Flex iENBL-111B User manual
iENBL-111B
OWNER’S MANUAL PN IENBL-111B DRAFT
1
OWNER’S MANUAL
iENBL-111B
2
OWNER’S MANUAL PN IENBL-111B DRAFT
OWNER’S MANUAL
CONTENTS
IMPORTANT INFORMATION 3
ABOUT IENBL DEVKIT 4
WHAT’S INCLUDED? 4
GET TO KNOW YOUR DEVKIT 5
HOW TO USE YOUR IENBL DEVKIT? 7
FAQS AND TROUBLESHOOTING 9
PRODUCT SAFETY, TIPS, AND PRECAUTIONS 10
PLACEHOLDER_ COPYRIGHTS AND OTHER NOTICES 12
iENBL-111B
OWNER’S MANUAL PN IENBL-111B DRAFT
3
OWNER’S MANUAL
IMPORTANT INFORMATION
Read these simple guidelines. Not following them may be dangerous or illegal.
COMPATIBILITY
The iENBL devkit is tested to work in multiple LoRa network operator and
gateway configurations. Please make sure your device is provisioned with a
network provider before deployment.
INTERFERENCE
All wireless devices may be susceptible to interference, which could affect
performance.
QUALIFIED SERVICE
Only qualified personnel may install or repair this product.
BATTERIES, CHARGERS, AND OTHER ACCESSORIES
Use only batteries, chargers, and other accessories approved by Flex for use
with this device. Do not connect incompatible products.
KEEP YOUR DEVICE DRY
Your device is not water-resistant. Keep it dry.
iENBL-111B
4
OWNER’S MANUAL PN IENBL-111B DRAFT
OWNER’S MANUAL
ABOUT iENBL Devkit
iENBL is a multi-sensor IoT development platform embedded in a ruggedized
clamshell enclosure with focus in LPWAN (Low Power Wide Area Network)
technologies. iENBL supports an easy to use software packages, enables developers to
develop and prototype IoT applications very quickly and smoothly
The highly integrated iENBL combines a high-performance ARM Cortex M4
microcontroller with 512 MB of memory, the sensors required for most IoT applications,
the short-range communication WiFi and BLE solutions, a few actuators and the
aforementioned LPWAN technologies.
iENBL-111B supports on unlicensed LPWAN solutions LoRa and Sigfox technologies
Figure 1- iENBL devkit dimensions: 65 mm by 97 mm by 26 mm
WHAT’S INCLUDED?
iENBL Devkit with rechargeable battery
Downloadable documentation
iENBL-111B
OWNER’S MANUAL PN IENBL-111B DRAFT
5
OWNER’S MANUAL
GET TO KNOW YOUR Devkit
Table I summarizes all the features iENBL devkit in various versions
Table I- iENBL key features
Should the IoT application need a sensor that is not included in the device, the iENBL is
expandable, and required sensors can connect to and be powered by the expansion port
(Figure 1). The expansion port is also used to program the device using a JTAG
programming interface.
The iENBL’s USB port is able to download new firmware and also charge the included
1.320 mAh rechargeable battery.
iENBL-111B
6
OWNER’S MANUAL PN IENBL-111B DRAFT
OWNER’S MANUAL
The iENBL also includes a microphone and an SD card slot for logging noise data in
predictive maintenance applications. Any of the sensors can be utilized to record data.
iENBL features a GNSS receiver which, when combined with the accelerometer, the
pressure sensor, the WiFi and BLE interfaces, and the geolocation capabilities of
LPWAN technologies, makes the iENBL an excellent platform to develop and test use
cases such as asset tracking for IoT applications. The GNSS receiver offers accurate
position information outdoors, while the LPWAN conveys rough position information in
both outdoor and indoor environments. The WiFi interface can leverage more precise
WiFi location databases, like those from Google or HERE, for indoor location
information. The BLE unit also provides an indoor location/position if a BLE beacon
infrastructure is available. The accelerometer can be employed as an energy-saving
device, updating the position information only when movement is detected. Finally, the
pressure sensor furnishes altitude information as well.
Figure 5 –iENBL Block Diagram
iENBL-111B
OWNER’S MANUAL PN IENBL-111B DRAFT
7
OWNER’S MANUAL
HOW TO USE YOUR iENBL DevKit?
Follow these instructions to start using the devkit
1. Charge the iENBL.
Charge the iENBL using a power adapter with micro-USB connection.
To charge the iENBL completely will take approximately 3 hours.
