Extron electronics TLP Pro 1225MG User manual
1
IMPORTANT:
Go to for the
complete user guide and installation
instructions before connecting the
product to the power source.
www.extron.com
TLP Pro 1225MG and TLP Pro 1525MG • Setup Guide
Overview
The Extron TLP Pro 1225MG and TLP Pro 1525MG are wall-mounted touchpanels with capacitive, edge-to-edge glass
touchscreens. The TLP Pro 1225MG has a 12.1 inch screen with a 1280x800 resolution. The TLP Pro 1525MG has a 15.6 inch
screen with a 1366x768 resolution. Both touchpanels are ideal for any AV applications requiring large touchpanels with exible
mounting options and fully customizable interfaces. This guide provides instructions for experienced installers to mount and install
these touchpanels. For more complete details, see the TLPPro 1225 and TLPPro 1525 Series User Guide at www.extron.com.
Setup Checklist
Get Ready
Download and install the latest version of the following software:
GUI Designer — for designing layouts for Extron TouchLink®Pro touchpanels and third party touch interfaces
Global Configurator®Professional or Global Configurator Plus — for setting up and conguring the control processor
and touchpanel
Toolbelt — provides device discovery, device information, rmware updates, conguration of network settings, system
utilities, and user management for TouchLink Pro devices
Global Scripter®— provides an integrated development environment for Extron control systems programming.
NOTE: All four software programs are available from www.extron.com.
Obtain the following network information from your network administrator:
DHCP status (on or off). If DHCP is off, you also require:
IP address Subnet mask Gateway
Username — This can be either admin or user.
Passwords — The factory congured passwords for all accounts on this device have been set to the device serial number.
Passwords can be changed during conguration. Passwords are case sensitive.
NOTE: If the device is reset to default settings, the passwords are reset to the default password, which is extron (for
either admin or user).
Make a note of the touchpanel MAC address.
Mount and Cable All Devices
ATTENTION:
• Do not power on the touchpanels until you have read the Attention in the “Power Supply” section of the TLPPro 1225
and TLP Pro 1525 Series User Guide.
• Ne branchez pas les écrans tactiles avant d’avoir lu la mise en garde dans la section «sources d’alimentation» du
TLPPro 1225 and TLP Pro 1525 Series User Guide.
Mount the units. There are several mounting options for TouchLink Pro touchpanels (see Mounting on page 2).
Connect the touchpanel to a Power over Ethernet (PoE) injector (not provided). Extron recommends the PI 140 power injector,
which must be purchased separately (see Rear Panel Features on page 4).
Connect the power injector to the LAN and power it on.
An Extron IP Link®Pro control processor must be connected to the same Ethernet subnetwork as the touchpanel.
Set up the Touchpanels for Network Communication
Connect the PC that you will use for setup, the control processor, and touchpanel to the same Ethernet subnetwork.
Use the Setup Menu (see page 5) or Toolbelt (see Toolbelt Help File) to set the DHCP status and, if necessary, the IP
address, subnet mask, gateway, and related settings for the touchpanel.
Configure the Touchpanels
Create a graphical user interface with GUI Designer (see GUI Designer Help File for step-by-step instructions).
Associate functions with the graphical user interface features by conguring (see the Global Configurator Help File) or
programming (see the Global Scripter Help File) the system. Global Scripter provides an Extron-exclusive Python library
(ControlScript®) and Global Scripter modules to get you started.
2
TLP Pro 1225MG and TLP Pro 1525MG • Setup Guide
Mounting
ATTENTION:
• Do not install the TLP Pro 1225MG, or TLP Pro 1525MG in a re resistant rated wall or partition assembly.
• Ne pas installer le TLP Pro 1225MG ou le TLP Pro 1525MG dans un mur résistant au feu ou une cloison.
• All structural steps and electrical installation must be performed by qualied personnel in accordance with local and
national building codes and electrical codes.
• Toute étape structurelle et installation électrique, doit être effectuée par un personnel qualié, conformément aux codes
du bâtiment, aux codes incendie et sécurité, et aux codes électriques, locaux et nationaux.
Wall Mounting
The touchpanels can be wall mounted, using the provided hardware. Where local codes require a rear metal enclosure, either model
can be mounted using the Extron BB 700M (not provided). Figure 1 shows the TLP Pro 1525MG. Mount the TLP Pro 1225MG in the
same way.
