Flamerite Fires Jaeger User manual

Page 1 of 3

Jaeger

This product is only suitable for well insulated spaces or occasional use

Installation & Precautions

Carefully remove the suite from the packing, checking that neither the heater nor the power cable has been damaged during transport. Do not

operate the suite if either is damaged. Please bear in mind the weight of the suite before removal from the packaging and installation. Consider if

help is required. Any alteration to the power cable should only be done by a qualified electrician and to the Flamerite Fires guidelines stated

below. Your suite is guaranteed for one year from the date of purchase. In the unlikely event of a breakdown you have access to our customer

services team, simply call 01543 251122 during office hours, 9am – 5pm or e-mail on info@flameritefires.com The accessories are found in a box

that is packed at the side of the suite.

INSTALLATION

Where a chimney is not blocked off completely it will cause the heater to cut out during use. ONLY if installing into a chimney and you are not

sure that you have cut off the draw 100% we recommend covering the slots in the rear and at either side.

Automatic safety cut out: The heater is fitted with an automatic cut out to prevent any damage due to overheating. The element will continually

and automatically cut out if the airflow is obstructed. Never cover the air outlets. To reset, switch the fire off, disconnect from the mains supply,

remove the cause of the overheating, check the micro switches and allow to cool for a suitable period then switch the fire back on. Caution: In

order to avoid a hazard due to inadvertent resetting of the thermal cut out, the appliance must not be supplied through an external switching

device, such as a timer, or connected to circuit regularly switched on and off by a utility.

Electrical connections: Your appliance comes fitted with a plug that incorporates a 13A fuse. The replacement fuses must be 13A and ASTA

approved. If the fuse cover is lost the plug must not be used until a replacement cover, of the same colour, is obtained from an electrical retailer.

The appliance is fitted with a moulded plug if it is necessary cut off the plug, for any reason, it must be discarded immediately with the fuse

removed. Under no circumstances should any attempt be made to reuse the plug, do not insert into any 13A socket as this could cause a hazard. If

the mains cable is damaged it must be replaced by the manufacturer or an authorised technical service centre.

WARNING THIS APPLIANCE MUST BE EARTHED

IMPORTANT

The wires in the mains lead are coloured in accordance with the following code.

Green and yellow:

EARTH

Blue:

NEUTRAL

Red:

LIVE

As the colours of the wires in the mains lead of this appliance may not correspond with the colour markings in your plug proceed as follows: -

•The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter E, or

coloured green or coloured green and yellow, or marked with the earth symbol

•The wire which is coloured blue must be connected to the terminal in the plug which is marked with the letter N, or coloured

black.

•The wire which is coloured brown must be connected to the terminal in the plug which is marked with the letter L, or coloured

red.

Insert the plug tightly into its IEC connector underneath the fire if not already done so. If the removal of the plug is absolutely necessary for

installation, cut off in an area within 100mm only of the plug itself. Any further will affect your warranty.

Page 2 of 3

Using as a Hang on the Wall.

The height at which you may wish to fix the fire to the wall is up to you, though we recommend anywhere from 40-60cm from the floor to the

bottom of the fire. The wall bracket should be fixed to the wall with the highest point of the edge facing forward/upward Fig.1.The corresponding

edge where the fire is to be hung on the wall bracket can be found on the back, at the top, across the fires centre. Once the wall bracket has been

fixed, lift and hook the fire into place. A second bar should then be added to the underside of the fire Fig.2. A channel in the underside of the fire

will be visible, the remaining bracket will slot into this. Again mark off, remove fire and fit the bracket to the wall. Refit the fire, lift and hook onto

the brackets.

Fig. 1 Fig. 2

Fuel Effects

Once the fire has been installed in the correct position unpack the fuel effect from the accessory box. Pebbles (and wood effect/cost

option) maybe arranged in a random formation on top of the fuel bed.

External lighting Remote Control (RGB)

•These lights maybe turned on or off independently from the fire by pressing the buttons marked ON & OFF on the remote

control.

•For the RGB remote to be affective it must be pointed at and upwards towards the top where the RGB lamps are situated. The

working area is in a direct line of sight at the very front of the suite toward the lights. You may, depending on where the remote

is pointed change one lamp at a time or both together.

•There are sixteen individual colours to choose from as well as the ability to mix and match using the pre-set or programmable

fade and strobe functions. A dimmer is also present.

Page 3 of 3

MAINTENANCE

Before any maintenance/cleaning is undertaken, always disconnect the fire from the mains power supply.

