Firesense 2117 User manual

Owner’s Manual

Models: 02117/60694/02678

READ & SAVE these instructions

Carefully read and review before attempting to

assemble, install, operate, or maintain this product.

Observe all safety instructions and information.

FAILURE TO FOLLOW WARNINGSAND

OPERATIONALINSTRUCTIONS

CONTAINED IN THIS MANUAL CAN

RESULT IN SEVERE PROPERTY DAMAGE

AND OR PERSONAL INJURY.

***For Residential Use Only***

***Important Notice***

Do not return to place of purchase!!

Please contact our Toll Free Hotline at

1-866-985-7877 for customer

service and warranty issues.

SAVE THESE INSTRUCTIONS

Distributed by:

Well Traveled Living

Amelia Island, FL 32034

Web: www.wtliving.com

Email: [email protected]

Safety Guidelines

Read this manual carefully to become knowledgeable about your heater and how to use it properly.

To help recognize this information, observe the following symbols.

Indicates a potentially hazardous situation which, if

not avoided, WILL result in serious injury or death.

Indicates a potentially hazardous situation, if not

avoided, COULD result in serious injury or death.

Indicates a potentially hazardous situation which, if

not avoided, MAY cause moderate injury or damage to

the equipment.

Indicates important information that if not followed,

may cause damage to the equipment.

. Risk of Fire. There is always a risk of fire when working with a heater. Keep it away from

flammable liquids and any material that could easily catch fire.

2. Risk of Fire. If the heater falls, this unit might start a fire.

3. Hot or Burn Hazard. This unit may be hot at any time during its use especially around the head

and heating element.

4. Electrical Hazard. Disconnect all electric power before working on the unit. There is a chance

of electric shock if you work on this unit with it still plugged into the wall.

5. Electric Shock. This unit uses electricity to operate. Do not use this heater around water or if the

cord has been damaged.

•Improper treatment of the heater can damage it and also shorten its life span.

•To prevent electrical shock follow electrical plug requirements on page 9 of this manual.

This appliance MUST be grounded.

* When using outdoors, we recommend using a certified GFI (Ground Fault Interrupt)

outlet to protect against electrical shock.

* All installations must be in accordance with I.E.E. safety regulations or the equivalent.

* Avoid the use of an extension cord with this appliance.

* Do not place any objects such as furniture, papers, clothing or curtains closer than 3 feet

to the front and sides of the heater.

PARTS LIST

1- IR Head unit w/Protective Shield with:

* Pre-installed Tilt Switch (safety cut off)

* On/Off Switch (PULL for ON, PUSH for OFF)

* Angle Adjustment Bar

* 1500 Watt quartz halogen bulb

* Swivel Bracket

* 12 foot, 16/3 grounded electrical cord

2 – Mounting Bracket – attaches head unit to telescopic pole

3 – Curved Upper Arm

4 – Inner support tube section for telescopic body

5 – Telescopic Body – adjustable

6 – Base connection pole section

7 – Support Collar w/Flange for Telescopic Body

8 – Base Assembly w/wheels

9– Protective vinyl cover for head unit

10 – Hardware packet—19 threaded bolts;

2 small threaded screws w/flat

washers;

1 – ¾” nut w/flat washer and lock

washer.

CAUTION!

ImportantInstructions

1. Read all instructions before using this heater.

2. This heater is hot when in use. To avoid burns,

do not let bare skin touch hot surfaces. Keep

combustible materials, such as furniture,

pillows, bedding, papers cloths, and curtains at

least 3 feet (0.9m) from the front, sides and

rear of the heater.

3. DO NOT leave heater unattended. Extreme

caution is necessary when any heater is used

by, or near, children or disabled persons, and

whenever the heater is left operating and

unattended.

4. Always unplug heater when not in use.

5. Do not operate any heater with a damaged cord

or plug, if the heater malfunctions, or has been

dropped or damaged in any manner. Return

heater to authorized service facility for repair.

6. Can be used indoors or outdoors. Operate 3

feet (0.9m) from people or objects.

7. Never operate heater near water or where it

can be knocked over.

8. Do not run cord under carpeting. Do not cover

cord with throw rugs, runners, or similar

coverings. Arrange cord away from traffic area

and where it will not be tripped over.

9. To disconnect heater, switch to OFF position

(push in switch located on head unit) and then

remove plug from electrical outlet.

10. Connect to properly grounded outlets only.

11. Do not insert or allow foreign objects to enter

any ventilation or exhaust opening; doing so may

cause an electrical shock or fire, or may damage the

heater.

12. To prevent a possible fire, do not block air

intakes or exhaust in any manner. Do not use on

soft surfaces, like a bed, where openings may

become blocked.

13. A heater has hot and sparking parts inside. Do

not use it in areas where gasoline, paint, or

flammable liquids are used or stored.