With a wall box
Some local building codes require the touchpanel to be mounted in a wall box such as the Extron BB 700M. This installation
procedure is described below.
1. Cut a hole in the drywall, 9.55 inches (24.26 cm) wide x 6.55 inches (16.64 cm) high, and install the BB 700M ( see gure 1, 1),
as described in the BB 700M Installation Guide (see www.extron.com).
2. Place the metal mounting plate against the wall, mark the
four mounting holes, and drill four pilot holes (2).
Install BB 700M (optional).
TLP Pro 1525MG
Back View
Hold the touchpanel at a slight angle.
Mount the touchpanel over the two
hooks on the mounting plate.
Add the mounting plate. Align with
the wall box and mark holes for screws.
Secure the mounting plate
to the wall with screws (4).
Place the provided mounting screws (2)
with washers in the mounting screw slot
in the touchpanel.
6
5
3
1
2
4
7
Secure the touchpanel by tightening the
mounting screws against the base of the
mounting plate.
3. Secure the mounting plate with four #10
screws (3).
4. Run and connect cables to the back of the
touchpanel (4, and see Rear Panel
Features on page 4).
5. Insert the two provided Phillips pan
head #6-32 x ¾ inch length screws
with washers in the mounting screw
slot (5, see Figure 1, Back View
inset). Leave a gap for the ange at the
bottom of the mounting plate to t into.
6. Hold the touchpanel at a slight angle
and lower the notches at the top of the
back panel (6) over the hooks of the
mounting plate.
7. Swing the bottom of the touchpanel
inwards so that it lies at against
the mounting plate with the ange
at the bottom of the mounting plate
sitting in a groove in the bottom of the
touchpanel.
8. Secure the touchpanel to the mounting
plate with the mounting screws (7).
Without a wall box
If the wall box is not required by local building
codes, you can mount the touchpanel directly into
drywall.
1. Download the cut-out template for your touchpanel
from www.extron.com. Print it at 100% (no scaling).
2. Use the template to mark the wall, cut the hole, and drill
the four pilot holes.
The size of the cut-out hole is 9.25 inches (23.50 cm) wide x
6.25 inches (15.88 cm) high.
3. Secure the mounting plate and complete the installation, as
described in steps 3 through 8 above.
steps 3 through 8
Figure 1. TLP Pro 1525MG Mounting
3
Product Category
Rack Mounting
These touchpanels can be mounted in any standard 19-inch equipment rack, using the optional rack mounting kit. The
TLP Pro 1225MG can be mounted with the RM2 mounting kit. The TLP Pro 1525MG can be mounted with the RM3 mounting kit.
Read the “Underwriters Labs Guidelines for Rack Mounting” in the TLPPro 1225 and TLP Pro 1525 Series User Guide and follow the
instructions provided with the appropriate kit.
Front Panel Features
Figure 2 shows the TLP Pro 1225MG front panel diagram. The TLP Pro 1525MG features are very similar.
AB
C
DD
EF
Figure 2. TLP Pro 1225MG Front Panel
AAmbient light sensor — Monitors ambient light level and adjusts screen brightness.
BStatus light — Can be programmed to provide system feedback. The LED light bar is located above the screen.
CCapacitive touch screen — Provides simple control of AV systems:
zThe TLP Pro 1225MG has a 12.1 inch screen with a 1280x800 resolution.
zThe TLP Pro 1525MG has a 15.6 inch screen with a 1366x768 resolution.
DSpeakers — Provide stereo audio for video preview and audible feedback from button presses. They are located below the
screen, one on each side of the panel.
EMotion sensor — Detects motion between three to ve feet from the touchpanel, and at least 15° from the center axis.
zIf the Sleep Timer has been set, and no motion has been detected for a user-dened period of time, the touchpanel
enters sleep mode.
zIf Wake on Motion has been set, and motion is detected by the sensor while the screen is in sleep mode, the screen
display is restored and active.
For more information about setting the Sleep Timer or Wake on Motion, see the “Setup Menu” section of the TLPPro 1225
and TLP Pro 1525 Series User Guide.
