Extron electronics UCS FT 901 User manual

IMPORTANT:

Go to www.extron.com for the complete

user guide, installation instructions, and

specifications before connecting the

product to the power source.

UCS FT 901 and UCS FR 902 • Setup Guide

This guide provides basic instructions for an experienced technician to install and

congure the Extron UCS 900 Series. The UCS FT 901 and UCS FR 902 extend USB

signals from USB 3.x, 2.0, and 1.1 peripheral devices located up to 492 feet (150 meters)

away to a USB 3.x host computer over multimode ber optic cable, with a SuperSpeed

data transfer rate of up to 5 Gbps. The transmitter features a USB Type-C connector.

The receiver features a built-in active two-port hub that supplies up to 5 V, 1.5 A from

each port to power attached devices.

See the UCS FT 901 and UCS FR 902 User Guide, available at www.extron.com, for more information.

NOTES:

• This product supports USB data ONLY. DisplayPort Alt Mode and Power Delivery are NOT supported.

• The use of a USB 2.0 hub on the UCS FR 902 is not recommended. If a hub is needed in the system, Extron

recommends the use of a USB 3.x hub. Please contact your Extron AE for more details.

Installation

ATTENTION:

• Installation and service must be performed by authorized personnel only.

• L’installation et l’entretien doivent être effectués uniquement par un technicien qualifié.

Mounting

The UCS FT 901 and UCS FR 902 can be rack mounted, furniture mounted, or placed on a tabletop with the provided rubber feet.

For ZipClip mounting instructions, see the UCS FT 901 and UCS FR 902 User Guide at www.extron.com.

Connecting Cables

WARNING: Fiber optic connectors emit continuous invisible light, which may be harmful to the eyes; use with caution. Do

not look into the fiber optic cable connectors or into the fiber optic cables themselves. Plug the attached dust caps into the

optical transceivers when the fiber cable is unplugged.

ADVERTISSEMENT : Les connecteurs de fibre optique émettent une lumière invisible continue, qui peut être dangereuse

pour les yeux ; à utiliser avec précaution. Ne pas fixer directement les connecteurs optiques ou les câbles fibre optique.

Branchez les protections contre la poussière dans l’ensemble émetteur/récepteur lorsque le câble fibre optique est

débranché.

The illustration below shows connections for the UCS FT 901 and UCS FR 902.

POWER

12V

HOST

USB-C

SS 5G Tx

OUTPUT

POWER

12V

1.0A MAX

INPUT

OUTPUTS

WER

A MAX

INPUT

UTPUT

POWER

12V

DEVICES INPUT

1.5 A

1.6A MAX

Ground

+12 VDC input

External Power Supply

(12 VDC, 2.0 A max.)

Ground all

Devices

Ground

+12 VDC input

External Power Supply

(12 VDC, 0.5 A max.)

Ground all

Devices

0.1A MAX

USB

USB Camera

Receiver

USB

Laptop

Transmitter

Multimode Fiber Optic Cable

Compatible with USB 3.x, 2.0, 1.x

peripheral devices

Compatible with USB 3.x

host ports ONLY

68-3621-50 Rev. D

08 21

For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the

Extron Safety and Regulatory Compliance Guide on the Extron website.

All trademarks mentioned are the property of their respective owners.

Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876

Connecting Power

1. Power off all devices that will be directly connected to the receiver.

2. Wire the provided 24 W power supply (see previous page, 1)

to the receiver 2-pole captive screw connector (3), and the

provided 6 W power supply (2) to the transmitter (see figure at

right for wiring instructions).

NOTE: The UCS FT 901 (transmitter) can also be powered

by the Host device, without the need for the external

power supply.

3. Once a unit receives power, the front panel Power LED (see unit

illustrations to the right, A) lights.

Connecting the Host (Transmitter)

1. Connect a USB Type A-to-C (or Type C-to-C) cable from the

Host device to the transmitter HOST port (see previous page, 4).

The HOST LED on the transmitter (see figure above right, B)

lights as communication between the transmitter and host device

is established.

NOTE: The transmitter is compatible with and must be

connected to a USB 3.x host port ONLY. Ensure that

the USB cable used between the USB port of the

Host PC and transmitter input supports USB 3.x.

