Faber Veil User manual

Libretto di Istruzioni

Instructions Manual

Bedienungsanleitung

Manual de instrucciones

Instrukcja Obsâugi

ɋɮɥɩɝɩɟɬɭɝɩ ɪɩ ɸɥɬɪɦɮɛɭɛɱɣɣ

ǽȗȥıțȢȔİțȡ ȡİșȗțȬȟ

Käyttöohje

Brugsvejledning

Bruksanvisnin

Priroÿnik za uporabo

Príruÿka na obsluhu

Uputstva za Korištenje

Uživatelská Pøíruèka

Ƀɨɬɭɫɮɥɱɣɣ ɋɵɥɩɝɩɟɬɭɝɩ

ΐϴϛήΘϟ΍ Ϟϴϟ

EN 1

RECOMMENDATIONS AND SUGGESTIONS

The Instructions for Use apply to several versions of this appliance.

Accordingly, you may find descriptions of individual features that do not

apply to your specific appliance.

INSTALLATION

! The manufacturer will not be held liable for any damages resulting from

incorrect or improper installation.

! The minimum safety distance between the cooker top

and the extractor hood is 650 mm (some models can

be installed at a lower height, please refer to the

paragraphs on working dimensions and installation).

! Check that the mains voltage corresponds to that

indicated on the rating plate fixed to the inside of the

hood.

! For Class I appliances, check that the domestic

power supply guarantees adequate earthing.

Connect the extractor to the exhaust flue through a pipe of minimum

diameter 120 mm. The route of the flue must be as short as possible.

! Do not connect the extractor hood to exhaust ducts carrying combustion

fumes (boilers, fireplaces, etc.).

! If the extractor is used in conjunction with non-

electrical appliances (e.g. gas burning

appliances), a sufficient degree of aeration must

be guaranteed in the room in order to prevent the

backflow of exhaust gas. The kitchen must have

an opening communicating directly with the open

air in order to guarantee the entry of clean air.

When the cooker hood is used in conjunction with

appliances supplied with energy other than electric, the negative pressure in

the room must not exceed 0,04 mbar to prevent fumes being drawn back

into the room by the cooker hood.

! In the event of damage to the power cable, it must be replaced by the

manufacturer or by the technical service department, in order to prevent any

risks.

2°

EN 1

• If the instructions for installation for the gas hob specify a greater distance

specified above, this has to be taken into account. Regulations concerning

the discharge of air have to be fulfilled.

• Use only screws and small parts in support of the hood.

Warning: Failure to install the screws or fixing device in accordance with

these instructions may result in electrical hazards.

• Connect the hood to the mains through a two-pole switch having a contact

gap of at least 3 mm.

USE

• The extractor hood has been designed exclusively for domestic use to

eliminate kitchen smells.

• Never use the hood for purposes other than for which it has been designed.

• Never leave high naked flames under the hood when it is in operation.

• Adjust the flame intensity to direct it onto the bottom of the pan only, making

sure that it does not engulf the sides.

• Deep fat fryers must be continuously monitored

during use: overheated oil can burst into flames.

• Do not flambè under the range hood; risk of fire.

• This appliance can be used by children aged from

8 years and above and persons with reduced

physical, sensory or mental capabilities or lack of

experience and knowledge if they have been given supervision or instruction

concerning use of the appliance in a safe way and understand the hazards

involved. Children shall not play with the appliance. Cleaning and user

maintenance shall not be made by children without supervision.

EN 1

• •CAUTION: Accessible parts may become hot when used with cooking

appliances.”

MAINTENANCE

•Switch off or unplug the appliance from the mains supply before carrying out

any maintenance work.

• Clean and/or replace the Filters after the specified time period (Fire hazard).

• The Grease filters must be cleaned every 2 months of operation, or more

frequently for particularly heavy usage, and can be washed in a dishwasher.

• The Activated charcoal filter is not washable and cannot be regenerated,

and must be replaced approximately every 4 months of operation, or more

frequently for particularly heavy usage.

• Clean the hood using a damp cloth and a neutral liquid detergent.

The symbol on the product or on its packaging indicates that this product

may not be treated as household waste. Instead it shall be handed over to the

applicable collection point for the recycling of electrical and electronic

equipment. By ensuring this product is disposed of correctly, you will help

prevent potential negative consequences for the environment and human

health, which could otherwise be caused by inappropriate waste handling of

this product. For more detailed information about recycling of this product,

please contact your local city office, your household waste disposal service or

the shop where you purchased the product.

