Festool ROTEX RO 150 User manual
1/4
Description
Whether it is coarse sanding or fine sanding, overhead work or work in
upright areas, the ROTEX can be used everywhere - even in places that
are difficult to access.
The tool is also used for polishing in body workshops and by carpenters.
Areas of application RO 125 RO 150
Removal capacity + ++
Ergonomics ++ ++
Surface quality ++ ++
Processing large areas + ++
Upright work and overhead work ++ +
A
601/01
No. 601
Operation and function of
the ROTEX
601/02
601/03
601/04
2/4
B
Tools/Accessories
The following tools and accessories are used in this application example:
601/06
Designation Order No.
Geared eccentric sander ROTEX, RO 125 FEQ Plus 571533
Geared eccentric sander ROTEX, RO 150 FEQ Plus 571570
601/05
3/4
C
601/08
Preparation/Set-up
The economical 3-in-1 principle: one machine - three applications
Coarse sanding (also called rotary sanding)•
With this motion the pad is driven using a gear - forced rotation.
With the combination of eccentric and rotary motions the ROTEX
achieves up to three times higher material removal capacity than
other eccentric sanders.
Fine sanding (also called eccentric sanding)•
In this motion the pad rotates itself. You obtain a first-class, extra-fine
sanding pattern with this classic eccentric motion. If the machine
is pressed to hard on the workpiece, the pad sticks - this should be
avoided!. (This will have a negative impact on the sanding result).
Polishing (with the ROTEX rotary motion)•
For this application a rotation is needed so the gear is switched on.
The overlapping rotary and eccentric motions of the ROTEX ensure
optimal results also for polishing.
601/07
601/09
Procedure
To switch the machine from coarse sanding to fine sanding or vice-versa the
motor must be switched off.
The switching is effected via the slide switch located in the centre of the cap.•
If the switch is moved to the right (rough tab), the machine is in coarse•
sanding/rotary mode.
If the switch is moved to the left (fine tab), the machine is in fine sanding/•
eccentric sanding mode.
E
601/10
4/4
Our example for use is a recommendation tried and tested in practice. However the
actual conditions pertaining in each situation are completely outside of our control.
We therefore do not provide any form of guarantee. Any legal claims arising out of
this are not to be made against Festool. Please observe without fail the safety and
operating instructions included with the product.
www.festool.com
Pad change for the RO 125 FEQ
Disconnect the tool from the power supply.•
Remove the protector if this is mounted.•
Set the switch on the cap to coarse sanding (rotary mode).•
Press the lock button, which is located at the rear of the machine•
(this must be pulled out slightly for pressing).
Remove the sanding pad (anti-clockwise).•
Now put the other sanding pad in its retainer and secure it firmly•
into place (in clockwise direction).
601/1!
601/12
601/13
Positioning the protector
The protector prevents the sanding pad coming into contact with its•
other side (e.g. when sanding along a wall) and thus a kick-back of the
machine.
For assembly place the edge protection on the machine until you hear•
it lock in to place.
For removal pull out or press the protector on one end and then push•
it out from the guide.
Pad change for the RO 150 FEQ
Proceed as for RO 125.•
The lock button is located at the front of the machine at the side on the•
RO 150.
Also here the button must be pulled up slightly so that it can be pressed.•
Remove extraction channel (RO 150 FEQ)
As dust extraction is not required for polishing the extraction channel if
connected is removed as it may be an obstruction.
To do so the green button in the handle area must be pressed in the•
direction of the extractor connector. At the same time pull the extraction
channel to the back.
601/14
This manual suits for next models
1
Table of contents
Other Festool Sander manuals
Festool
Festool LEX 2 150/3 User manual
Festool
Festool RS 200 EQ User manual
Festool
Festool ETS EC 150/3 A EQ User manual
Festool
Festool ETSC 125 Li User manual
Festool
Festool RS 200 EQ Installation instructions
Festool
Festool WTS 150/7 E Installation instructions
Festool
Festool ETS EC 125/3 EQ User manual
Festool
Festool ETS 150/3 EQ User manual
Festool
Festool LRS 93 M Installation instructions
Festool
Festool ETS 150/3 EQ User manual
Festool
Festool ETS 125 REQ User manual
Festool
Festool LRS 93 M Installation instructions
Festool
Festool ETS EC 150/3 EQ User manual
Festool
Festool ETS 150/3 EQ User manual
Festool
Festool RTS 400 REQ Installation instructions
Festool
Festool ETS EC 125/3 EQ Installation instructions
Festool
Festool RS 2 User manual
Festool
Festool RS 100 CQ Installation instructions
Festool
Festool Sanders User manual
Festool
Festool PSB 300 Q Installation instructions
