F&U FL-16101 User manual
By AMIRIDIS – SAVVIDIS S.A.
15.6" Wide Screen LED TV
MODEL:FL-16101
Instruction Manual
Read all of the instructions before using this TV and keep the
instruction manual in a safe place for future reference.
Contents
Caution
Safety Information
Accessories
Technical Specification
Product Introduction
Front View
Intall the TV Base
OSD Menu
1. Picture menu
2. Sound menu
3. Channel menu
4. Feature menu
Multimedia Operation
2
3
4
4
4-5
6-11
4
5
17-55
17
18
19-25
26-46
5. Setup menu 47-50
51-55
Connections
12-13
Remote Control
14
Basic Operation
14-16
Auto Installation
56-57
58
USB MULTIMEDIA PLAYBACK FORMAT
Simple Troubleshooting
59SPECIFICTIONS
-- 1 --
!
"#
$$
!
"
""#
Safety Information
WARNING: The battery (battery or batteries or battery pack) shall not be exposed to excessive heat such as sunshine, fire or
the like.
WARNING: Excessive sound pressure from earphones and headphones can cause hearing loss.
Accessories
User’s Manual Adapter Warranty card AAA Batteries
Warranty card
Remote control
* Note: The configuration of the components may look different from the following illustration
Technical Specification
PAL(B/G,D/K,I) SECAM(B/G,D/K)
15.6 inch(diagonal)
1366x768
2x3W
12V 3A
- TV System
- Screen Size
- Resolution
- Aerial input
- Audio output power
- Power Consumption
Remote Control
Type
Control distance
Control angle
Batteries
0
infrared
5m
30 (horizontal)
2 x 1.5V, size AAA
Recommended USB standard USB2.0
USB file system NTFS FAT16 FAT32(Maximum supported
hard disk size: 1T)
POWER MUTE
PICTURE ASPECT SOUND
SLEEPSUBTITLE CH.LIST
REC.LISTREC
123
456
789
0
VOL CH
INPUTDISPLAY
EPG
TV/RADIO
FAV
MENU
TV/TXT CANCEL REVEAL NICAM/A2
INDEX HOLD SIZE SUBPAGE
EXIT
Product Introduction
Front View
Mini YPbPr cable Mini AV cable
CH+/-: Press to scan through channels.
Turn on/standby the TV set.
VOL+/-:
MENU:
Press to display the input source
menu.
INPUT:
POWER:
Remote Control window
INPUT
MENU
CH-
CH+
VOL-
VOL+
POWER
Product Introduction
Install the TV Base
3. Warnings.
1. The parts needed for installing the stand (supplied)
TV set Stand Screws(supplied)
4 x ST3 x 10F
2. How to install the Stand?
Back
Front
Before installing the stand, please check that
you have all of the parts and that there is no
visible damage. If a part is missing or appears
damaged, please contact customer service.
Put the Stand to the neck of the TV set as shown below, Please pay close attention to the plunger and slots.
1. Before you put on the stand, please make sure the direction is correct
as shown below.
2. When you are putting on the stand, please make sure the neck of the
TV set is in the correct position and attached tightly.
If you do not attach the stand correctly, it will make the TV unstable
and may tip over.
Place the TV face down on a soft and flat surface (blanket, foam, cloth, etc.) to prevent any damage to the TV.
Attach the stand with the supplied screws.
When attaching the stand, make sure the screws
are attached tightly.
If the screws do not attach tightly, it will lead the TV
to be unstable or may even tip over.
b. It can not be tilted to the right or left as shown below.
Doing so may damage the stand.
a. It can not be tilted to the front or back as
shown below. Doing so may damage the
stand.
Connections
RF: Connect antenna or cable 75 Ohm coaxial to receive TV signal.
COAX:Connects to the audio jack on the digital/standard 5.1 audio system.
YPbPr: Connects to the DVD player,Digital Set-Top-Box,or other AV equipment
AV: Connects the Video output jack of DVD or VCR.
USB: Allows access to digital ontent stored on a USB storage device.
Headphone: Connect it to your headphone or other audio equipment.
Insert the CI card into the slot.
HDMI: Connect it to the HDMI of DVD or other equipment.
VGA:
For PC display.Connect it to the D-Sub 15 pins analog output connector of the PC.
Connect to the power adaptor.
PC-IN: Connect it to the audio output terminal of PC.
SCART:
Connect to extermal equipment with SCART socket, The SCART interface
offers RGB, AV singals with audio input/output between the TV and extermal video
equipment.
with component (YPBPR) video.
POWER:
COMMON INTERFACE:
COAX
RF
SCARTPC - I NVGAHDMIPOWER
USB COMMON INTERFACE
YPbPr AV
Connection
Connection
Power adaptor Connection
- Connect the power adapt correctly as shown with the mains cable.
- When you connect the power, the TV set comes into standby mode and the LED indicator
- You could bring the TV out of standby mode by press the ortesVTnonottuPOWER b
remote control, and the LED indicator lights green.
Antenna(RF) Connection
RF
Coaxial (Round) Antenna Cable
Press button on the remote control to display the input source menu, press
button to select ATV/DTV, then press OK
Wall jack with F-Connector
External Antenna
INPUT
lights red.
COAX
RF
SCARTPC - I NVGAHDMIPOWER
Connection
AV Input Connection
Note: All cables shown are not included with the TV.
- Connect the VIDEO and AUDIO output jacks on the DVD or VCR to the AV IN jacks on
- Match the jacks colors: Video=yellow, Audio left=White, Audio right=red.
- Turn on the DVD/VCR, and select “AV” in the input source menu.
RCA Video&Audio Cabl e
DVD or VCR
HDMI Connection
Note: All cables shown are not included with the TV.
DVD or VCR
- Connect the HDMI jack on the DVD to the HDMI jack on the TV set with a HDMI cable.
- Turn on the DVD, and select “HDMI” in the input source menu.
A/V
interface that supports uncompressed standard. One jack supports both video and audio
information.
the TV set with a RCA cable.
Audio_L
Audio_R
GND
CVBS
AV-IN
USB COMMON INTERFACE
YPbPr AV
COAX
RF
SCARTPC-INVGAHDMIPOWER
Table of contents
Other F&U LED TV manuals
