FIBARO FGWDSEU-221-8 User manual
FIBARO WALLI DOUBLE SWITCH
FGWDSEU-221
OPERATING
MANUAL EN
v1.0
3
Table of contents
1: Important safety information 4
2: Description and features 5
2.1: Description 5
2.2: Main features 5
3: Specications 6
4: Installation 7
4.1: Before installation 7
4.2: Preparing for installation 8
4.3: Electrical connection 8
4.4: Assembling the device 9
4.5: Activating the device 10
5: Adding to Z-Wave network 11
5.1: Adding manually 11
5.2: Adding using SmartStart 12
6: Removing from Z-Wave network 13
7: Operating the device 14
7.1: Controls 14
7.2: Single/Double Switch operating mode 14
7.3: Button control 15
7.4: Visual indications 15
7.5: Menu 16
7.6: Resetting to factory defaults 16
8: Power and energy metering 17
9: Conguration 18
9.1: Associations 18
9.2: Advanced parameters 21
10: Z-Wave specication 36
11: Parts compatibility 39
12: Regulations 40
4
Important safety InformatIon
1: Important safety information
Read this manual before attempting to install the device!
!Failure to observe recommendations included in this manual
may be dangerous or cause a violation of the law. The manu-
facturer, Fibar Group S.A. will not be held responsible for any loss or
damage resulting from not following the instructions of operating
manual.
DANGER OF ELECTROCUTION!
The device is designed to operate in electrical home installa-
tion. Faulty connection or use may result in re or electric
shock.
All works on the device may be performed only by a qualied
and licensed electrician. Observe national regulations.
Even when the device is turned o, voltage may be present at
its terminals. Any maintenance introducing changes into the
conguration of connections or the load must be always performed
with disabled fuse.
To avoid risk of electrical shock, do not operate the device with
wet or moist hands.
Do not modify!
!Do not modify this device in any way not included in this
manual.
Other devices
!The manufacturer, Fibar Group S.A. will not be held responsi-
ble for any damage or loss of warranty privileges for other con-
nected devices if the connection is not compliant with their
manuals.
This product is intended for indoor use only in dry locations.
!Do not use in damp or wet locations, near a bathtub, sink,
shower, swimming pool, or anywhere else where water or
moisture are present.
Not a toy!
!This product is not a toy. Keep away from children and
animals!
5
DescrIptIon anD features
2: Description and features
2.1: Description
FIBARO Walli Double Switch is a smart wall switch designed to con-
trol one or two light sources via Z-Wave network.
It measures active power and energy consumed by the controlled
load.
You can install it with provided cover plate and switch button or oth-
er compatible.
2.2: Main features
• Can be used with:
»conventional incandescent and halogen light sources,
»LED lamps,
»uorescent lamps,
»electronic transformers (for ELV halogen lamps and LED bulbs),
»ferromagnetic transformers (for MLV halogen lamps).
• Can be used with FIBARO Walli covers or other compatible (see
“Parts compatibility” on page 39):
»GIRA – System 55 (Standard 55, E2, Event, Event Clear),
»Legrand – Céliane,
»Schneider – Odace.
• Active power and energy consumption metering.
• Supports Z-Wave network Security Modes: S0 with AES-128 en-
cryption and S2 Authenticated with PRNG-based encryption.
• Works as a Z-Wave signal repeater (all non-battery operated de-
vices within the network will act as repeaters to increase reliabili-
ty of the network).
• May be used with all devices certied with the Z-Wave Plus cer-
ticate and should be compatible with such devices produced by
other manufacturers.
i
The device is a Security Enabled Z-Wave Plus product
and a Security Enabled Z-Wave Controller must be
used in order to fully utilize the product.
6
specIfIcatIons
3: Specications
Power supply 110-230V~ 50/60 Hz
Rated load current 13A per one channel
16A total
Compatible load types incandescent bulbs
uorescent lamps
electronic transformers
ferromagnetic transformers
LED
Active element micro-gap relay μ
Recommended external
overcurrent protection
10A type B circuit breaker (EU)
13A type B circuit breaker (Sweden)
For installation in boxes Ø = 60mm, depth ≥ 40mm
Recommended wires cross-section area between 1.5-4.0mm2,
stripped 11.5-13mm of insulation
Operating temperature 0–35°C
Ambient humidity 10–95% RH without condensation
Radio protocol Z-Wave (500 series chip)
Radio frequency band 868.0–868.6MHz; 869.7–870.0MHz
Max. transmitting power +6dBm
Range up to 50m outdoors
up to 40m indoors
(depending on terrain and building
structure)
Dimensions
(Height x Width x Depth)
86 x 86 x 51 mm
Compliance with EU
directives
RoHS 2011/65/EU
RED 2014/53/EU
i
Radio frequency of individual device must be same as
your Z-Wave controller. Check information on the box
or consult your dealer if you are not sure.