IMPORTANT: The power adapter should be specified to supply between 4.75V –
5.25V and 500mA –2100 mA
2. First start-up
The iENBL device is delivered in a dedicated shipping mode, to exit this mode
and start the device press and hold both buttons on the front of the device for
>10 seconds.
This will make the device start up for the first time and prepare it for
provisioning.
3. Steps for provisioning
Log on to your LoRa network providers website and follow their instructions to
enroll a new device using the DevEUI found on the iENBL device label.
After enrolling the device, use the generated AppEUI/JoinEUI and AppKey to
provision your iENBL device.
iENBL-111B
8
OWNER’S MANUAL PN IENBL-111B DRAFT
OWNER’S MANUAL
4. Connecting your iENBL to a Computer (With Extension Board)
Connect the extension board to the iENBL device as shown below.
Connect the ST-Link to the USB port of the computer being used and to the 20-
pin connector on the extension board labeled “Program”.
iENBL-111B
OWNER’S MANUAL PN IENBL-111B DRAFT
9
OWNER’S MANUAL
FAQs AND TROUBLESHOOTING
Q: What’s the operating temperature?
A: 5C to +35C
Q: Is iENBL water resistant or water proof?
A: No. iENBL includes a ruggedized clamshell casing
Q: How long does it take to fully charge iENBL?
A: Approximately 3 hours. For safety reasons charging will be automatically terminated
after approximately 6 hours even if the battery is not fully charged at that time.
Q: Is the battery removeable?
A: No, please do not use sharp objects to remove the battery.
Q: How can I use a sensor that is not included in iENBL?
A: Additional sensor can be used with the iENBL by connecting them to the external
expansion interface. The simplest way to do this is by using a sensor expansion board
that can be acquired though your Flex contact person.
Q: What’s the operating temperature?
A: 5C to +35C
Q: What are the supported development environments for iENBL?
A: Atollic True Studio and Keil uVision
Q: Where do I call for support?
A: TBD
iENBL-111B
10
OWNER’S MANUAL PN IENBL-111B DRAFT
OWNER’S MANUAL
PRODUCT SAFETY, TIPS, AND PRECAUTIONS
How to take care of iENBL.
Handle the iENBL, charger and accessories with care.
The following suggestions will help you keep iENBL operational.
Keep the iENBL dry. Precipitation, humidity, and all types of liquids or moisture can
contain minerals that corrode electronic circuits. If iENBL gets wet, let it dry.
WARNING: Failure to follow these safety instructions could result in fire, electric shock,
injury, or damage to phone or other property. Read all the safety information below
before using iENBL.
Battery charging tips and precautions
Charge the battery before using it for the first time or when it has been unused for
extended periods.
If the battery is completely discharged, the device cannot be turned on immediately
after the charger is connected. Allow the depleted battery to charge for several minutes
before turning on the device.
Using a power source other than a USB power adaptor, such as a computer, may result
in a longer charging time or not charging at all due to a lower electric current.
While charging, the device and the charger may heat up. This is normal and should not
affect the device’s lifespan or performance. If the battery gets hotter than usual, the
charger may stop charging.
Battery
Don’t attempt to replace the iENBL battery yourself—you may damage the battery,
which could cause overheating and injury.
Using damaged cables or wall adapters, or charging when moisture is present, can
cause fire, electric shock, injury, or damage to the phone or other property. Make sure
the USB cable is fully inserted into the power adapter before plugging the adapter into
a power outlet.
Storage
Do not use or store the iENBL in dusty or dirty areas as it will affect its performance.
Table of contents
Popular Microcontroller manuals by other brands
AMS
AMS AS7261 Demo Kit user guide
Novatek
Novatek NT6861 manual
Espressif Systems
Espressif Systems ESP8266 SDK AT Instruction Set
Nuvoton
Nuvoton ISD61S00 ChipCorder Design guide
STMicrolectronics
STMicrolectronics ST7 Assembler Linker user manual
Texas Instruments
Texas Instruments Chipcon CC2420DK user manual
Texas Instruments
Texas Instruments TMS320F2837 D Series Workshop Guide and Lab Manual
CYPRES
CYPRES CY14NVSRAMKIT-001 user guide
Texas Instruments
Texas Instruments INA-DUAL-2AMP-EVM user guide
Espressif Systems
Espressif Systems ESP8266EX Programming guide
Abov
Abov AC33M8128L user manual
Laird
Laird BL654PA user guide