Falconeyes FT-200FA User manual
IM1101_FT-FA_eng
E) Attentions
Instruction Manual
3
D) Specification
FT-FA Series
Studio Flash
FT-200FA / FT-300FA / FT-400FA
FT-600FA / FT-800FA / FT-1000FA / FT-1200FA
Since there could be high voltage inside the unit, please DO NOT
open or repair the unit yourself. If there is any defect, please contact
the experienced technician.
Avoid strong light directing to the photo sensor.
Please ensure the power is switched off after use.
Power Range
Modeling
Power Control
Guide No.(ISO100/m)
Recycle Time
Angle of Illumination
Color Temperature
Operating Voltage
AC 110-120 60Hz/AC 220-240 50Hz
Triggering
Accessories Included Reflector,Power Cord, Sync Cord, Modeling Lamp
Optional Accessories Softbox, Barndoor ,honeycomb , Color Filter Set, Snoot, Light Stand, Umbrella etc.
Model No.
400Ws300Ws 600Ws 800Ws 1000Ws 1200Ws
FT-300FA FT-400FA FT-600FA FT-800FA FT-1000FA FT-1200FA
150W 150W 250W 250W 250W 250W
5500K - 5800K
≥55°
1/32~1, ( Stepless )
55 64 78 90 95 100
1~2s
200Ws
FT-200FA
150W
45
1~1.5s 1~2s 1~2s 1~4s 1~4s 1~4s
Photo Sensor, Sync Cord, Test Button
Do not remove the flash tube until the light is switched off for at least
10 minutes in order to avoid scald.
For better maintenance, if the unit has been triggered continuously 10
times in a short period please leave the unit dormant 2 minutes.
A) Features
1 2
This is a stable and quick rechargeable studio flash system. Its power
is variable from 1/32 to 1. Its capacitor can discharge automatically when
it is not in use. The brightness of the modeling lamp is directly
proportional to that of the flash tube, so that you can preview the lighting
effect before taking the pictures. Besides, it contains a perfect notification
design for fully-charged and over-heat condition. When it is fully charged,
it will buzz and the indicator will be on as green. FT-FA series signifies the
most durable, user-friendly and professional oriented.
B) Panel Diagram
C) Instructions
Beeper On/Off Switch
Modeling Lamp
Mode Switch
Modeling Lamp
ON/OFF Switch
Test Button
Main Power
On/Off Switch
Sync Socket
Ready Lamp
Fuse
Power Socket
Power Control Dial
Photo Sensor
On/Off Switch
Photo Sensor
i)
ii)
iii)
iv)
v)
vi)
vii)
viii)
Connect to the power supply. Turn on the lighting unit and the
modeling lamp. (The brightness of the flash tube and the modeling
lamp is adjustable and the lighting effect is directly proportional to
each other.) If there is no need to control the brightness, you can just
turn on the flash. When the buzzer stops buzzing which means the
capacitor is fully charged, the flash can then be controlled to spark.
The illuminating angle of the flash unit can be adjusted. The result of
shooting can be previewed by using the modeling lamps.
This flash unit is thermo sensitive. When the temperature is higher
than the safety standard (Indicator light will turn to green), the flash
will be shut down. Once it is cooled down, the flash will function
again. Its purpose is to prevent the damage from overheat.
The guide number is directly proportional to the brightness of the
flash. The stepless power control can be adjusted from 1/32 to full
power for different luminosity of flash and modeling lamp. When
changed from high power to low power, the unit will flash once
automatically.
There is a sync cord included in the package, which one end is
connected to the flash unit and the other end is connected to the
camera.
Buzzer On/Off Switch can turn the buzzing function on. When it is
on, it will buzz until the capacitor is fully recharged.
The reflector is changeable. To change it, please press a button
down which is on the peripheral of the housing and turn the reflector
anticlockwise. Then, it can be removed.
If the umbrella reflector is used, please insert the stem into the
umbrella installation hole which is at the bottom of the flash housing.
Then, tighten the screw of the knob.
This manual suits for next models
6
Other Falconeyes Flashlight manuals