EN 1

CHARACTERISTICS

Dimensions

Components

Ref. Q.ty Product Components

1 1 Hood Canopy complete with: Controls, Light, Fan

unit, Filters

21 Telescopic chimney, made up of:

2.1 1 Upper Chimney

2.2 1 Lower Chimney

81 Air outlet grid D.150

91 Damper D.150-120

14 1 Hood Canopy Air Outlet Extension made up of 2

half-elements

Ref. Q.ty Installation Components

11 6 Wall Plugs

11a 2 SB 12/10 Wall Plugs

12a 6 Screws 4.2x44.4

12c 4 Screws 2.9x9.5

12e 4 Screws 2.9x6.5

Q.ty Documentation

1 Instruction Manual

EN 1

INSTALLATION

Drilling the Wall and Fixing the Brackets

650

455

240 240

200 200

Draw the following on the Wall:

• a Vertical line up to the ceiling or top surface, at the centre of the area in which the Hood is

to be fitted;

• a Horizontal line: 650 mm min. above the Hob;

• As shown in the drawing, mark a reference point 455 mm above the reference horizontal

line, and at a distance of 240 mm to the right of the vertical reference line.

• Repeat this operation on the other side, checking to ensure it is level.

• Drill the points marked using a ø 12 mm drill bit.

• Insert the wall plugs with screw and bracket 11a into the holes, tighten.

• As shown in the drawing, mark a reference point 75 mm above the reference horizontal line,

and at a distance of 200 mm to the right of the vertical reference line.

• Repeat this operation on the other side, checking to ensure it is level.

• Drill the points marked using a ø 8 mm drill bit.

• Insert the plugs 11 into the holes.

• Rest the Bracket 7.2.1 as indicated, 1-2 mm from the ceiling or surface above the hood, aligning

its centre (grooves) with the vertical reference line.

• Mark the centres of the holes in the bracket.

• Rest the Bracket 7.2.1 as indicated, X mm under the first bracket (X = height of the Upper

chimney provided), aligning its centre (grooves) with the vertical reference line.

• Mark the centres of the holes in the bracket.

• Drill the points marked using a ø 8 mm drill bit.

• Insert the plugs 11 into the holes.

• Fix the brackets using the screws 12a (4.2 x 44.4 ) provided.

EN 1

Fitting the Hood canopy

• Remove the Metal grease filter using the handles provided.

• Adjust the two screws Vr, in the brackets 11a, so that they are

at the start of their travel.

• Hook the hood body to the two brackets 11a.

• From the inside of the hood body, turn screws Vr to level the

hood body itself.

• Fasten the safety screws 12a.

• Replace the Metal grease filter.

Connections

AIR OUTLET - DUCTING VERSION

When installing the Ducting version, join the Hood to the outlet

duct using a rigid or flexible pipe ø150 - ø 120 selection of which

is at the discretion of the installation technician.

• Check that the pipe is properly inserted onto the Motor Unit

outlet.

• Fix the outlet pipe using suitable pipe clamps. The materials

required to do so are not provided.

AIR OUTLET – RECIRCULATION VERSION

• Join the 2 half-elements making up the pipe 14.

• Push the pipe 14 firmly until it is all the way in.

• Cut away the excess part with a tool.

• Fix the directional Grid 8 on the recycled air outlet, using 2

screws 12e (2.9 x 9.5) provided.

• Make sure that the Activated charcoal odour filter has been

fitted.

EN 2

Fitting the Chimney

Lift the 2 tabs formed on the Hood Canopy close to the

air outlet opening.

Upper chimney

• Open the two side pieces out slightly, hook them up

behind the brackets 7.2.1 and bring them back

together again until they are in contact.

• Fix them to the sides of the Brackets using 4 Screws

12c (2.9 x 9.5), provided.

Lower chimney

• Open out the two Chimney side flaps, hook them up

between the upper chimney and the wall and then

close them up again until they touch.

• Fix the lower part to the Hood canopy tabs at the

sides, using 2 screws 12c (2.9 x 9.5) provided.

ELECTRICAL CONNECTION

• Connect the hood to the mains through a two-pole

switch having a contact gap of at least 3 mm.

• Remove the grease filters (see paragraph Mainte-

nance) being sure that the connector of the feeding

cable is correctly inserted in the socket placed on the

side of the fan.