14. Use this heater only as described in this manual.

Any other use not recommended by the

manufacturer may cause fire, electrical shock,

or injury to persons.

15. Avoid the use of an extension cord because the

extension cord may overheat and cause a risk

of fire. However, if you must use an extension

cord, use either a 12 gauge or 14 gauge wire

which is rated not less than 1900 watts. The

recommended length for a 14 gauge is 0-50

feet but if you must use a longer cord, use a 12

gauge NO LONGER than 100 feet.

16. This unit comes equipped with a Safety Tilt

Switch mechanism. Power will shut off

automatically should the unit be accidentally

knocked over or tilted past 15 degrees. To

reset, unplug the unit from wall outlet,

reposition on a flat, level surface and plug in

again.

17. SAVE THESE INSTRUCTIONS for future

reference.

Assembling Your Heater

Before beginning assembly, be sure to read and familiarize yourself with the overall assembly process and

instructions in this manual. It may be helpful to have someone assist you with the assembly. You will need the

following tools (NOT INCLUDED):

** #2 or #3 Philips Screwdriver (or standard slotted screwdriver)

** Adjustable Wrench.

Make sure you complete assembly on a clean, level, preferably carpeted location. A flat piece of cardboard will also

work for assembly. Unpack and identify all components listed on page 3 of this manual and lay them out on the

carpeted floor or piece of cardboard and then follow the steps below:

STEP 1

Loosen and remove the top 2 screws on each side of the head unit (Part 1) and attach the angle adjustment handle

(included with Part 1) as shown in Figure 1.

Tighten the screws as shown in Figure 2.

FIGURE 1

FIGURE 2

STEP 2

Using mounting bracket (Part 2), thread entire electrical cord through the mounting bracket as shown in Figure 3.

STEP 3

Using 4 threaded bolts, attach mounting bracket (Part 2) to head unit (Part 1) as shown in Figure 4.

STEP 4

Align tilt switch (black box on head unit, Part 1) to threaded holes on mounting bracket (Part 2) and insert small

screws with flat washers as shown in Figure 5.

FIGURE 3

FIGURE 4

FIGURE 5

STEP 5

Thread electrical cord through curved upper arm (Part 3) and attach with 4 threaded bolts as shown in Figure 6.

STEP 6

Insert inner support tube (Part 4) inside telescopic body (Part 5) as shown in Figure 7. Tighten clamp collar as shown

in Figure 8.

STEP 7

Thread electrical cord through inner support tube and telescopic body as shown in Figure 9 and affix curved upper

arm and inner support tube with one threaded bolt as shown in Figure 10.

FIGURE 6

FIGURE 8

FIGURE 7

FIGURE 9

FIGURE 10

STEP 8

Thread electrical cord through base connection pole section (Part 6) and insert 4 threaded bolts as shown in Figure11,

12 and 13.

STEP 9

Mount support collar flange (Part 7) to base assembly with wheels (Part 8) as shown in Figure 14, and secure with

flat washer, lock washer, and ¾” bolt as shown in Figure 15.

STEP 10

Carefully lift pole and head unit assembly and insert lower end of pole into support collar flange (Part 7) as shown in

Figure 16. Secure with 6 threaded bolts.

FIGURE 12

FIGURE 11

FIGURE 13

FIGURE 14 FIGURE 15

FIGURE 16

OPERATING INSTRUCTIONS

This appliance MUST be grounded.

* When using outdoors, we recommend using a certified GFI (Ground Fault Interrupt) outlet to protect

against electrical shock.

* ALL installations must be in accordance with I.E.E. safety regulations or equivalent.

* Avoid the use of an extension cord with this appliance. If one is used, it must meet the requirements

as outlined in #15, “Important Instructions” on page 4 of this manual.

* Do not place any objects such as furniture, papers, clothing, or curtains closer than 3 feet to the front,

top or sides of this heater.

* ALWAYS unplug the heater when it is not in use.

For optimal performance and safety concerns, we HIGHLY recommend that the Infrared Heating

System be operated at a minimum of 98” in height or the maximum extended length of the telescopic

body sections. You should only lower the height of the unit for storage purposes when it has

completely cooled and is not in operation.

To adjust the IR telescopic body:

Pull up on the release levers of the tightening clamps and adjust tension using

the tension knobs. Raise and lower the telescopic sections and/or swivel

to desired position and then push in clamp levers to secure. DO NOT

over tighten tension knobs. There should only be a moderate amount

of tension to maintain the telescopic position of your heater.

Step 1

Before turning on your Infrared Heating System, check to make sure the “On/Off” switch located on

the tilt switch (black box) of the head unit is pulled OUT or in the ON position (note: to turn the heater

“Off”, push in the switch). Next, extend all 3 telescopic sections to their maximum extended length.

Release clamp levers and pull up on each of the sectional steel tubes until each tube stops. Then push

in clamp levers to secure sections in place. Adjust the tension knobs as needed to maintain height

position.