FMenu button — Activates the setup menu (see Setup Menu). It is accessed from under the touchpanel. It performs the same
function as the rear panel Menu button but is easier to reach when the touchpanel is installed.
gure 2
4
TLP Pro 1225MG and TLP Pro 1525MG • Setup Guide
Rear Panel Features
RESET
MENU
1
HDMI IN
XTP /
LAN /
PoE
2
A
B
C
A
D
E
F
G
H
I
Figure 3. TLP Pro 1225MG Rear Panel
AMounting plate notch (2) — Fit over the hooks at the top of the mounting plate (see Wall Mounting on page 2).
BReset LED — Provides feedback about the reset status when the user presses the reset button.
CReset button — Pressing the Reset button allows the unit to be reset in any of three different modes (see Reset Modes: a
Brief Summary on page 5). For more information, see the TLPPro 1225 and TLP Pro 1525 Series User Guide.
DMenu button — Activates the setup menu (see Setup Menu).
EUSB connectors (2) — For peripheral controls.
FMounting screw slot (2) — Insert the provided screws here. Secure the touchpanel to the mounting plate.
GAudio output — For use with headphones or assistive listening devices.
HHDMI input — For alternative video input.
IXTP/LAN/PoE input
zXTP input — Connect the touchpanel to the XTP source using a twisted pair cable, terminated with an RJ-45 connector.
For complete information about which cables to use, see the user guide for your XTP product.
zLAN input — Connect the touchpanel to the LAN using a twisted pair cable, terminated with an RJ-45 connector.
zPoE input — the connector can be used with a PoE power injector (see Connecting Power on the next page).
NOTE: Some XTP models are able to remotely power these touchpanels but not all have that capability. Go to the Extron
website and check the product page for your XTP model to ensure it can power your touchpanel.
An Extron IP Link Pro control processor must also be connected to the same network as the TouchLink Pro touchpanel.
gure 3
note
5
Product Category
1. Connect a straight-through Ethernet cable from the power injector to a switch or
router (see gure 4, 1). This cable carries network information from the switch
or router to the power supply input.
2. Connect a second straight-through cable (2) from the power injector to the
TLP Pro touchpanel XTP/LAN/PoE connector (see figure 3, I, on page 4).
This cable carries the network information and 48VDC from the power injector
to the touchpanel.
3. Connect the IEC power cord to a convenient 100 VAC to 240 VAC, 50-60 Hz
power source (3).
Alternatively, use an Ethernet cable to connect the XTP/LAN/PoE port of the interface
to a PoE+ switch or connect the touchpanel directly to an XTP model that is capable
of remotely powering a touchpanel (see the note on page 4).
Setup Menu
Press the Menu button (figure 2, Fon page 3 or figure 3,
D, on page 4) to open the setup menu. Select any of the
six available screens (Status, Network, Display, Audio,
Input and Advanced) by pressing the appropriate button in the
navigation bar at the top of the screen (for more information, see the
TLPPro 1225 and TLP Pro 1525 Series User Guide).
Figure 5 shows the setup menu for the TLP Pro 1225MG. The setup
menu for the TLP Pro 1525MG is almost identical.
Info
Model: TLP Pro 1225MG
Part Number:60-1787-02
Firmware
Version: 1.02.0000.b003
PoE: Active
Network
IP Address:
DHCP:
Host Name:
Off
192.168.254.251
TLP-AB-CD-EF
Display
Resolution:
Project:
Sleep Timer:
1280x800
1280x800
5 Minutes
Audio
Master Volume:
Master Mute: Off
100
Input
HDMI:No Signal
Status DisplayAudio Advanced Exit
NetworkInput
Advanced
Controller IP: 192.168.254.250
Project Size: 1/197 MB
Bootloader
Version: 1.03.0000
XTP: 1280x720 HDCP
Figure 5.Setup Menu: Status page for TLP Pro 1225MG
100-240V~50/60 Hz
1.1A MAX INPUT OUTPUT
POWERED TLP
LAN
To Network or
XTP Device
To a TLP Pro
touchpanel
Extron PI 140
12
3
Figure 4. Connecting the Power Injector
Reset Modes: a Brief Summary
The TLP Pro 1225MG and TLP Pro 1525 MG offer the following reset modes. For full information about the modes, see the
TLPPro 1225 and TLP Pro 1525 Series User Guide.