EN 2

USE

T1 L

Control panel

BUTTON LED FUNCTIONS

T1 Speed On Turns the Motor on at Speed one.

Turns the Motor off.

T2 Speed On Turns the Motor on at Speed two.

T3 Speed Fixed When pressed briefly, turns the Motor on at Speed three.

Flashing Pressed for 2 Seconds.

Activates Speed four with a timer set to 6 minutes, after which

it returns to the speed that was set previously. Suitable to deal

with maximum levels of cooking fumes.

LLight Turns the Lighting System on and off.

Warning: Button T1 turns the motor off, after first passing to speed one.

EN 2

MAINTENANCE

Grease filters

CLEANING METAL SELF- SUPPORTING GREASE FILTERS

• The filters must be cleaned every 2 months of operation, or

more frequently for particularly heavy usage, and can be

washed in a dishwasher.

• Remove the filters one at a time by pushing them towards the

back of the group and pulling down at the same time.

• Wash the filters, taking care not to bend them. Allow them to

dry before refitting.

• When refitting the filters, make sure that the handle is visible

on the outside.

Activated charcoal filter (Recirculation version)

These filters are not washable and cannot be regenerated, and

must be replaced approximately every 4 months of operation, or

more frequently with heavy usage.

REPLACING THE ACTIVATED CHARCOAL FILTER

• Remove the metal grease filters

• Remove the saturated activated charcoal filter as shown (A).

• Fit the new filters (B).

• Replace the metal grease filters.

Lighting unit

Warning: This appliance is fitted with a white LED lamp classed

as 1M according to EN 60825-1: 1994 + A1:2002 + A2:2001

standards; maximum optical power emitted @439nm: 7µW. Do

not look directly at the light through optical devices (binoculars,

magnifying glasses…).

• For replacement contact technical support. ("To purchase con-

tact technical support")

Other manuals for Veil

Table of contents

Other Faber Ventilation Hood manuals

Faber

Faber AGIO24PR300-B User manual

Faber

Faber CHLOE XL CG MATT A110 User manual

Faber

Faber BELLA EG8 X A60 FB EXP User manual

Faber

Faber MIRROR User manual

Faber

Faber CYLINDRA ISOLA User manual

Faber

Faber INCA HC SS User manual

Faber

Faber 620000041 User manual

Faber

Faber Nova User manual

Faber

Faber Zoom IS 16 SS Owner's manual

Faber

Faber T-Light Isola X A100 User manual

Faber

Faber Diamante DIAM36SS User manual

Faber

Faber Pro Magnum Product information sheet

Faber

Faber FABERJET CLASSO 7644SS User manual

Faber

Faber HEAVEN GLASS 2.0 User manual

Faber

Faber VOLUTE 900 INOX User manual

Faber

Faber DIAMANTE User manual

Faber

Faber T-LIGHT ISOLA WIT MATT A100 User manual

Faber

Faber TRATTO 30 User manual

Faber

Faber HIGH-LIGHT Series Owner's manual

Faber

Faber VRT BK A90 2LS User manual

Faber

Faber FABULA BK RB User manual

Faber

Faber FVMY AH BK F90 User manual

Faber

Faber Diamante Isola User guide

Faber

Faber COCKTAIL User manual

Popular Ventilation Hood manuals by other brands

emmeti

emmeti RECUPA MED A-140 Installation and use manual

Nibe

Nibe F135 user manual

Kuppersberg

Kuppersberg INTRO 60 Technical Passport

Zephyr

Zephyr Spruce AK9834BS Use, care and installation guide

Hisense

Hisense MH6INBG manual

Miele

Miele DA 1255 Operating and installation instructions

Broan

Broan 46000 Specification sheet

GE Profile PV977 Owner's Manual & Installation Instructions

FALMEC

FALMEC FFRIA24W5FS Instruction booklet

Whirlpool

Whirlpool RH2600XL-1 SERIES installation instructions

Küppersbusch

Küppersbusch DX ISLA instruction manual

ETNA

ETNA AV360RVS Instructions for use

JUNO

JUNO JDF603E6 installation manual

Miele

Miele DA 6708 D Operating and installation instructions

Tricity Bendix

Tricity Bendix LE 150 Installation & operating instructions

AEG

AEG X68163BV1 user manual

AEG

AEG 125 D operating instructions

Smeg

Smeg KSEV97X instruction manual