UT8756-1 / UT8757-1
7” ANGLE SANDER / 7” ANGLE GRINDER
PLEASE READ AND FOLLOW ALL WARNINGS
Read Operating Instructions
Always become familiar with all the
instructions and warnings before
operating any power tool.
Always Wear Approved
Eye Protection
Impact resistant eye protection
should meet or exceed the
standards as set forth in the United
States ANSI Z87.1, Occupational
and Educational Eye and Face
Protection. Look for the marking
Z87.1 on your eye protection to
insure that it is an approved style.
For further information, ANSI Z87.1,
Occupational and Educational Eye
and Face Protection, is available
from the American National
Standards Institute, Inc., 11 West
42nd Street, New York, NY 10036.
Hearing Protection is
Recommended
Hearing protection should be used
when the noise level exposure
equals or exceeds an 8 hour time-
weighted average sound level of 85
dBA. Process noise, reflective
surfaces, other tools being
operated nearby, all add to the
noise level present in your work
area. If you are unable to determine
your noise level exposure, we
recommend the use of hearing
protection.
Avoid Prolonged Exposure to
Vibration
Tools can vibrate during use.
Prolonged exposure to vibration or
very repetitive hand and arm
movements, can cause injury. Stop
using any tool if discomfort, tingling
feeling or pain occurs. You should
consult your physician before
resuming use of the tool.
90 PSIG Maximum
This tool is designed to operate at
an air pressure of 90 pounds per
square inch gauge pressure (90
PSIG) maximum, at the tool. Use of
higher air pressure can, and may
cause injury. Also, the use of
higher air pressure places the
internal components under loads
and stresses they were not
designed for, causing premature
failure. The air supply should be
clean and dry, preferably
lubricated. For best results, drain
the moisture from your compressor
daily.
Universal Tool a Division of Florida Pneumatic Manufacturing Corporation
851 Jupiter Park Lane, Jupiter, Florida 33458
Toll Free 1-800-327-9403
Read these instructions carefully before attempting to install, operate
or service this Florida Pneumatic product. Failure to comply with the
instructions could result in personal injury and/or property damage!
Retain these instructions for future reference.
FPMC
WARNING:
Some dust created by power sanding,
sawing, grinding, drilling, and other
construction activities contains chemicals
known to cause cancer, birth defects or
reproductive harm. Some examples of
these chemicals are:
•Lead from lead-based paints
•Crystalline silica from bricks, cement
and other masonry products
•Arsenic and chromium from chemi-
cally treated lumber
Your risk from these exposures varies,
depending on how often you do this type
of work. To reduce your exposure to
these chemicals, work in a well-ventilated
area and work with approved safety
equipment such as those dust masks that
are specially designed to filter out
microscopic particles.
Description
Universal Tool 7" angle sander/grinder has a powerful 1 horsepower motor and is
ideal for all sanding/grinder applications. Includes a side handle for increased
operator control and rear exhaust.
devices as furnished by the manufac-
turer. Where an air tool is modified or
altered, the modifier shall provide the
safeguards to enable it to be safely used
in the operations intended and to comply
with any applicable provisions as
contained in CAGI B186.1-2009 .
Tool Installation
Pressure regulators shall be used to
limit air pressure to the rated pressure
where the supply pressure exceeds the
tool’s rated pressure. Air hoses and
lines shall be relieved of compressed
air before being disconnected or
disjointed, unless there is automatic
valve closing protection at the joint being
separated. Synthetic lubricants which
can cause deterioration of elastomer
seals shall not be used in air systems of
air tools.
Tool Maintenance
It shall be the tool owner’s and/or
employer’s responsibility to assure that
tools are maintained in a safe operating
condition. Tool maintenance and repair
shall be performed by authorized,
trained, competent personnel. Tools
shall be disconnected from their
compressed air supply before repairs
are attempted. Repairs shall be
consistent with the manufacturer’s
recommended procedures. Tool, hoses
and fittings shall be replaced if unsuit-
able for safe operation. It shall be the
tool owner’s and/or employer’s respon-
sibility to keep required rating markings
and warnings on the tool in legible
condition.
Safety Instructions
The following instructions are fur-
nished as general guidelines for use
of your pneumatic tool. They cannot
comprehensively cover all possible or
conceivable uses of the subject tool.
For additional information on the safe
use of air tools, we advise you to
obtain a copy of CAGI B186.1-2009
Safety Code for Portable Air Tools,
available from the following source:
COMPRESSEDAIR AND GAS INSTITUTE
1300 Sumner Avenue
Cleveland, OH 44115-2851
Ph: 216-241-7333
www.cagi.org OR from
Florida Pneumatic Manufacturing Corp.
851 Jupiter Park Lane
Jupiter, FL 33458
561-744-9500 www.florida-pneumatic.com
The use of the word “shall” in the
following instructions, indicates that
adherence to the particular require-
ment is necessary to conform to CAGI
B186.1-2009.
Tool Application and Usage
Portable tools shall be used only for
the purposes intended in their design
and within the capacity for which they
were intended and rated. It shall be
the tool owner’s and/or employer’s
responsibility to instruct each operator
in the safe use of the tool. Tools shall
not be used without guards and safety
