Fike VESDA HLI User manual

Product Manual

P/N 06-158, Rev. 5

February 2015

P/N 68-023

HIGH LEVEL INTERFACE (HLI)

VESDAnet Interface

DEVELOPED BY Fike

704 SW 10th Street

P.O. Box 610

Blue Springs, Missouri 64013 U.S.A.

Phone: (888) 628-FIKE (3453)

(816) 229-3405

Fax: (866) 211-9239

Fike copyrights this manual and products it describes. You may not reproduce,

transmit, transcribe, or any part of this manual without express, written

permission from Fike.

This manual contains proprietary information intended for distribution to

authorized persons or companies for the sole purpose of conducting business

with Fike. If you distribute any information contained in this manual to

unauthorized persons, you have violated all distributor agreements and we may

take legal action.

TRADEMARKS Fike©is a registered trademark of Fike.

QUALITY Fike has maintained ISO 9001 certification since 1996. Prior to shipment, we

thoroughly test our products and review our documentation to assure the highest

quality in all respects.

WARRANTY Fike provides a one-year limited manufacturer’s warranty on this product. All

warranty returns must be returned from an authorized Fike Distributor. Contact

Fike’s Marketing department for further warranty information.

Fike maintains a repair department that is available to repair and return existing

electronic components or exchange/purchase previously repaired inventory

component (advance replacement). All returns must be approved prior to return.

A Material Return Authorization (MRA) number must be indicated on the box of

the item being returned. Contact the appropriate Regional Sales Manager for

further information regarding product return procedures.

LIMITATIONS OF LIABILITY Installation in accordance with this manual, applicable codes, and the

instructions of the Authority Having Jurisdiction is mandatory. Fike can not be

held liable for any incidental or consequential damages arising from the loss of

property or other damages or losses resulting from the use or misuse of Fike

products beyond the cost of repair or replacement of any defective components.

Fike reserves the right to make product improvements and change product

specifications at any time.

While every precaution has been taken during the preparation of this manual to

ensure the accuracy of its content, Fike assumes no responsibility for errors or

omissions.

HIGH LEVEL INTERFACE

UL S3217 P/N 06-158 1

FM 3020297 Rev 5, 02/2015

TABLE OF CONTENTS

Section Page

1.0 About This Manual.....................................................................................................................................3

1.1 Document History ................................................................................................................................3

1.2 Product Support...................................................................................................................................3

1.3 Related Documentation .......................................................................................................................4

1.4 Terms Used in this Manual..................................................................................................................5

1.5 Symbols Used in this Manual ..............................................................................................................6

1.6 Safety Notices......................................................................................................................................6

2.0 Product Overview ......................................................................................................................................7

2.1 Ordering Information............................................................................................................................7

2.2 Physical Specifications ........................................................................................................................7

2.3 Electrical Specifications .......................................................................................................................8

3.0 Installation..................................................................................................................................................9

3.1 Mounting Location ...............................................................................................................................9

3.2 Enclosure Installation...........................................................................................................................9

3.3 HLI Wiring ..........................................................................................................................................10

3.4 VESDAnet Wirng ...............................................................................................................................13

4.0 Configuration...........................................................................................................................................14

4.1 Cheetah Configuration of VESDA Units .......................................................................................14

4.2 CyberCat/Cheetah Xi Configuration of VESDA Units ..................................................................16

5.0 Operation .................................................................................................................................................19

5.1 Silence and Acknowledge Switches.............................................................................................19

5.2 Reset Switch.................................................................................................................................19

5.3 Trouble Interactions......................................................................................................................20

5.4 Graphic Annunciator.....................................................................................................................20

5.5 Operation - Cheetah .....................................................................................................................20

5.6 Operation - CyberCat / Cheetah Xi ..............................................................................................22

5.7 Cheetah / VESDA Alarm Levels...................................................................................................24

5.8 CyberCat / Cheetah Xi / VESDA Alarm Levels ...........................................................................26

6.0 Trouble Reporting / Diagnostics ...........................................................................................................31

6.1 Cheetah / VESDA Link .................................................................................................................31

6.2 CyberCat / Cheetah Xi / VESDA Link...........................................................................................32

7.0 Service......................................................................................................................................................34

7.1 Cheetah .......................................................................................................................................34

7.2 CyberCat / Cheetah Xi..................................................................................................................36

Appendix 1 Cheetah Event Messages .........................................................................................................38

