimeters
Safety Information
Go to www.fluke.com to register your product, download manuals, and find more product
information.
A Warning identifies conditions and procedures that are dangerous to the user.
Warning
To prevent possible electrical shock, fire, or personal injury:
•Carefully read all instructions.
•Read all safety information before you use the Product.
•Use the Product only as specified, or the protection supplied by the Product
can be compromised.
•Do not use the Product around explosive gas, vapor, or in damp or wet
environments.
•Do not use and disable the Product if it is damaged.
106 & 107
Safety Information
2
•Do not use the Product if it operates incorrectly.
•Examine the case before you use the Product. Look for cracks or missing
plastic. Carefully look at the insulation around the terminals.
•Use only correct measurement category (CAT), voltage, and amperage rated
probes, test leads, and adapters for the measurement.
•Measure a known voltage first to make sure that the Product operates
correctly.
•Do not use test leads if they are damaged. Examine the test leads for
damaged insulation and measure a known voltage.
•Limit operation to the specified measurement category, voltage, or
amperage ratings.
•Do not apply more than the rated voltage, between the terminals or between
each terminal and earth ground.
•Do not use the HOLD function to measure unknown potentials. When HOLD
is turned on, the display does not change when a different potential is
measured.
•Do not touch voltages >30 V ac rms, 42 V ac peak, or 60 V dc.
•Do not use test leads if they are damaged. Examine the test leads for
damaged insulation, exposed metal, or if the wear indicator shows. Check
test lead continuity.
•Keep fingers behind the finger guards on the probes.
•Remove all probes, test leads, and accessories before the battery door is
opened.
Multimeters
3
•Do not exceed the Measurement Category (CAT) rating of the lowest rated
individual component of a Product, probe, or accessory.
•Remove the input signals before you clean the Product.
•Use only specified replacement parts.
•Use only specified replacement fuses.
•Have an approved technician repair the Product.
•Remove the batteries if the Product is not used for an extended period of
time, or if stored in temperatures above 50 °C. If the batteries are not
removed, battery leakage can damage the Product.
•Replace the batteries when the low battery indicator shows to prevent
incorrect measurements.
For safe operation and maintenance of the Product, repair the Product before
use if the batteries leak.
General Specifications
Maximum voltage between any Terminal and Earth Ground: 600 V
Display (LCD)................................................................... 6000 counts, updates 3/sec
Battery Type .................................................................... 2 AAA, NEDA 24A, IEC LR03
Battery Life ...................................................................... 200 hours minimum
Temperature
Operating...................................................................... 0 °C to 40 °C
Storage......................................................................... -30 °C to 60 °C
106 & 107
Safety Information
4
Relative Humidity
Operating Humidity....................................................... Non-condensing when <10°C
≤90 % at 10 °C to 30 °C; ≤75 % at 30 °C to 40 °C
Operating Humidity, 40 MΩRange............................... ≤80 % at 10 °C to 30 °C; ≤70 % at 30 °C to 40 °C
Altitude
Operating................................................................. 2000 m
Storage .................................................................... 12,000 m
Temperature Coefficient ............................................ 0.1 X (specified accuracy) /°C (<18 °C or >28 °C)
Fuse protection for current inputs ............................ 11A, 1000V Fast Fuse, Fluke specified part only
Size (HxWxL)............................................................... 142 mm x 69 mm x 28mm
Weight ......................................................................... 200 g
IP Rating...................................................................... IEC 60529: IP 40
Safety .......................................................................... IEC 61010-1: 600 V CAT III, Pollution Degree 2
Electromagnetic Environment ................................... IEC 61326-1: Portable
Electromagnetic Compatibility .................................. Applies to use in Korea only.
Class A Equipment
(Industrial Broadcasting & Communication
Equipment)[1]
[1] This product meets requirements for industrial (Class A) electromagnetic wave equipment and seller or user should take
notice of it. This equipment is intended for use in business environments and is not to be used in homes.
