Festivo 75 CFO User manual
Refrigerator-freezer 75 CFO and 75 CFF
Installation and operation manual
Rev 062023
Rev 082023
3EN
Table of Contents
Intended use 4
Models 4
Acceptance 4
Before using the appliance 4
Precautions 5
Installation 6
Operation principle of the appliance 10
Switches and thermostats 10
Switching on 10
Switching off 11
Temperature adjustment: refrigerator and freezer 11
Temperature control: NOLLA drawer 12
Button lock and unlock 12
Freezing 13
Automatic defrosting 13
Manual additional defrost function 13
Normal sounds of the appliance 14
Storing goods 15
Cleaning 18
User maintenance 21
Malfunctions and repairing small faults 22
Error messages 23
Service 24
Warranty conditions 25
Decommissioning the appliance 25
Notes 26
4
EN
Intended use
Festivo refrigeration appliances are suited to refrigerating and freezing food.
The appliances are intended for domestic use.
Festivo refrigeration appliances have been designed and tested in accordance
with the rules and regulations in force.
Festivo refrigeration appliances can be serviced only by an authorized
service center. Repairs by unqualified persons can endanger the user of the
appliance or the environment.
Models
The appliance models in the instruction manual are the refrigerator-freezer
75 CFO and 75 CFF. In the lower part of the refrigerator there is a KYLMÄ drawer. Depending on the model, the
drawers below the refrigerator are either a freezer + NOLLA (75 CF0) or two freezer drawers (75 CFF).
Note!
The equipment and accessories in the instruction manual pictures are not necessarily standard
equipment of the appliance(s).
Acceptance
Check the appliance before accepting it. In case you detect damages in transit to the appliance please note it
down into the transport document, and inform the shipment company and seller immediately.
Note!
The manufacturer’s warranty does not cover damages in transit!
Before using the appliance
Read the installation and operating manual carefully. It includes important information about the installation, use
and maintenance of the appliance.
Do not start to use the appliance immediately after transportation or after it has been kept in a cold place, but let
it stand in its final location for a few hours so that the oil has time to flow down into the compressor.
KYLMÄ
75 CFO 75 CFF
FREEZER
NOLLA
FREEZER
FREEZER
5EN
Precautions
The fridge-freezer must be attached to the wall with an angle plate (A) on
the top of the cabinet or prevent the appliance of falling over in another
manner. If the angle plate does not reach the wall use a suitable connecting
piece for it. The wall mounting screw and plug Ø 6 mm (B) are taped to the
inside of the device.
Before cleaning, turn off the appliance from the power switch and unplug it
from the socket.
Leave the doors open when the appliance is not in use.
Alcoholic substances and conserves containing alcohol e.g. gherkins, pickled
beetroot and lingonberry puree must be stored upright in a tightly sealed
container.
Do not store opened sparkling wine bottles in the door locker, because of
the movement of opening the door can loosen the bottle cork with a lot of
pressure and it can cause damage with its trajectory.
Do not store glass bottles with freezing liquids in the freezer. The bottle can
break. Do not store explosive substances in the refrigerator freezer.
Warning!
It is not allowed to install the appliance in a space that is too small because of possible leakage of
refrigerant forming an explosive mixture of gas. The room size should be at
least 8 m².
The appliance contains a small amount of environmentally friendly but flammable
refrigerant R600, which does not damage the ozone layer or cause greenhouse
effect. Check the refrigerant piping for damages in transit or during installation.
Leaking refrigerant can injure eyes or ignite.
When noticing a refrigerant leakage:
• do not let open fire into the room
• turn off power to the appliance from the main switch
• unplug the appliance from the socket
• air the room for several minutes
• contact the Festivo service center
Note!
Keep the air circulation vents free of obstacles both up and down.
Do not use mechanical tools to speed up melting the ice or other than recommended methods by the
manufacturer.
Do not damage the refrigerant piping.
Do not use any electrical equipment inside the refrigerator freezer unless it is recommended by the manufacturer.
The refrigerator freezer must be fastened to a wall following instructions on page 4.
B
A
6
EN
Installation
PLACEMENT
The intended environmental temperature classification has been indicated on the appliance nameplate. The
nameplate is situated on the right inner wall of the refrigerator.
Place the appliance in a dry and well ventilated room with a size of at least 8 m².
Do not place the appliance in the immediate proximity of a radiator, stove, or an other heat source.
Proper functioning of the refrigerator engine requires a good air circulation.The air circulation vent at the front of
the appliance should not be covered.
Note!
Manufacturer’s warranty does not cover damages that are caused by faulty installation. Check that
the cooling air circulation meets at least the instruction requirement.
The placement floor must be even, horizontal, and at the same level with the finished floor.
Frost, that is formed in the refrigerator evaporator, will be defrosted automatically by the appliance. Melt water is
lead to an evaporation dish in the compressor space. Water evaporates from the evaporation vessel automatically.
In the case of a malfunction of the unit some water can be spilled onto the floor.
Note!
Always place a safety container under the unit.
If the refrigeration assembly includes several appliance modules, install a module wide safety container under
each unit. The picture shows an example of a 120 CFM refrigerator freezer safety container assembly. The safety
container is available as additional equipment.
Alternatively, the location of the refrigerator freezer can be made watertight in other ways. A watertight base
will be raised up onto the wall so that the possible leakage water cannot enter the structure via the floor or wall
joints.
SN +10 ... +32 °C
N +16 ... +32 °C
ST +18 ... +32 °C
T +18 ... +43 °C
7EN
Check that the plastic evaporation basin on top of the compressor is
properly in place. Move the dish to its position if it has been misplaced in
transit.
Other furniture should not be fastened to the refrigerator freezer. One
should be able to pull it out for cleaning and maintenance.
