Fein GWP10 Setup guide
GWP 10
Repair instructions
C-SC_CSSM
Version 1.0
2016-02-02
All rights reserved by FEIN, especially in case of property rights applications.
FEIN retains all rights of disposal, such as copying and circulation.
Page 1of 39
GWP 10
Contents
C-SC_CSSM
Version 1.0
2016-02-02
All rights reserved by FEIN, especially in case of property rights applications.
FEIN retains all rights of disposal, such as copying and circulation.
Page 2of 39
1. Models described
2. Technical data
3. Notes and requirements
4. Tools required
5. Lubricants and auxiliary substances required
6. Removal
7. Fitting
8. Connection diagram
GWP 10
1. Models described
C-SC_CSSM
Version 1.0
2016-02-02
All rights reserved by FEIN, especially in case of property rights applications.
FEIN retains all rights of disposal, such as copying and circulation.
Page 3of 39
These repair instructions describe how to repair the following models:
Model Order number
GWP 10 7 209 38 .. .. .
GWP 10
2. Technical data
C-SC_CSSM
Version 1.0
2016-02-02
All rights reserved by FEIN, especially in case of property rights applications.
FEIN retains all rights of disposal, such as copying and circulation.
Page 4of 39
Technical data
All the technical data can be found in the operating instructions for the model.
Test data
Up-to-date test data for all models can be found on the FEIN Extranet (Customer Service →Repair Guides).
Lubricants
The lubricants and container sizes available from FEIN can be found on the FEIN Extranet (Customer Service →Repair Guides).
Lists of spare parts
Lists of spare parts and exploded views are available online at www.fein.com
GWP 10
3. Notes and requirements
C-SC_CSSM
Version 1.0
2016-02-02
All rights reserved by FEIN, especially in case of property rights applications.
FEIN retains all rights of disposal, such as copying and circulation.
Page 5of 39
Please note
These instructions are only intended for persons with suitable technical training. It is assumed that the reader has mechanical and
electrical training.
Only use original FEIN spare parts.
Provisions
Please note that power tools may only be repaired, maintained and checked by a trained electrician, as improper repair can result in
serious risks to the user.
The provisions set out in DIN VDE 0701-0702 should be observed after repairs.
The relevant accident prevention regulations of the employer’s liability insurance associations are to be observed when
commissioning.
The German Equipment and Product Safety Act [ProdSG] applies for correct use.
Outside Germany, the regulations applicable in the relevant country must be observed.
GWP 10
4. Tools required
C-SC_CSSM
Version 1.0
2016-02-02
All rights reserved by FEIN, especially in case of property rights applications.
FEIN retains all rights of disposal, such as copying and circulation.
Page 6of 39
Standard tools
Special tools
Torx T20 Assembly aid 6 41 22 121 01 0
Cross-tip screwdriver PH1, PH2 Expansion wedge, 12 mm 6 33 05 009 01 3
Slotted screwdriver (small) Drawing-off socket cap 6 41 04 150 00 8
Combination pliers Chuck cone with 16 mm diameter 6 41 07 016 00 1
Plastic hammer Chuck cone with 17 mm diameter 6 41 07 017 00 0
Arbor press Chuck cone with 19 mm diameter 6 41 07 019 00 7
Punch 5 mm; 6 mm; 9 mm
Long-nosed pliers
Slide hammer
Inner puller
Sleeve 11 mm inner diameter
26 mm outer diameter
7 mm inner diameter
30 mm outer diameter
19 mm inner diameter
30 mm outer diameter
~16 mm inner diameter
19 mm outer diameter
8 mm inner diameter
~17 mm outer diameter
GWP 10
4. Tools required
C-SC_CSSM
Version 1.0
2016-02-02
All rights reserved by FEIN, especially in case of property rights applications.
FEIN retains all rights of disposal, such as copying and circulation.
Page 7of 39
Standard tools
Sleeve 8 mm inner diameter
~19 mm outer diameter
GWP 10
5. Lubricants and auxiliary substances required
C-SC_CSSM
Version 1.0
2016-02-02
All rights reserved by FEIN, especially in case of property rights applications.
FEIN retains all rights of disposal, such as copying and circulation.
Page 8of 39
Lubricants
Grease 0 40 101 0100 4 25 g Housing
GWP 10
6. Removal
C-SC_CSSM
Version 1.0
2016-02-02
All rights reserved by FEIN, especially in case of property rights applications.
FEIN retains all rights of disposal, such as copying and circulation.
Page 9of 39
Removing the handle half shell
1. Unscrew the countersunk screw (1).
2. Remove the switch pushbutton (2).
3. Unscrew the three screws (3).
4. Remove the handle half shell (4).
Tools:
- PH1 cross-tip
screwdriver
- PH2 cross-tip
screwdriver
2
1
4
3
GWP 10
6. Removal
C-SC_CSSM
Version 1.0
2016-02-02
All rights reserved by FEIN, especially in case of property rights applications.
FEIN retains all rights of disposal, such as copying and circulation.
Page 10 of 39
Removing the handle half shell
1. Unscrew the screw (1).
2. Remove the cable clamping piece (2).
3. Remove the cover (3).
4. Remove the handle half shell (4).
Tools:
- PH2 cross-tip
screwdriver
3
2
1
4
Other manuals for GWP10
1
This manual suits for next models
1
Table of contents
Other Fein Drill manuals
Fein
Fein DSc 636 User manual
Fein
Fein ABH 18 Series User manual
Fein
Fein KBH25 User manual
Fein
Fein kbb38x Setup guide
Fein
Fein ABS18 Q User manual
Fein
Fein ASzx 648 User manual
Fein
Fein ASye 636 Kin Quick start guide
Fein
Fein KBH25-2U Series User manual
Fein
Fein 7 205 43 User manual
Fein
Fein BOP6 User manual
Fein
Fein Tapper ASge 636 User manual
Fein
Fein ASze 648a Quick start guide
Fein
Fein KBB 40 Series User manual
Fein
Fein KBM 32Q User manual
Fein
Fein KBM80U User manual
Fein
Fein KBU 110-4 M Setup guide
Fein
Fein HandyMaster ASB 14V User manual
Fein
Fein 7 270 27 User manual
Fein
Fein KBM 50 Q User manual
Fein
Fein KBB60X User manual
