Festool VS-600 Manual

Page 1 of 5 www.festool-usa.com

VS600 Jointing System — Procedure for Half Blind Dovetails

A Step by Step Procedure for these templates: SZ14 and SZ20

Template SZ14 - Half Blind Dovetail

for wood thickness .63 - .79" (26-20mm)*

Cutters: 490 991 (HSS); 490 990 (carbide)

Template SZ20 - Half Blind Dovetail

for wood thickness .63 - .79" (26-20mm)*

Cutters: 490 991 (HSS); 490 990 (carbide)

* wood thickness measurements refer to front/back

piece only - sides can be thinner.

Install the copying ring. The ring should be the

one that came with the SZ14 or SZ20

template or one that fits in the template

grooves exactly.

Install the appropriate bit in the router.

Cutters: 490 991 (HSS)

490 990 (carbide)

Page 2 of 5 www.festool-usa.com

Install SZ14 Template. Before tightening

locking knobs, be sure the alignment shoulders

on underside are touching the base.

Rotate end stops so that SZ14 is pointing to

wood edge.

I lower the template and adjust the two black

positioners so they are in the "D" window.

I move the black positioner left and right until

the arrows are touching the flat side of the "D"

and lock it in that place.

Page 3 of 5 www.festool-usa.com

This is the drawing from the Manual. You

should mark the pieces of your box

accordingly.

I have laid out the test drawer and have

numbered everything the exact same way.

Position the front/back piece in the horizontal

clamp with insides facing up. The "A"

corners will be on the left; the "B" on the right.

Position the sidepiece with the inside edge

facing front and touching the underside of the

template.

Make sure the front/back piece is touching the

backside of the sidepiece end.

Page 4 of 5 www.festool-usa.com

Zero router by placing it on the template and

plunge the bit until it "kisses" the top of the

wood. Lock the plunge.

Move the plunge rod to the 12mm position.

This is the recommended start depth for use

with this template.

I move the router over where it is still on the

template but no wood is beneath. I plunge to

the preset point and lock the plunge setting.

I also adjust the dust hood so that it allows

free movement of the router on the template

— including room to cut the tails.

Page 5 of 5 www.festool-usa.com

It doesn't take long to run the router for both

the "A" and "B" joints. I have made a very

light pass from right to left (climb cut) — this

will reduce tear out. Then, guide the router

into each of the fingers.

Test fit the pieces. They are exact. I did spray

paint the "A" front side for a contrast —

otherwise, these photos are unretouched.

This template can do great drawers. At the

right, the front joint is with 3/4" front and 3/4"

sides. Since many cabinets have drawers with

1/2" sides and 3/4" fronts, the upper example

is just that and did not require any change to

the set-up.

It can even do 1/2-blind dovetails with a

rabbet front.

Other manuals for VS-600

Table of contents

Other Festool Power Tools manuals

Festool

Festool OF 1010 EQ User manual

Festool

Festool BG-RG 150 Installation instructions

Festool

Festool RW 1000 EQ User manual

Festool

Festool Carvex PSC 400 EB User manual

Festool

Festool CONTURO User manual

Festool

Festool PSC 420 EB User manual

Festool

Festool KA 65 User manual

Festool

Festool Trion PS 300 EQ User manual

Festool

Festool Domino XL DF 700 Owner's manual

Festool

Festool OF 1010 Q Installation instructions

Festool

Festool VECTURO OS 400 EQ User manual

Festool

Festool OF 1400 EB Installation instructions

Festool

Festool Domino DF 500 Owner's manual

Festool

Festool VS-600 User manual

Festool

Festool Trion PS 300 EQ User manual

Festool

Festool HKC 55 EB User manual

Festool

Festool MFK 700 EQ User manual

Festool

Festool Carvex PS 420 EBQ User manual

Festool

Festool OF 2200 EB Installation instructions

Festool

Festool Domino Machine User manual

Festool

Festool OF 2200 EB User manual

Festool

Festool MFK 700 EQ User manual

Festool

Festool PSB 400 EBQ User manual

Festool

Festool OF 2000 E User manual

Popular Power Tools manuals by other brands

AEG

AEG OMNI-JS Original instructions

SIP

SIP 01533 manual

Ribimex

Ribimex PRS499 quick start guide

3M Fiber Optic Connector Crimp Tool instructions

Ryobi

Ryobi P524 Operator's manual

ROJEK

ROJEK FSN 300A manual

Kemper

Kemper 1740PRO manual

WABCO

WABCO OptiTire installation manual

EINHELL

EINHELL TE-MS 18/210 Li Original operating instructions

Orgapack

Orgapack OR-T 85 Operating and safety instructions

TOUGHCUT

TOUGHCUT Diamond 400 instruction manual

Yaros

Yaros PB-3603 user manual

Fein

Fein BSS 2.0 E Repair instructions

Baileigh Industrial

Baileigh Industrial SS-2725 Operator's manual

Milwaukee

Milwaukee 2674-20 Operator's manual

Fein

Fein BLs 1.6 parts list

Princess

Princess Electric Multi Sharpener user manual

FOREDOM

FOREDOM K.1050 Operation & maintenance manual