Multimeters
5
Table 1. Symbols
AC (Alternating Current)
Earth Ground
DC (Direct Current) Fuse
AC or DC Capacitance
Risk of Danger. Important
information. See Manual. Diode
Battery CAT II Measurement Category II is applicable to test
and measuring circuits connected directly to
utilization points (socket outlets and similar
points) of the low voltage MAINS installation.
CAT III
MEASUREMENT CATEGORY III is
applicable to test and measuring
circuits connected to the distribution
part of the building’s low-voltage
MAINS installation.
CAT IV Measurement Category IV is applicable to test
and measuring circuits connected at the source
of the building’s low voltage MAINS installation.
Conforms to relevant North
American Safety Standards. Conforms to European Union directives.
Conforms to relevant South Korean
EMC Standards Inspected and licensed by TÜV Product
Services
This product complies with the WEEE Directive (2002/96/EC) marking requirements. The affixed label
indicates that you must not discard this electrical/electronic product in domestic household waste. Product
Category: With reference to the equipment types in the WEEE Directive Annex I, this product is classed
as category 9 "Monitoring and Control Instrumentation" product. Do not dispose of this product as
unsorted municipal waste. Go to Fluke’s website for recycling information.
106 & 107
Safety Information
6
LIMITED WARRANTY AND LIMITATION OF LIABILITY
This Fluke product will be free from defects in material and workmanship for one year from the date of
purchase. This warranty does not cover fuses, disposable batteries, or damage from accident, neglect,
misuse, alteration, contamination, or abnormal conditions of operation or handling. Resellers are not
authorized to extend any other warranty on Fluke’s behalf. To obtain service during the warranty period,
contact your nearest Fluke authorized service center to obtain return authorization information, then send
the product to that Service Center with a description of the problem.
THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER WARRANTIES, SUCH AS FITNESS FOR A
PARTICULAR PURPOSE, ARE EXPRESSED OR IMPLIED. FLUKE IS NOT LIABLE FOR ANY SPECIAL,
INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES, ARISING FROM ANY CAUSE
OR THEORY. Since some states or countries do not allow the exclusion or limitation of an implied warranty
or of incidental or consequential damages, this limitation of liability may not apply to you.
Fluke Corporation
P.O. Box 9090
Everett, WA 98206-9090
U.S.A.
Fluke Europe B.V.
P.O. Box 1186
5602 BD Eindhoven
The Netherlands
11/99
Other manuals for 106
5
This manual suits for next models
1
Table of contents
Other Fluke Multimeter manuals
Fluke
Fluke LinkRunner Pro User manual
Fluke
Fluke LinkRunner Pro LRPRO-1000 User manual
Fluke
Fluke 77 Series III User manual
Fluke
Fluke 116 User manual
Fluke
Fluke 12B/18 User manual
Fluke
Fluke 187 Use and care manual
Fluke
Fluke Ti30 User manual
Fluke
Fluke 8845A User manual
Fluke
Fluke 3000 FC User manual
Fluke
Fluke 8846A Operating and maintenance manual
Fluke
Fluke 87 TRUE RMS MULTIMETER User manual
Fluke
Fluke 116 User manual
Fluke
Fluke 80 Series III User manual
Fluke
Fluke 87V Ex User manual
Fluke
Fluke 8024B User manual
Fluke
Fluke 8845A User manual
Fluke
Fluke 8050A User manual
Fluke
Fluke 27-II User manual
Fluke
Fluke 27 User manual
Fluke
Fluke i410 User manual
Popular Multimeter manuals by other brands
PeakTech
PeakTech 4000 Procedure of calibration
YOKOGAWA
YOKOGAWA 90050B user manual
Gossen MetraWatt
Gossen MetraWatt METRALINE DMM16 operating instructions
Tempo Communications
Tempo Communications MM200 instruction manual
Elenco Electronics
Elenco Electronics CM-1555 operating instructions
Mastech
Mastech MS8238C user manual