Step 2

The Infrared Heating System comes equipped with a heavy duty, 16/3 gauge wire

and grounded plug. This appliance must be used with an outlet that has been installed

and grounded in accordance with local codes and ordinances. Make sure the heater is

connected to an outlet having the same configuration as shown in the figure shown to

the right. DO NOT use an adapter with this product. Check with a licensed electrician if

the grounding instructions are not understood completely or if the wall outlet does not

match the plug.

Step 3

Your Mojave Sun, Infrared Heating System is ready to enjoy. Plug the appliance in and enjoy the

warmth!

CAUTION!

Specifications

Model: 02117/60694/02678

Voltage: 120 volts

Amps: 12.5 amps

Wattage: 1500 watts

Lamp Type: Quartz Halogen

Minimum Operational Height: 8 ft., 2 in. (98 in.)

Assembled Weight: 53 lbs.

Head Unit Dimensions: 4.5” x 7” x 22”

Heater Assembled Dimensions: 22” diameter base, 98” height

Storage

*Always UNPLUG the unit when not in use.

* Once the head unit has completely cooled, store the heater with the protective vinyl cover on the

head unit.

* When heater is not in use for an extended period of time, store in a covered location that is dry and

out of the weather. Make sure the heater is stored in a location that is out of the way of people and pets

that may accidentally knock the heater over or damage the appliance. Before storing the heater, make

sure the electrical cord is coiled and out of the way.

* When storing, ALWAYS lower the telescopic pole to its lowest level. This will make it easier to

store and reduce the risk of any accidental tipping over of the heater.

Maintenance

Your Infrared Heating System is virtually maintenance free! A minute to wipe down exposed surfaces

is all it takes to maintain your heater.

* Head unit and shield: Use a non-abrasive cleaner and a soft cloth to wipe off debris and dirt from the

exposed surfaces. NEVER spray liquids or cleaners into the housing area where the halogen lamp

is located. Do not try to disassemble of clean the inner cavity where the halogen lamp is located. For

any maintenance on the head unit, please call the toll free customer service hotline.

* Telescopic pole and curved arm components: These can easily be wiped clean using a non-abrasive

cleaner and a soft cloth.

* Base with wheel assembly: Use non-abrasive cleaner and a soft cloth. Any scratches, chips or rust

spots can be touched up using an exterior matte finish black paint.

Other manuals for 2117

This manual suits for next models

Table of contents

Other Firesense Patio Heater manuals

Firesense

Firesense FireSense PH08-S User manual

Firesense

Firesense 60403 User manual

Firesense

Firesense 2110 User manual

Firesense

Firesense 60788 User manual

Firesense

Firesense Patio Heater User manual

Firesense

Firesense LIP-10A-TGG User manual

Firesense

Firesense PH08-SA User manual

Firesense

Firesense LIP-10A-TGG/60951 User manual

Firesense

Firesense DLX 46K User manual

Firesense

Firesense 1902415 Quickspecs

Firesense

Firesense FireSense 01775 User manual

Firesense

Firesense Pro Series User manual

Firesense

Firesense KLD7001S User manual

Firesense

Firesense FireSense 02411 User manual

Firesense

Firesense PH01-SS User manual

Firesense

Firesense FireSense 60763 User manual

Firesense

Firesense LIP-10A-TGG-LPG-BU User manual

Firesense

Firesense 11201 Deluxe User manual

Firesense

Firesense Garden & Patio 60368 User manual

Firesense

Firesense LIP-10-TGG A2 LED 60951 User guide

Firesense

Firesense 61279 User manual

Firesense

Firesense 60402 User manual

Firesense

Firesense 2127168 Quickspecs

Firesense

Firesense Steel Pagoda User manual

Popular Patio Heater manuals by other brands

empasa

empasa HMXD-E-NHS operating instructions

Sunred

Sunred Indus manual

HEAT1

HEAT1 ECO pro-line 2300W instructions

Heatmaxx

Heatmaxx SRPH98 instruction manual

Sunjoy

Sunjoy A30600640 manual

Event Furniture

Event Furniture 16091 Operating & safety guide

Prem-I-Air

Prem-I-Air EH1462 manual

Blumfeldt

Blumfeldt 10028637 manual

Sunjoy

Sunjoy L-PH011PSS-2 owner's manual

Melissa

Melissa 670-202 user guide

Quality Heating

Quality Heating THE-12DW manual

DCS

DCS PHFS-P4 Use and care and installation guide

EUROM

EUROM 334241 instruction manual

Lava Heat

Lava Heat Venetian owner's manual

EHS Ltd.

EHS Ltd. HQH-2000W instruction manual

VONROC

VONROC ALICUDI PH515AC Original instructions

OZONA

OZONA Heatflow IF010997 Safety instructions and operation manual

theBBQshop

theBBQshop 51611010 Safety, Installation, Operation and Maintenance