Firebelly FB1 Gas User guide

Installation and Servicing Instructions

FB1 Gas

GB/IE

Unit 16, Upper Mills, Canalside, Slaithwaite, Huddersfield, HD7 5HA, UK

1 Technical Information

Gas

Natural Gas G20

Natural Gas G25

LPG G30/G31

Category

I2H

I2L

I3+

Heat Input Max(Net)

6.28kw

5.92kw

5.82kw

Heat Input Min(Net)

2.24kw

2.14kw

2.22kw

Supply pressure

20 mbar

25 mbar

30/37 mbar

Injector Size

82/440

92/190

Setting Pressure Max

16.8 mbar

21.5 mbar

28.0/36.5 mbar

Setting Pressure Min

2.3 mbar

3.0 mbar

4.2/6.0 mbar

Oxypilot - Seagas

P441

P412D

P451

Gas Consumption

0.67m3/h

0.73m3/h

0.179m3/h

NoX Class

Efficiency class

Countries

AT, CH, DK,

ES, FI, GB, IE,

IT, PT, SE

BE, CH, ES, FR,

GB, IE, IT, PT

Gas Connection

8mm Tube

2 Important Notes

This stove is a fuel effect radiant convector. Before installation

ensure that the local distribution conditions (identification of the

type of gas and pressure) and the adjustment of the appliance are

compatible.

The data label is located behind the controls cover.

The installation must be in accordance with these

Instructions and National Regulations and must

be carried out by a qualified installer.

Any flue damper plate or flue restrictor must be

removed or fixed permanently in the fully open

position, or shall only be fitted in accordance with

National Regulations.

If the chimney has previously been used to burn

solid fuel, the chimney should be swept before the

stove is installed.

Before the stove is installed a flue test in accordance

with National Regulations should be carried out.

The gas connection must be in accordance with

National Regulations.

The stove is fitted with a spillage combustion monitoring safety

device (O.D.S). This system is not

adjustable, and must not be put out of action.

If any parts of the spillage monitoring system

require replacement only original manufacturers

parts must be used.

All surfaces except the control cover plate and the controls

themselves are considered to be working surfaces.

When operating on Natural Gas the stove is intended for use on a

gas installation with a governed meter.

3 Dimensions

4. Installation

Install the stove in accordance with the

requirements given below. If a concealed gas

connection is to be made prepare the pipework

prior to installing the stove.

(i) SITING THE STOVE

The stove can be installed in any adequate area

suitable for solid fuel fires and stoves.

Clearances from non-combustible material in the

fireplace opening must be at least 50mm on the

left side, 50mm on the right hand side and

50mm at the back. These distances must be

extended to a minimum clearance of 500mm

from any combustible material.

(ii)Hearth

The stove must stand on a fireproof hearth made

of non-combustible material of minimum

thickness 12mm and be of sufficient size to

accommodate the stove. (See Fig 1).

(iii)Fire Surround & Shelves

It is recommended that a fire surround should not

be closer than 500mm from the stove, if

manufactured from a combustible material.

A combustible shelf may be fitted provided that it

is not more than 150mm deep and there is at least

500mm clearance from the top of the stove. Curtains and other soft

furnishing must be at least 500mm away from the top of the stove.

(iv) FLUE CONNECTION

The flue should be at least 3m high and at least

125mm diameter or equivalent area.

Horizontal or negative gradients in the flue pipe

should be avoided.

It is recommended that a minimum height of

500mm from the stove should be established

before any significant change in the direction of

the flue.

(v) VENTILATION

Ventilation should be in accordance with National

Regulations. In the United Kingdom purpose

provided ventilation is not normally required, except in new build

houses.

(vi) GAS CONNECTION

The gas supply connection is behind the controls cover plate, left

hand side of the gas valve.

A nut and olive (strapped to the valve body), is supplied with the

stove.

The gas supply should incorporate a service tap,

be purged and any loose matter removed.

Connect the gas supply pipe and check for gas

soundness.

5 positioning of the logs

Slacken the Allen screw using an Allen key securing the stove

door and open the door (as shown below)

Close the stove door and secure with an Allen key. Under no

circumstances should the stove be operated with the door open,

without the door attached or the glass damaged.

6 Commissioning the stove

When lighting the pilot follow these instructions exactly.