• Use factory firmware: Use this mode to replace rmware in the event of rmware failure. Press and hold the Reset
button (see figure 3, C) while applying power to the unit.
• Reset All IP Settings: Use this mode to reset all network settings without affecting user-loaded les. Press and
hold the Reset button for 6 seconds. After the Reset LED (B) ashes twice, release and
momentarily press the Reset button.
• Reset to Factory Defaults: Use this mode to return the interface to factory default settings. Press and hold the Reset
button for 9 seconds. After the Reset LED ashes three times, release and momentarily press
the Reset button.
NOTES:
• The factory congured passwords for all accounts on this device have been set to the
device serial number. Passwords can be changed during conguration. Passwords are
case sensitive.
• If the device is reset to default settings, the passwords are reset to the default
password, which is extron (for either admin or user).
• Enable or Disable the
DHCP Client
Use this mode to toggle between DHCP enabled and DHCP disabled.
Press the Reset button ve times, consecutively. After the fth press, do not press the button
again within 3 seconds. If DHCP was enabled, it is now disabled and the Reset LED blinks
three times. If DHCP was disabled, it is now enabled and the Reset LED blinks six times.
Connecting Power
ATTENTION:
• Do not power on the touchpanels until you have read the ATTENTION in the “Rear Panel Features” section of the
TLPPro 1225 and TLP Pro 1525 Series User Guide.
• Ne branchez pas les écrans tactiles avant d’avoir lu la mise en garde dans la section «Rear Panel Features » du
TLPPro 1225 and TLP Pro 1525 Series User Guide.
The power injector must be purchased separately. Figure 4 shows the Extron PI 140. Your power injector may look different.
6
For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the
Extron Safety and Regulatory Compliance Guide on the Extron website.
For information about replacing and disposing of batteries, see the TLP Pro 1225 and TLP Pro 1525 Series User Guide at
www.extron.com.
© 2020 Extron Electronics — All rights reserved. www.extron.com
All trademarks mentioned are the property of their respective owners.
Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876
TLP Pro 1225MG and TLP Pro 1525MG • Setup Guide
68-3474-50 Rev. A
07 20
Other manuals for TLP Pro 1225MG
1
This manual suits for next models
1
Table of contents
Other Extron electronics Touch Panel manuals
Extron electronics
Extron electronics TLP 700TV User manual
Extron electronics
Extron electronics ZRTP Series User manual
Extron electronics
Extron electronics TLP 1000MV User manual
Extron electronics
Extron electronics TLP 700TV User manual
Extron electronics
Extron electronics TLP Pro 1220TG User manual
Extron electronics
Extron electronics TLP Pro 300M Series User manual
Extron electronics
Extron electronics TLP 1000MV User manual
Extron electronics
Extron electronics RWM 1 User manual
Extron electronics
Extron electronics TLP Pro 525M seriesl User manual
Extron electronics
Extron electronics TLP Pro 720M User manual
Extron electronics
Extron electronics TLP Pro 1520TG User manual
Extron electronics
Extron electronics TLP Pro 1230WTG User manual
Extron electronics
Extron electronics TouchLink Series Instructions for use
Extron electronics
Extron electronics TouchLink TLP 350CV User manual
Extron electronics
Extron electronics TLP Pro 1230WTG User manual
Extron electronics
Extron electronics TouchLink TLP Pro 520M User manual
Extron electronics
Extron electronics TouchLink TLP 710CV User manual
Extron electronics
Extron electronics Scan Rate Indicator SRI 200 User manual
Extron electronics
Extron electronics TouchLink TLP Pro 725C Series User manual
Extron electronics
Extron electronics TLP Pro 1225MG User manual
Popular Touch Panel manuals by other brands
IBASE Technology
IBASE Technology ASTUT-152-RE1S user manual
YASKAWA
YASKAWA TP 610C manual
B&R
B&R Power Panel C Series user manual
Beijer Electronics
Beijer Electronics X2 control Hardware and installation manual
AXIOMTEK
AXIOMTEK GOT321W-521 user manual
TRIDONIC.ATCO
TRIDONIC.ATCO x-touchBOX Operation manual