Appendix 2 CyberCat / Cheetah Xi Event Messages..................................................................................41

HIGH LEVEL INTERFACE

2 P/N 06-158 UL S3217

Rev 5, 02/2015 FM 3020297

LIST OF EXHIBITS

Exhibit Page

1 Circuit Board Assembly .......................................................................................................................... 7

2 Ordering Information............................................................................................................................... 7

3 Circuit Board Wiring Connections .......................................................................................................... 8

4 Terminal Block Specifications ................................................................................................................ 8

5 Enclosure Installation ............................................................................................................................. 9

6 Cheetah HLI Wiring Diagram ............................................................................................................... 10

7 Cheetah Xi and CyberCat HLI Wiring Diagram.................................................................................... 11

8 Cheetah Xi 50 and CyberCat 50 HLI Wiring Diagram.......................................................................... 12

9 VESDAnet Interface Example .............................................................................................................. 13

10 VESDA Laser Plus Configuration......................................................................................................... 14

11 Laser Scanner Configuration................................................................................................................ 15

12 Laser Compact Configuration............................................................................................................... 15

13 Configuration Menu 4 ........................................................................................................................... 16

14 VESDA Configuration Menu................................................................................................................. 16

15 VESDA Alarm Menu ............................................................................................................................. 16

16 VESDA Sector Zone Menu................................................................................................................... 17

17 VESDA Loop/Addr Menu...................................................................................................................... 17

18 VESDA Release Menu ......................................................................................................................... 18

19 Cheetah – Alert Level ........................................................................................................................... 24

20 Cheetah – Alert Restored..................................................................................................................... 24

21 Cheetah – Action Level ........................................................................................................................ 25

22 Cheetah – Action Restored .................................................................................................................. 25

23 Cheetah – Fire 1 Level ......................................................................................................................... 25

24 Cheetah – Fire 2 Level ......................................................................................................................... 26

25 CyberCat/Cheetah Xi – Alert Level ...................................................................................................... 26

26 CyberCat/Cheetah Xi – Alert Level Details .......................................................................................... 27

27 CyberCat/Cheetah Xi – Alert Clear ...................................................................................................... 27

28 CyberCat/Cheetah Xi – Action Level.................................................................................................... 28

29 CyberCat/Cheetah Xi – Action Level Details........................................................................................ 28

30 CyberCat/Cheetah Xi – Action Clear.................................................................................................... 28

31 CyberCat/Cheetah Xi – Fire 1 Level..................................................................................................... 29

32 CyberCat/Cheetah Xi – Fire 1 Level Details......................................................................................... 29

33 CyberCat/Cheetah Xi – Fire 2 Level..................................................................................................... 29

34 CyberCat/Cheetah Xi – Fire 2 Level Details......................................................................................... 30

35 Cheetah – Event Trouble...................................................................................................................... 31

36 Cheetah – Event Restored ................................................................................................................... 31

37 Cheetah – Event Trouble...................................................................................................................... 32

38 Cheetah – Event Restored ................................................................................................................... 32

39 CyberCat/Cheetah Xi – Event Trouble ................................................................................................. 32

40 CyberCat/Cheetah Xi – Trouble Restore.............................................................................................. 33

41 CyberCat/Cheetah Xi – Trouble Restore.............................................................................................. 33

42 CyberCat/Cheetah Xi – Trouble Restore.............................................................................................. 33

43 Cheetah – VESDA Levels .................................................................................................................... 34

44 Cheetah – Alarm Threshold ................................................................................................................. 35

45 Cheetah – Isolate Function................................................................................................................... 35

46 Diagnostic Menu 2................................................................................................................................ 36

47 VESDA Diagnostic Menu...................................................................................................................... 36

48 VESDA Diagnostic Menu...................................................................................................................... 36

49 CyberCat/Cheetah Xi – VESDA Isolated.............................................................................................. 37

50 CyberCat/Cheetah Xi – Isolate Clear ................................................................................................... 37

HIGH LEVEL INTERFACE

UL S3217 P/N 06-158 3

FM 3020297 Rev 5, 02/2015

1.0 ABOUT THIS MANUAL

This manual is intended to be a reference for the installation and operation of the VESDA High Level Interface

(HLI) Module. The information contained in this manual must be utilized by the factory trained Fike distributor

in order to properly install and test the device to ensure proper operation. This manual is not designed to be

a full Operations Manual for the end user.

Before you refer to any section in this manual, and before you attempt to install or use, be sure to read the

important safety notices in Section 1.6.