7
InstallatIon
4: Installation
4.1: Before installation
!Connecting the device in a manner inconsistent with this
manual may cause risk to health, life or material damage.
• Do not power the device before fully assembling it in the mount-
ing box,
• Connect only in accordance with one of the diagrams,
• Install only in ush mounting boxes compliant with a relevant na-
tional safety standards and with depth no less than 40mm,
• Do not connect devices which are not compliant with the speci-
cation or relevant safety standards,
• Do not connect heating devices,
• Do not connect SELV or PELV circuits.
• Make sure you have all required parts when installing with covers
other than FIBARO (see “Parts compatibility” on page 39).
Device parts:
1
2
3
4
1 – switch button, 2 – cover plate, 3 – unit (device), 4 – mounting
frame
Notes for diagrams:
N – terminal for neutral wire
Q1 – output terminal of the 1st channel
Q2 – output terminal of the 2nd channel
L – terminal for live wire
G – groove used to measure wire length
8
InstallatIon
4.2: Preparing for installation
Prepare wires by removing 11.5-13mm of insulation from their ends.
You can use groove on the side of the unit to measure the length.
When installing with FIBARO or GIRA cover plates:
1. Pull out the switch button.
2. Take o the cover plate.
When installing with Legrand or Schneider cover plates:
1. Pull out the original switch button.
2. Take o the original cover plate.
3. Dismount the original mounting frame.
4. Snap the new mounting frame*.
* Additional mounting frames are sold separately.
4.3: Electrical connection
1. Switch o the mains voltage (disable the fuse).
2. Connect with one of the diagrams below:
N
L
Diagram 1: Example con-
nection for double switch
conguration
N
L
Diagram 2: Example con-
nection for single switch
conguration
3. Verify correctness of connection.
4. Tighten the terminal screws using PH1 screwdriver.
9
InstallatIon
4.4: Assembling the device
i
When installing the device in the mounting box orient
the device with terminal screws going up or to the left
(for horizontal button position) to ensure button order.
i
The light eect might look dierent for covers other
than Walli. You can adjust colour and/or intensity of
the LEDs to suit the particular cover (using parameters 11,
12, and 13) or disable it by changing parameter 13 to 0.
When installing with FIBARO cover plates:
1. Insert the device with mounting frame into the mounting box and
secure with mounting claws and screws.
2. Snap the cover plate to the device.
3. Snap the switch button to the device.
When installing with GIRA cover plates:
1. Insert the device with mounting frame into the mounting box and
secure with mounting claws and screws.
2. Snap the new cover plate to the device.
3. Snap the switch button adapter* to the device.
4. Snap the new switch button to the device.
10
InstallatIon
When installing with Legrand cover plates:
1. Insert the device with mounting frame* into the mounting box
and secure with mounting claws and screws.
2. Snap the switch button adapter* to the device.
3. Snap the new inner cover plate to the device.
4. Snap the new outer cover plate to the device.
5. Snap the new switch button to the device.
When installing with Schneider cover plates:
1. Insert the device with mounting frame* into the mounting box
and secure with mounting claws and screws.
2. Snap the new cover plate to the device.
3. Snap the new switch button to the device.
* Switch button adapter and additional mounting frames
are sold separately.
4.5: Activating the device
1. If the device fully assembled, switch on the mains voltage.
2. LED ring light means the device is powered and can be added to
the Z-Wave network.
This manual suits for next models
2
Table of contents
Other FIBARO Switch manuals
FIBARO
FIBARO FGS-221-EN-A-v1.00 User manual
FIBARO
FIBARO FGS-213 User manual
FIBARO
FIBARO Wall Plug User manual
FIBARO
FIBARO FGS-2x3 User manual
FIBARO
FIBARO FGS-213 User manual
FIBARO
FIBARO FGS-212-EN-A-v1.01 User manual
FIBARO
FIBARO Smart Module User manual
FIBARO
FIBARO FGBHS-213 User manual
FIBARO
FIBARO WALLI FGWDSEU-221 User manual
FIBARO
FIBARO FGWPG-121 User manual