Replacing Lamps (Dimmable 240V 7W 3000k E14 LED lamps): Replacements are available from Flamerite Fires info@flameritefires.com

Allow a suitable time for the lamps to cool then remove the glass & fuel effect (see Installation). Remove the two screws from either side of the

fuel bed and lift out of place. Remove and replace the lamps, fuel bed, fuel effect and glass. Please note that replacement Lamps are only covered

from purchase by a 2 year warranty

Cleaning

The fire can be cleaned with a soft damp cloth and none abrasive glass cleaner.

WARNINGS

•Do not open and close the glass repeatedly while the heater is on or the cut out will activate.

•Do not use the fire in the vicinity of a bath shower or swimming pool.

•Never use the fire to dry laundry.

•Never install the fire directly underneath a fixed main socket.

•Never cover the appliance during the operation of the fire.

•The use of an extension lead is not recommended.

•Particular caution should be applied to ensure that children do not play with the fuel effects.

•As with any electrical appliance whilst the instructions aim to cover as many eventualities as possible, caution and common sense should

be applied when operating your appliance, particularly in the vicinity of small children.

Areas around the fire will become hot when activated. We strongly recommend small children be kept away from having any direct

contact with the appliance by means of fitting a fireguard. This appliance is not intended for use by persons (or children) with reduced

physical sensory or mental capabilities or lack of experience or knowledge unless they have been given supervision or instruction

concerning the use of the appliance by the person responsible for their safety. Children should be supervised to ensure they do not

play with this appliance.

PROBLEM SOLVING

•No power to the fire: Check the wall socket, plug, fuse and lamps.

•No illumination: Make sure fire is turned on. Check heater is working, if so check lamps.

•Illumination but heater blowing cold: The safety cut out may have operated. Check for obstruction around the heater. If installed into a

chimney or cavity wall is 100% of drawn air blocked off from the fire.

•Noise when illuminated: Due to moving parts, the electric fire will make a noise.

•Noise from the heater when in use: The sound of rushing air is normal.

RECYCLING

Please recycle responsibly. Take your item to your local recycling centre – you can easily locate your nearest centre on the Recycle Now website or

check with your retailer for details on either a collection service or a store take-back scheme (some may apply charges). Councils may offer a

household recycling collection service for small electrical items; contact your local authority for more details.

Information requirement for electric local space heaters

Model identifier (s)

Jaeger

Item

Symbol

Value

Unit

Heat output

Nominal heat output

Pnom

2.0

Minimum heat output (indicative)

Pmin

1.0

Maximum continuous heat output

Pmax,c

2.0

Auxiliary electricity consumption

At nominal heat

elmax

28.5

At minimum heat

elmin

28.5

In standby

elSB

0.0015

Type of heat output/room temperature control

With distance control option

Room temperature control, with open window detection

With electronic room temperature control plus week timer

Yes

Contact details:

Flamerite Fires Ltd. Greenhough Road, Lichfield. Staffs.

WS13 7AU

Table of contents

Other Flamerite Fires Indoor Fireplace manuals

Flamerite Fires

Flamerite Fires Corello F01 User manual

Flamerite Fires

Flamerite Fires Cisco User manual

Flamerite Fires

Flamerite Fires Corello User manual

Flamerite Fires

Flamerite Fires Corello User manual

Flamerite Fires

Flamerite Fires OnmiGlide 1300 User manual

Flamerite Fires

Flamerite Fires OMNIGLIDE Glazer 900 User manual

Flamerite Fires

Flamerite Fires Glazer 600 User manual

Flamerite Fires

Flamerite Fires Sonata-2 User manual

Flamerite Fires

Flamerite Fires Lazio User manual

Flamerite Fires

Flamerite Fires Gotham Series User manual

Flamerite Fires

Flamerite Fires Essence Corello User manual

Flamerite Fires

Flamerite Fires Stanford User manual

Flamerite Fires

Flamerite Fires Kelvin User manual

Flamerite Fires

Flamerite Fires E-FX User manual

Flamerite Fires

Flamerite Fires Valiant User manual

Flamerite Fires

Flamerite Fires E-FX 1000 User manual

Flamerite Fires

Flamerite Fires 400 Series User manual

Flamerite Fires

Flamerite Fires E-FX SL User manual

Flamerite Fires

Flamerite Fires Essence Gotham 600 User manual

Flamerite Fires

Flamerite Fires Luma Series User manual

Flamerite Fires

Flamerite Fires Cisco Extreme User manual

Flamerite Fires

Flamerite Fires Arlo 400 Series User manual

Flamerite Fires

Flamerite Fires E-FX User manual

Flamerite Fires

Flamerite Fires essence Voyager User manual

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Desa

Desa CCFPDFT Owner's operating & installation manual