Fire-Lite H350 User manual

F300-12-00 4 I56-038-00R

Installation and Maintenance Instructions for

Addressable Plug-in Model H350 Thermal Sensor

GENERAL DESCRIPTION

Model H350 is an addressable sensor that uses a state-of-the-art thermistor sensing circuit for fast response. This sensor

is designed to provide open area protection with 50 foot spacing capability, and is intended for use with compatible control

panels only.

Two LEDs on each sensor light to provide a local, visible sensor indication. Remote LED annunciator capability is avail-

able as an optional accessory (Part No. RA400Z).

SPECIFICATIONS

Diameter: 6.1 inches (155 mm) installed in B310LP

Height: 2.0 inches (51 mm)

Weight: 5 ounces (150 gm)

InstallationTemperature: –4°F to 100°F (–20°C to 38°C)

Operating Humidity Range: 10% to 93% Relative Humidity Noncondensing

Mounting: B310LP flanged base

Voltage Range: 15 to 32 Volts DC Peak

Standby Current: 300

A @ 24 VDC (one communication every 5 sec.with LED blink enabled)

LED Current: 6.5 mA @ 24 VDC

Fixed Temperature Setpoint: 135°F (57°C)

WIRING GUIDE

Refer to the installation instructions for the plug-in base being used. Bases are equipped with screw terminals for power, ground,

and remote annunciator connections. See Figure 1.

NOTE: All wiring must conform to applicable local codes, ordinances, and regulations.

NOTE: Verify that all sensor bases are installed and that the wiring polarity is correct at each base.

WARNING: Disconnect the power from the loop before installing sensors.

Before installing sensors, please thoroughly read the system wiring and installation manual, which provides detailed in-

formation on sensor spacing, placement, zoning, and special applications. Copies of these manuals are available from

Fire•Lite. NFPA standard 72 should also be referenced.

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device

may not cause harmful interference, and (2) this device must accept any interference received, including interference that

may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not in-

stalled and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

F300-12-00 1 I56-038-00R

Fire•Lite, One Fire•Lite Place, Northford, CT 06472

Please refer to insert for the Limitations of Fire Alarm Systems

1. Install Sensors:

a. Verify that the sensor type matches the type written on the label in the base.

b. Set the address on the sensor per job drawings.

Note: Some panels support extended addressing. In order to set

the sensor above address 99 on compatible systems, carefully

remove the stop on the upper rotary switch with thumb or finger

as shown in Figure 2.

c. Place the sensor into the sensor base.

d. Turn the sensor clockwise until it drops into place.

e. Continue turning the sensor clockwise to lock it in place.

2. Tamper Resistance

The sensor base includes a tamper proof feature which when activated prevents

removal of the sensor without the use of a tool. See the installation instruction

manual for the sensor base for details in using this feature.

3. After all sensors have been installed, apply power to the control unit.

4. Test the sensor by placing a magnet against the sensor plastic, as shown in Figure 3. The alarm level should be rec-

ognized at the panel and the LED controlled by communication command from the panel.

5. The reset of the sensor LED is controlled by communication command from the panel.

TESTING SENSITIVITY

Sensors must be tested after installation and periodic maintenance. The sensitivity may be tested in the following ways.

A. Test Magnet (p/n M02-04-01 or M02-09-00)

1. Place the optional test magnet against the cover in the magnet test area, as shown in Figure 3, to activate the test

feature.

2. The LEDs should latch on within 10 seconds, indicating alarm and annunciating the panel.

3. Reset the detector at the system control panel.

B. Direct Heat Method (Hair dryer of 1000 – 1500 watts)

1. From the side of the detector, direct the heat toward the sensor. Hold the heat source about 6 inches (15 cm) away

to prevent damage to the cover during testing.

2. The LEDs on the detector should light when the temperature at the detector reaches the alarm setpoint. If the LEDs

fail to light, check the power to the detector and the wiring in the detector base.

3. Reset the detector at the system control panel.

Detectors that fail these tests should be returned for repair.

Figure 3. Views showing position of test magnet.

F300-12-00 2 I56-038-00R F300-12-00 3 I56-038-00R

A78-1478-05

TEST

MAGNET

LED

PAINTED

SURFACE

TEST

MAGNET

PAINTED

SURFACE

MAGNET TEST MARKER

LISTED COMPATIBLE

CONTROL PANEL

Figure 2

45678910

456789

BREAKAWAY STOP

Figure 1

CAUTION: Do not loop wire under terminals 1 or 2.

Break wire run to provide supervision of connections.

Other Fire-Lite Transmitter manuals

Fire-Lite

Fire-Lite H350R User manual

Popular Transmitter manuals by other brands

NIVELCO

NIVELCO EasyTREK SCA-300 Series Programming manual

Honeywell

Honeywell 5816WMBR installation instructions

Kamstrup

Kamstrup READy MTU Installation and operation guide

Omega

Omega ZW Series user guide

ABB

ABB Field 264H Instructions for installation

Alinco

Alinco DJ-V17T Service manual

Dejero

Dejero EnGo 3x manual

Rosemount

Rosemount 4600 Reference manual

Speaka Professional

Speaka Professional 2342740 operating instructions

trubomat

trubomat GAB 1000 instruction manual

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 instructions

Rondish

Rondish UT-11 quick start guide

MG 10JRE instruction manual

Burkert

Burkert 8177 operating instructions

Firetide

Firetide HotPort 3203 Hardware installation guide

Tele Radio

Tele Radio T9-02 User instructions

Rotronic

Rotronic HygroFlex HF3 Series user guide

Jamara

Jamara FCX6 Pro Tel Instruction