Lighting instructions

Should the stove be extinguished for any reason

wait 3 minutes before re-ignition is attempted. Slacken the rear

pressure test sealing screw on the left hand side of the gas valve

(fig 6) and connect a suitable pressure gauge to the pressure

test point.

(i) Lighting The Pilot

Turn knob A (fig 6) counter clockwise towards the ignition

position (IGN) until reaching stop, press down and hold for five

seconds (only pilot gas flows).

Continue pressing down knob A while turning further counter

clockwise to activate piezo, continue to hold down for ten seconds

after pilot burner has been lit. If pilot does not light, steps 1 and 2

can be repeated immediately. Upon lighting, release knob and turn

further counter clockwise to ON position. Pilot gas flows and main

gas flows in accordance to the temperature setting of knob B.

(ii)High Setting

If the pilot is not already lit, light the pilot as described in (i)

Turn knob B anti clockwise until the high setting is reached.

Check the setting pressure is in accordance with that given in the

technical information setting adjust if necessary. (fig 6)

(iii) Low setting

Turn knob B clockwise to low setting (just before flame is

extinguished). Check that the setting pressure is in accordance with

that given in the technical section.

Adjusting the flame Height (fig 6)

To turn the stove on and/or to increase the flame

height, press the ▲ button and the small button A at the same time

on the remote handset. Continue pressing until the desired

flame height is obtained. Press and hold the ▼

button to reverse the procedure.

The receiver is equipped with a built-in delay,

recognisable by the flickering light, to facilitate

fine adjustment of the flame. The motorised valve

is equipped with a slip clutch, allowing manual

adjustment of main gas by turning knob B.

To Turn Off Gas to Stove

Turn knob A clockwise until reaching stop. In

this position only pilot gas flows. To shut off the

valve completely, press down slightly and

continue to turn clockwise from pilot position to

the OFF position. The safety interlock prevents

re-ignition of the pilot flame until the

thermocouple has cooled down sufficiently

(elapsed time will vary based on thermocouple

type). Switching off the remote is not necessary.

Disconnect the pressure gauge, tighten the test point sealing screw

and test for gas soundness.

Handset Information

Note : Mains electrical power is not required as this system runs

on batteries only. (Alkaline recommended)

Handset 1 x 9V block

Receiver 4 x 1.5v AA

Figure 6 Control Valve and transmitter

Note

It is recommended to turn the combination control either to the off

or pilot position if the appliance is left unattended for long periods

(eg away on holiday), so that it cannot receive commands from the

remote transmitter. Exercise caution when leaving the appliance

unattended, in exceptional cases sound waves from sources other

than that of the transmitter can cause flame height adjustment. For

the handset to function correctly, the transmitter must remain

within the range of the receiver. The transmitter should not be used

in very close proximity of the receiver (less than 1 metre/3 ft) as

this could, in very rare cases produce an electronic switching error.

This could block the motor when the knob reaches the end.

7 Check for spillage

Close all doors and windows in the room containing the appliance.

Light the stove and turn the control knob to ‘HIGH’. Leave the

appliance for 5 minutes.

Apply a smoke match along the bottom edge of the draught

diverter. The installation is satisfactory if the smoke is drawn into

the stove.

Other Firebelly Stove manuals

Firebelly

Firebelly Razen CS1 User manual

Popular Stove manuals by other brands

Arada

Arada Cassette Stove installation guide

Parmco

Parmco FS 600 Installation and operating instructions

MCZ

MCZ SUITE AIR 10 M2 installation guide

HearthStone

HearthStone Stowe DV 8321 Owner's manual & installation guide

Cattara

Cattara FAMILY manual

Stanley

Stanley Argon F500 OVAL Installation and operating instructions

Avalon

Avalon B-VENT instructions

Nordpeis

Nordpeis Vega user manual

Exquisit

Exquisit EKC601-5 Instructions for use and installation

Stanley

Stanley Oisin Oil MK II Installation and operation instruction

Thermocet

Thermocet Brookfield S/CC Operating and installation instructions

HASE

HASE delhi operating instructions

Vermont Castings

Vermont Castings Intrepid 2 User instructions

Italiana Camini

Italiana Camini CLASSICA Installation, use and maintenance

Avalon

Avalon Vashon Avanti DVS FS manual

Spartherm

Spartherm ambiente a1 Installation and operating manual

Dimplex

Dimplex MCFSTV12AU manual

Warmlite

Warmlite WL46040 manual