FAHRBIKE CRUZ User manual
www.fahrbike.com
OWNER’S MANUAL
FAHRBIKE-CRUZ
Contents
Assembly 07
Handlebars 07
Pedals 10
Seat 11
Front Wheel 08
Bottle Holder 11
Battery Care 13
Battery Charging 13
Removing the Battery 12
Brake Lever Adjustment 11
Disclaimer 04
Product Specification 05
General Information 04
Introduction 01
Safety Check 02
Tire Pressure 09
Rear Wheel 09
Walk Mode 16
Data Mode 16
Cleaning 19
Tips 20
Settings Mode 17
Serial Number 21
Warranty 22
Legal Requirements 21
14
Battery Storage
Power Assist Level 15
LCD Display 15
Switch Power ON / OFF 15
Headlight and Taillight 16
Throttle and Cruise Control 15
Error Code Definition 18
Fender 09
Maintenance 19
Congratulations on the purchase of your Fahrbike! You have chosen a bike that will give you an unparalleled
riding experience and you have made a wise choice.
Please read this Owner's Manual carefully before using your new e-bike. It is your reference for assembly,
maintenance, and safety.
If you are not confident in assembling the bike yourself, we strongly recommend that you have your bike
assembled by a qualified bicycle mechanic.
If you have questions or need assistance, please contact us directly.
Official Website: www.fahrbike.com
Email: service@fahrbike.com
Introduction
01 FAHRBIKE-CRUZ
Safety Check
02
1
FAHRBIKE-CRUZ
Please check the following components: Handlebars, stem, pedals, crank arms, and wheels. Make sure they
are properly assembled and tightened. Even if some of the components are pre-assembled, each part must be
tightened to the specified torque. If you do not notice a loose component, it may come loose during use and
cause serious injury.
It is recommended that the above safety checks be performed every 200 - 300 km (120 - 180 miles) or when
the bicycle has not been used for three weeks.
Wheels: An important part of assembling your bike is attaching the front and rear wheels and checking
that the wheel axle nuts are tight. Properly assembled wheels are essential for the safe use of the bicycle.
Tires: Both tires must be inflated according to the specifications in the manual. Failure to do so will reduce
performance, increase tire wear, and compromise your safety.
Crank and pedals: Make sure the crank arms and pedals are tightened to the specified torque. A required
tool for the crank: 8 mm hex key, recommended tightening torque 30-35 Nm. Required tool for the pedals:
15 mm wrench, recommended torque 35-40 Nm.
Brakes: Make sure the brakes are working properly and are properly secured. When braking, apply the rear
brake first, then the front brake. Incorrect application of the brakes can result in serious injury.
Throttle: The throttle mechanism can be used to partially or fully activate the engine power. Inexperienced
users should be a bit more careful when operating the throttle for the first time. The throttle function is
deactivated when the pedal assistance is set to "0".
03
Users must familiarize themselves with the power controls before riding. It is strongly recommended that you
ride your new bike in an open area and set the assist level to "0". Once you become accustomed to operating
your bike, gradually increase the assistance level.
It is good practice to keep your hands over the brake levers. The brake levers are equipped with motor pro-
tectors that shut off motor power when activated. If you lose control for any reason, immediately apply the
brake levers to shut off motor power. Do not attempt to stop your bike with your feet as this may cause you
to lose your balance.
When walking or carrying your bike, turn off the power to avoid accidentally turning on the motor. If the
motor is accidentally turned on, immediately apply the brakes to cut the power to the motor.
For Your Safety
FAHRBIKE-CRUZ
General Information
04
2
FAHRBIKE-CRUZ
The use of an e-bike involves risks, and it is the user's responsibility to understand those risks. You are respon-
sible for your own actions when using an electric bike. Fahrbike is not responsible or liable for any accidents
or injuries (whether caused by you or others) that may occur during use. We recommend that you contact
your insurance company to find out whether or not your current insurance policy covers you in the event of
an accident.
Disclaimer
Product Specification
05
3
Battery
Motor
Display
Speed
Pedal
Crankset
Recommended
Rider Heights
48V, 720Wh
500W Geared Brushless Motor
LCD Display
24MPH
Wellgo Aluminum Platform
42T Single Guard
Available in 15”/17”/19”
Sizes for Riders 4'11" to 6'2"
Tall
SR Suntour with Lockout
Step-through 6061 Aluminum
Alloy Frame
Hydraulic Disc Brakes, 180mm
Rotors
Nickel Plated 11-32T 8-speed
Shimano Rapid Fire Plus
8-Speed
65 lbs
27.5" x 2.1" Kenda Tire
Front Fork
Brake
Bike Frame
Freewheel
Shifter
Tires
Product Weight
FAHRBIKE-CRUZ
06FAHRBIKE-CRUZ
Assembly
(A)Handlebars (required tools: 4mm hex key, 5mm hex key)
Unscrew the retainer from the head tube.
Remove the silver spacers from the head tube.
Insert the handlebar stem into the head tube.
Fold the handlebar by opening the lever.
Insert the retainer into the head tube and tighten (recommended tightening torque 8 Nm).
Unfold the handlebar by closing the lever.
Align the handlebar with the front wheel and tighten the two bolts on the side of the stem (recommended
tightening torque 12 Nm).
07
4
FAHRBIKE-CRUZ
(B)Front Wheel
Remove the brake pad protector between the brake pads.
Install the wheel by sliding the disk brake rotor between the brake pads and inserting the fork end onto
the wheel axle.
Remove the nut and spring (A) from the quick-release skewer.
Insert the quick release skewer with spring (B) pointing inward into the right side of the wheel axle.
Insert spring (A) pointing inward into the left side of the quick release skewer and tighten the nut.
Close the quick release lever and tighten it by turning clockwise.
08FAHRBIKE-CRUZ
Table of contents
Other FAHRBIKE Bicycle manuals
