FLIR Scout User manual
431-TS00-02-QS Rev 110 June 2012
Scout Quick Start Guide
Power Button – The Scout camera has 3 power modes:
On, Off, and Standby.
• On - Takes approximately 90 seconds (during bootup there is a
fast-flashing red LED on the eyepiece display).
• Standby - After the camera is on, pressing the Power button will
toggle the camera between On and Standby mode. (In Standby
there is a slow-flashing red LED on the eyepiece display.)
• Off - Push and hold the power button for 8 sec. to turn off.
Capture Button – When enabled, takes snapshots (press and
release) or video clips (press and hold 3 seconds to start video
recording). The files are stored on the integrated SD card..
Display Brightness – Toggle through five brightness settings.
White/Black Hot/Instalert – In White Hot, hotter items appear
as white or light grey. In the Black Hot, hotter items appear as black
or dark grey. In Instalert, hot items in a scene are outlined in red.
2× Zoom – When enabled, causes the image to zoom to 2X.
Diopter Controls – The diopter adjustment knob allows a ±2
diopter range.
PowerCapture2x zoom
White hot/
Display
Black hot/
Adjustable
diopter ±2
Eyepiece
Lens cap
Brightness
Instalert
431-TS00-00-QS Scout Quick Start Guide.fm Page 1 Saturday, June 2, 2012 4:12 PM
431-TS00-02-QS Rev 110 June 2012
Installing the Batteries and SD Card
The batteries must be installed and charged before using your
camera. Install your SD card.
1. Remove the small SD card
cover.
No tools are required.
2. Install the SD card.
3. Loosen the four captive screws
securing the battery cover.
4. Pry off the battery cover by
grasping the front edge where the
SD card cover was removed.
5. Install the batteries as shown.
6. Snap the SD card cover back
into place and re-install the battery
cover—it only fits one way.
Charging the Camera
The batteries in the camera must be charged prior to their first
use.
1. Connect the Hot Shoe to your
camera.
2. Ensure that the plug is fully
seated in the Hot Shoe.
When charging correctly, the
charging indicator will be lit
yellow and will blink green for one
second within about 35 seconds.
The charging indicator will
continue to blink at decreasing
intervals until the batteries are
fully charged.
When fully charged, the charging
indicator will be lit solid green.
The initial charge time is
approximately 4 hours.
www.flir.com
Grasp SD card
Battery
cover
cover edges
and pull
+
–
+
–
–
+
–
+
Plug from power adapter
Charging
indicator
Solid
green
431-TS00-00-QS Scout Quick Start Guide.fm Page 2 Saturday, June 2, 2012 4:12 PM
Other manuals for Scout
5
Table of contents
Other FLIR Thermographic Camera manuals
FLIR
FLIR X6570sc series User manual
FLIR
FLIR ThermaCAM P20 User manual
FLIR
FLIR GFx320 User manual
FLIR
FLIR X6520sc Series User manual
FLIR
FLIR ix Series User manual
FLIR
FLIR A6000 Series User manual
FLIR
FLIR F-Series User manual
FLIR
FLIR T6 series User manual
FLIR
FLIR ThermaCAM P65 User manual
FLIR
FLIR T560-42 User manual
FLIR
FLIR Extech i5 User manual
FLIR
FLIR ETS3 Series User manual
FLIR
FLIR Exx series User manual
FLIR
FLIR ONE Series User manual
FLIR
FLIR FLIR T5 series User manual
FLIR
FLIR Navigator II User manual
FLIR
FLIR T560 User manual
FLIR
FLIR T600-NIST User manual
FLIR
FLIR ThermaCAM EX300 User manual
FLIR
FLIR FlashSight User manual