This manual is divided into sections for easy reference. The first-time installer and/or user should thoroughly

read and understand the instructions contained within this manual before using this device. These

instructions must be followed to avoid possible damage or adverse operating conditions caused by improper

installation, wiring and/or programming.

1.1 DOCUMENT HISTORY

Document Title: VESDA Network Interface – Product Manual

Document Reorder Number: 06-158

Revision Section Date Reason for Change

0 All Sections 10/2003 Initial Release

1 All Sections 09/2004 Updates to Firmware & Manual Format Corrections

2 All Sections 03/2007 Include Operation with CyberCat and Cheetah Xi

3 All Sections 10/2008

Changed the number of VESDA units that can be

connected to HLI if used for primary detection to 10

maximum

4 All Sections 04/2010

Changed the number of VESDA units that can be

connected to HLI if used for primary detection to 40

maximum

5 Section 2.3 02/2015 Updated HLI current draw.

1.2 PRODUCT SUPPORT

If you have a question or encounter a problem not covered in this manual, you should first try to contact the

distributor that installed the protection system. Fike has a worldwide distribution network. Each distributor

sells, installs, and services Fike equipment. Look on the inside of the door, left side, there should be a sticker

with an indication of the distributor who sold the system. If you can not locate the distributor, please call Fike

Customer Service for locating your nearest distributor, or go to our web-site at www.fike.com. If you are

unable to contact your installing distributor or you simply do not know who installed the system you can

contact Fike Product Support at (800) 979-FIKE (3453), Option 21 Monday through Friday,

8:00 a.m. to 4:30 p.m. CST.

HIGH LEVEL INTERFACE

4 P/N 06-158 UL S3217

Rev 5, 02/2015 FM 3020297

1.3 RELATED DOCUMENTATION

To obtain a complete understanding of the specific features of the VESDA HLI or to become familiar with

related functions and networking to Fike panels, refer to the documentation listed below. Please reference

the most current version or the version noted on the label located on the product.

Document Title Part Number

Cheetah Installation, Operation and Maintenance Manual 06-148

CyberCat (254/1016) Addressable Fire Alarm Product Manual 06-326

Cheetah Xi Addressable Fire Suppression Product Manual 06-356

CyberCat 50 Addressable Fire Alarm Product Manual 06-368

Cheetah Xi 50 Addressable Fire Suppression Product Manual 06-369

VESDA LaserCOMPACT Product Guide - Xtralis Part No. 18938

VESDA LaserPLUS Product Guide – Xtralis Part No. 19145

VESDA LaserSCANNER Product Guide – Xtralis Part No. 19147

VESDA LaserFocus Product Guide (VLF250) – Xtralis Part No. 20295

VESDA LaserFocus Product Guide (VLF 500) – Xtralis Part No. 20297

HIGH LEVEL INTERFACE

UL S3217 P/N 06-158 5

FM 3020297 Rev 5, 02/2015

1.4 TERMS USED IN THIS MANUAL

The following are various terms used in this manual with a brief description of each:

Ω- Symbol for “ohm”. Unit of resistance.

AC Normal State

(“AC Normal” Green LED ON) The system is in the AC Normal state when appropriate AC power is being applied to

the system.

Alarm State

(“Alarm” Red LED ON, Piezo pulsing) The alarm occurs when an input circuit configured for alarm operation has

been activated. Activation typically initiated by a detector or contact device. The system leaves the alarm state

upon entry into the pre-discharge or release state.

Class A wiring

Input circuits capable of transmitting an alarm signal during a single open or a non-simultaneous single ground fault

on a circuit conductor shall be designated as Style D or Class A. Similarly, output circuits capable of activating

during a single open or a non-simultaneous ground fault on a circuit conductor shall be designated as Style Z or

Class A. Commonly referred to as redundant or 4-wire connection; this manual refers to 4-wire connections as

Class A wiring.

Class B wiring

Input circuits incapable of transmitting and alarm signal beyond the location of the fault condition (listed for Class A

wiring above) shall be designated as Style B or Class B. Similarly, output circuits incapable of operating beyond the

location of the fault condition shall be designated as Style Y or Class B. This manual refers to 2-wire connections

as Class B wiring.

Initiating Device

A system component that originates transmission of a change-of-state condition, such as a smoke detector, manual

fire alarm box, or supervisory switch. This manual interchanges the terms initiating device and input device.