USB 3.x ports are either blue Type A, Type C, or

labeled with a SuperSpeed trident logo (see below).

2. Connect a multimode fiber optic cable from the output port of the transmitter to the input port of the receiver (see previous

page, 5).

3. Mount the devices, if appropriate.

4. Power on the host device.

5. The LINK LED (see figure above right, C) lights as an indication that a link exists from the host PC to the receiver.

a. If the transmitter is powered by a host PC and is not connected to the receiver, only the HOST LED (B) lights, and the

LINK LED (C) remans unlit.

b. If the transmitter and receiver are powered locally and connected via fiber cable, but no PC is connected, the LINK LED

Connecting the Devices (Receiver)

The receiver is compatible and can be connected to USB 3.x, 2.0, & 1.x peripheral devices. Connect up to two USB peripheral

devices to the receiver devices ports (see previous page, 6). The order of connection does not matter.

The UCS FR 902 (receiver) supplies up to 5 V, 1.5 A to each connected peripheral device.

The system is now ready to operate.

Captive Screw Connector

Tie Wrap

Heat

Shrink 1/8"

(3 mm)

7/8"

(22 mm)

3/16"

(5 mm) Max.

UCS FR 902

LINK

STATUS

POWER

12V

--A MAX

DEVICES INPUT

1.5 A

A C

UCS FT 901e

LINK

HOST

STATUS

POWER

12V

0.1A MAX

HOST

USB-C

SS 5G Tx

OUTPUT

A B C

A B

This manual suits for next models

Table of contents

Other Extron electronics Transmitter manuals

Extron electronics

Extron electronics DTP2 T 201 D Series User manual

Extron electronics

Extron electronics HFX 100 Tx User manual

Extron electronics

Extron electronics DVI 201xi TX User manual

Extron electronics

Extron electronics DTP T EU 4K 331 User manual

Extron electronics

Extron electronics DTP T HWP 232 D User manual

Extron electronics

Extron electronics TP Series User manual

Extron electronics

Extron electronics DTP T EU 232 User manual

Extron electronics

Extron electronics XTP T UWP 202 4K User manual

Extron electronics

Extron electronics XTP T EU 202 User manual

Extron electronics

Extron electronics DTP3 T 101 D User manual

Extron electronics

Extron electronics MTP T 15HD A User manual

Extron electronics

Extron electronics DTP2 T 202 FB User manual

Extron electronics

Extron electronics FOX II T HD 4K User manual

Extron electronics

Extron electronics TP T 15HD 45 User manual

Extron electronics

Extron electronics DTP2 T 203 User manual

Extron electronics

Extron electronics DTP3 T 203 User manual

Extron electronics

Extron electronics USB Extender Plus Series User manual

Extron electronics

Extron electronics ExSens User manual

Extron electronics

Extron electronics MTP T 15HD A D User manual

Extron electronics

Extron electronics XTP T HDMI User manual

Extron electronics

Extron electronics DTP T USW 333 User manual

Extron electronics

Extron electronics XTP T UWP 202 User manual

Extron electronics

Extron electronics DTP T FB 232 User manual

Extron electronics

Extron electronics XTP T VGA User manual

Popular Transmitter manuals by other brands

NIVELCO

NIVELCO EasyTREK SCA-300 Series Programming manual

Honeywell

Honeywell 5816WMBR installation instructions

Kamstrup

Kamstrup READy MTU Installation and operation guide

Omega

Omega ZW Series user guide

ABB

ABB Field 264H Instructions for installation

Alinco

Alinco DJ-V17T Service manual

Dejero

Dejero EnGo 3x manual

Rosemount

Rosemount 4600 Reference manual

Speaka Professional

Speaka Professional 2342740 operating instructions

trubomat

trubomat GAB 1000 instruction manual

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 instructions

Rondish

Rondish UT-11 quick start guide

MG 10JRE instruction manual

Burkert

Burkert 8177 operating instructions

Firetide

Firetide HotPort 3203 Hardware installation guide

Tele Radio

Tele Radio T9-02 User instructions

Rotronic

Rotronic HygroFlex HF3 Series user guide

Jamara

Jamara FCX6 Pro Tel Instruction