INSTALLATION DISTANCES FROM OTHER DEVICES AND SURFACES
Note!
For more detailed installation dimensions and methods, see a separate installation manual that can be
downloaded address www.festivo.fi the product information of the device in question.
The refrigerator freezer can be placed touching the surfaces on the back and sides. In case the Festivo appliance’s
side surface is next to another cooling unit or outer wall, a ventilation gap of 10 mm width should be left in
between the surfaces.
If the appliance is installed next to a wall it should be off the wall with at least 35 mm gap, so that the door
opens sufficiently and the drawers can slide freely out from inside the cabinet.
When opening, the door corner crosses the outside line of the device. If the front surface of the door of the
appliance is on the same level as the outer surface of the cabinet, leave a minimum gap of 5 mm between the
hinge side of the appliance and the cabinet.
If a full deep upper cabinet is installed above the appliance, at least 40 mm of empty air circulation shall be left
between the appliance and the upper cabinet (1). If the top cabinet is immediately above the appliance, at least
80 mm of empty space shall be left behind and above the cabinet (2). There must be at least 80 mm of empty
space between the freestanding device and the ceiling of the room (3).
1. 2. 3.
8
EN
ELECTRICAL CONNECTIONS
Connect the refrigerator-freezer power cords and both refrigerator freezer power cords to a single phase
230 V 50 Hz socket. The socket fuse size is 10 A.
Only a electrician is allowed to make changes to the plugs change the power cord.
A suitable socket is a socket on the back surface at a height of 2060 mm measured from the floor surface until
the bottom edge of the socket. The socket can be in the ceiling at similar height and at a maximum of 500 mm
from the back wall.
The socket must be positioned in such a way that it is possible to pull the appliance’s plug from the socket
without having to move it.
The extra power cord cannot be pushed behind the furniture into the condeser space but it has to be left on top
of the refrigerator freezer.
Due to danger of overheating the appliance should not be connected to the power grid by means of a branch
outlet or an extension cord.
BALANCING AND LOCKING THE WHEELS
Please check that the wheel locking screws
C of are open.
Push the appliance to its place. Install it
to the same level as the rest of the floor
surface.
Straighten the appliance with the adjusting
screws A (2 pcs) and tighten the locking
screws C. The work requires a 10 mm
spanner.
If the appliance tilts towards the back
even if the adjusting screws A have been
completely loosened it’s necessary to place
sheet material under the back wheels to
heighten the back edge.
INSTALLING FRONT PANEL OF THE PLINTH
Mount the front panel of the plinth to its place. The front panel is attached to the plinth with two fasteners B (2
pcs). When you have pressed the front panel in its place, lift it upwards as far as it lifts.
FALL PREVENTION
Fasten the furniture to the wall with the angle plate on top of the
cabinet and prevent otherwise the appliance from falling over by
accident.
C
B
A
9EN
FITTING THE SHELVES
As a standard there is 3 glass shelves and 1 half glass shelf. The
wire shelves are to be fitted so that the raised edge is towards
the back. The bottle racks are to be fitted so that they hang down
under the shelf.
DOOR ADJUSTMENT
During the initial installation of a new device, there is usually
no need to adjust the doors, because the doors are adjusted at
the factory. If the doors need to be adjusted when connecting
the devices, it may be due to the unevenness of the floor. Small
unevenness in the floor can be corrected with the adjustment
screws on the base of the device.
Check the position of the door in relation to the frame. If the door
is not straight, it can be adjusted with hinges.
Horizontal adjustment, photo 1
Loosen the screws of the upper hinge. Turn the hinge in a sideways
direction (arrows C) until the upper edges of the doors are at the
same level, and tighten the screws.
Dimension A (photo 3) must be same both up and down. If it is not,
move the upper hinge in B arrows direction.
Lower hinge, photo 2
Lower hinge can be adjusted horizontally.
Check the seals of the doors. If it is too compressed, move the
upper hinge outwards.
If the seal has become pressed down, warm it CAREFULLY with a
hot-air blower (hair dryer) and mould it with the fingers to make it
higher.
Warning!
Before the cover will be released, the voltage of the
appliance must be switched off. Also the plug of the
appliance must be taken out of the socket.
Lubricate hinges if necessary.
Bottom hinge, picture 2
Top hinge, picture 1
Picture 3
A
A
10
EN
Operation principle of the appliance
The cooling system, consisting of a compressor (K), a condenser (L) and an evaporator
(H), operate as a closed circuit, where the compressor circulates the refrigerant.
In the evaporator the refrigerant vaporizes and absorbs heat, cooling the refrigerator
and the freezer.
The heat, bound to the refrigerant, is transferred into the surrounding air via the
condenser.
Any ice formed in the evaporator melts automatically and melt water will be lead into
an evaporation dish in the compressor space, where it will evaporate automatically.
Switches and thermostats
4 3 2 1
1. Main switch (switches the voltage for the appliance)
2. Freezer temperature control
3. Refrigerator temperature control
4. Door switch
Switching on
Do not start to use the appliance immediately after transportation or after it has been kept in a cold place, but let
it stand in its final location for a few hours so that the oil has time to flow down into the compressor.
Before using the appliance, clean its interior parts (see the chapter on “Cleaning”)
Push the plug on the connecting lead of the appliance into the electric socket.
Do not place food into the appliance before the temperatures in the refrigerator and freezer have reached their
set values.
At the factory, the main switch of the appliance (1) was left in the OFF position.
Push the main switch (1) and then within 10 seconds the temperature of the refrigerator will appear on the
display.
Inside temperatures of the appliance can be monitored from the controller display.
K
L
H
H
This manual suits for next models
1
Table of contents
Other Festivo Refrigerator manuals