Initiating Device Circuit

A circuit to which automatic or manual initiating devices are connected where the signal received does not identify

the individual device operated. This manual interchanges the terms initiating device circuit and input circuit.

Normal State

(“Trouble” Yellow LED OFF) The system is in the normal state when the power supply and all circuits are configured

properly, connected, and responding properly. The system remains in normal state until a trouble condition occurs.

Non Power-Limited

A circuit designation given for wiring purposes. The amount of current flowing through the circuit is unlimited vs.

being limited, or power-limited. AC power and Battery wiring is Non Power-limited.

Power-Limited

A circuit designation given for wiring purposes. The amount of current flowing through the circuit is limited (typically

by fuse) vs. being unlimited, or non-power-limited. The SHP Pro input and output circuits are power-limited. The

circuit has a maximum power that flows through it or it current limits and opens the circuit.

Pre-discharge State

(“Alarm” Red LED ON, Piezo chirping) The pre-discharge state occurs when the zone’s detection type input

conditions are satisfied (Cross Zone Detection, Sequential Alarm Detection, or Single Detector Release). Upon

time delay countdown completion (unless delayed by a pertinent activated abort input), the system leaves the pre-

discharge state and enters the release state.

Release State

(“Alarm” Red LED ON, Piezo chirping) The release state occurs upon completion of the pre-discharge state or upon

activation of a manual release input. At the start of the release state, output circuits configured for releasing shall

operate. (Does not apply to CyberCat)

HIGH LEVEL INTERFACE

6 P/N 06-158 UL S3217

Rev 5, 02/2015 FM 3020297

1.5 SYMBOLS USED IN THIS MANUAL

The following cautions and warnings appear in this manual. Be certain to read all of the following warning

and cautions before attempting to install or use this device. Personal injury or accidental release of the

suppression system may result if these warnings and cautions are not followed.

aWARNING

This symbol is used in this manual to warn of possible injury or

death from improper use or application of the product under noted

conditions.

ICaution

Cautions are used to indicate the presence of a hazard which will

or may cause damage to the equipment if safety instructions are

not followed or if the hazard is not avoided.

LNote: Provides information on installation, operation,

maintenance, performance or general tips that are important but

not hazardous to anything or anyone.

1.6 SAFETY NOTICES

Be certain to read all the following warnings and cautions before installing or using this device.

Accidental damage to the device could result if these warnings and cautions are not heeded!

aWARNING

Failure to disconnect power to the releasing circuit(s) and

completely disarm the solenoid(s) or any other "critical

operation" contacts prior to system testing may cause accidental

activation of the system.

ICaution

To ensure proper system operation after installation of the

VESDA HLI, this device must be tested in accordance with

NFPA 72. Re-acceptance testing is required after any change,

addition or deletion of system components, or after any

modification, repair or adjustment to system hardware or wiring.

ICaution

The VESDA HLI Interface contains static sensitive components.

Handle the electronics by the edges only and avoid touching the

integrated components. Keep the electronics in the protective

static bags it was shipped in until time for installation. Always

ground yourself with a proper wrist strap before handling the

module(s). If the installer is properly grounded at all times,

damage due to static discharge will not occur. If the module

requires repair or return to Fike, it must be shipped in an anti-

static bag.

HIGH LEVEL INTERFACE

UL S3217 P/N 06-158 7

FM 3020297 Rev 5, 02/2015

2.0 PRODUCT OVERVIEW

The VESDA Open Protocol High Level Interface (HLI) is used to

link VESDA detectors, displays and programmers connected to

the “VESDAnet” with compatible Fike control panels (i.e.,

Cheetah, Cheetah Xi and CyberCat). The host control panel will

poll the HLI which will then transmit all VESDAnet detector

information intelligently into the control panel. Refer to the

VESDA System Design Manual for a detailed description of

connecting to a VESDAnet system.

The HLI (P/N 68-023) is sold as an assembly that consists of the

following components:

•16 gauge, painted steel enclosure with cover, painted gray

•Printed circuit board with HLI attached

•Communication cable, HLI to host panel

The number of VESDA detectors that can be connected to a single HLI varies depending upon the firmware

version of both the HLI and host control panel. If using an HLI with firmware V3.08.0.0 or higher in

conjunction with a host control panel with firmware V4.20 or higher; up to 40 VESDA detectors can be

connected to the HLI. If using a VESDA HLI with firmware older than V3.08.0.0 or a host control panel with

firmware older than V4.20; up to 10 VESDA detectors can be connected to the HLI. These limitations must

be adhered to in order to allow the VESDAnet detectors to meet the device response time requirements set

forth by UL standard 864 (ninth edition) and NFPA 72.

2.1 ORDERING INFORMATION

Part Number Description

68-023 High Level Interface (HLI) Assembly

10-2277 HLI Printed Circuit Board Assembly (included in 68-023)

68-037 Open Protocol HLI (included in 10-2277)

02-4551 HLI Enclosure, Gray (included in 68-023)

02-3053 RS232 Serial Cable (included in 68-023), 4 conductor, 14 ft. (4.26 m)

Exhibit 2: Ordering Information

2.2 PHYSICAL SPECIFICATIONS

Environmental: All electronics are rated 32°- 120°F (0°- 49°C)

93% relative humidity

Enclosure Dims (HxWxD): Backbox - 6" (15.24 cm) x 12" (30.5 cm) x 4" (10 cm)

Cover - 7" (17.8 cm) x 13" (33 cm) x 1/8" (.32 cm)

Enclosure Mounting: Surface mount only using four holes provided in enclosure back box

10 inch (25.4 cm) horizontal centers, 4 inch (10 cm) vertical centers

Exhibit 1: Circuit Board Assembly

HIGH LEVEL INTERFACE

8 P/N 06-158 UL S3217

Rev 5, 02/2015 FM 3020297

2.3 ELECTRICAL SPECIFICATIONS

The HLI provides two terminal blocks which allow connection of the 24VDC power input and VESDAnet

wiring. A RJ11 jack is provided to allow connection of the interconnection cable between the HLI and the

host control panel (See Exhibit 3).

Exhibit 4: Terminal Block Specifications

TERMINAL DESCRIPTION NOMINAL RANGE SPECIFICATION DETAILS

P10

Term: 24 VDC

0 VDC

24 VDC

0 VDC

24VDC Power input

Incoming

Outgoing

Power-limited

Supervised

245 mA @ 24VDC (standby and alarm)

Power for VESDA High Level Interface must

come from Power Supply on Fike Control Panel

or Ground fault could result.

Wiring 16AWG minimum, THHN

Terminal block accepts 12 AWG–16 AWG

A+

A-

Shield

B+

B-

Shield

VESDAnet

Incoming

Outgoing

RS485

Non-power-limited

Supervised

120Ωimpedance shielded twisted pair cable

(Belden 9841 wiring or equivalent)

4265 ft. (1300 m) maximum between two

VESDAnet devices

Maximum 40 VESDA detectors connected to

HLI if used for primary detection

Panel RS232 data

RS232

Supervised

Non-power limited

Serial communication cable

20 ft. (6.1 m) maximum cable length in conduit

to Fike Control Panel located in same room

Cable shipped with assembly is 14 ft. (4.26 m)

in length

24VDC FROM PANEL

24VDC OUT TO NEXT DEVICE

SHIELD

WIRE

+24V

VESDA PC Link HLI

P10

+24V

V'net A+

V'netA-

SHLD

V'net B+

V'netB-

SHLD

SHIELD

WIRE

VESDAnetIN

VESDAnet OUT

RS232 CABLE TO

CONTROL PANEL

Exhibit 3: Circuit Board Wiring Connections

This manual suits for next models

Table of contents

Other Fike Recording Equipment manuals

Fike

Fike 70-290 User manual

Popular Recording Equipment manuals by other brands

KV2 Audio

KV2 Audio 500 Series user guide

Robotics Technologies

Robotics Technologies microBus-Cam II installation manual

Seca

Seca 460 quick start guide

Cognex

Cognex MVS-8000 Series Hardware manual

Mect

Mect MPNC006 Series user manual

Bad Caf

Bad Caf THE LEASH operating manual

Strymon

Strymon NIGHTSKY user manual

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U user manual

Tews Technologies

Tews Technologies TPMC465 user manual

Honeywell

Honeywell Excel 50 user guide

SeaLevel

SeaLevel COMM+8.LPCI user manual

Arturia

Arturia AUDIOFUSE STUDIO user manual

Rukra

Rukra RK-1240 quick start guide

Samson

Samson SCOM owner's manual

Dynacord

Dynacord DPS260 owner's manual

Nice

Nice Core user manual

Pyle Pro

Pyle Pro PSS8 manual

RF-System

RF-System TinyGate Assembly and user's manual