Extron electronics KNX 100G User manual

KNX 100G • Setup Guide

This setup guide covers the physical installation of the KNX 100G and KNXnet/IP tunneling from a PC to a KNX network during

conguration and commissioning.

The KNX 100G allows better integration of control with KNX building management systems (BMS). The product serves as a

gateway for control systems and ETS software to the KNX bus, and it is designed to be installed onto a DIN rail with a width of 1

unit (18 mm).

Power is supplied via the KNX bus; an external power supply is not necessary. The KNX bus can be accessed from any point on

the LAN. The IP address can be obtained by a DHCP server or by manual conguration. There are ve simultaneous connections

possible for access via KNXnet.

Figure 2. KNX 100G DIN Rail Installation

Installing Onto DIN Rail

1. Ensure the DIN rail is securely mounted onto the wall or furniture.

2. Place top rear against wall/furniture (Figure 2, 1).

3. Slide the unit down onto top of rail (Figure 2, 2).

4. Tilt the unit and snap onto the rail (Figure 2, 3).

Figure 1. KNX 100G Controls and Displays

DIN Rail

KNX 100G

Patent(s): www.extron.com/patents

33-2700-01 A

Prog. KNX

__.__.____

Prog

__.__.___

KNX 100G

KNX

Mode

P/Esc

Conn

33-2558-01 B

est

KNX 100G

Place top rear against

wall/furniture.

Slide down the unit

onto top of rail.

Tilt the unit an

snap into rail.

KNX 100G

Patent(s): www.extron.com/patents

33-2700-01 A

KNX 100G

Patent(s): www.extron.com/patents

33-2700-01 A

KNX 100G

Patent(s): www.extron.com/patents

33-2700-01 A

Prog. KNX

__.__.____

Prog

__.__.___

KNX 100G

KNX

Mode

P/Esc

Conn

33-2558-01 B

est

LAN

33-2558-01 B

www.extron.com/patents

Bottom View

AKNX Bus connector

BProgramming Mode Button

CProgramming Mode LED (Red)

DKNX LED (multicolor)

EMode LED (multicolor)

FIP LED (multicolor)

GButton Connection Up

HButton Connection Down

IEthernet/LAN Connector

Figure 3. KNX 100G Application Diagram

LED Status Indicators

C Programming Mode LED

LED STATUS Meaning

LED lights red Programming mode is active

LED Off Programming mode is not active

EMode LED

LED STATUS Meaning

LED lights green Device is working in standard operation mode

LED lights red Programming mode is active

LED ashes green 1x...5x Programming mode is not active

Manual operation is active

The selected tunnel (1-5) is not used and free

LED ashes orange 1x...5x Programming mode is not active

Manual operation is active

The selected tunnel (1-5) is used and free

LED ashes red Programming mode is not active

Manual operation is not active

The device is not properly loaded for example after an interrupted download

F IP LED

LED STATUS Meaning

LED lights green The device has an active Ethernet link and valid IP settings.

LED lights red The device has an active Ethernet link and invalid IP settings or not yet received the IP settings by a

DHCP server.

LED ashes green IP telegram trafc

DKNX LED

LED STATUS Meaning

LED lights green KNX 100G successfully powered

LED ashes green Telegram trafc on the KNX bus

LED lights red shortly Communication failure on the KNX bus

KNX 100G

Patent(s): www.extron.com/patents

33-2700-01A

est

KNX 100G

Patent(s): www.extron.com/patents

33-2700-01 A

Prog. KNX

__.__.____

KNX 100G

KNX

Mode

P/Esc

Conn

Ethernet

Twisted Pair

Cable

IPCP PRO 550

OVER

LIMIT

RIR

12 3 4 5 6 7 8

RTS

CTS

COM

IR/SERIAL

RELAYS FLEX

I/O

SLIMIT

OVER

eBUS

SWITCHED

12VDC

1000

LINK

ACT

5 6

Light

Shutters

Dimmer

Volume

Thermostat

(Temperature)

Dimme

Volum

KNX 100G

IPCP Pro 550

IPCP

Pro 550

TLP Pro 725M

Network

IPCP PRO 550

OVER

LIMIT

RIR

1234 5 6 78

RTS

CTS

COM

IR/SERIAL

RELAYS FLEX

I/O

SLIMIT

OVER

eBUS

SWITCHED

12VDC

1000

LINK

ACT

5 6

TLP Pro 725M

KNX

Bus

KNX 100G Network Installation

1. Using a certied KNX twisted pair cable, connect to the

KNX BUS located on the top of the device (see gure 3).

2. Connect an ethernet cable between the Ethernet port

located at the bottom of the KNX 100G and the local

network.

3. Congure the KNX 100G using ETS.

4. Congure your Extron Control System using the Extron

driver targeted at your congured KNX 100G.

NOTE: Engineering Tool Software (ETS) is an application

for designing, commissioning, and debugging KNX

installations. Click this link to view and purchase ETS

for your KNX setup. KNX system setup should be done

by a certied KNX professional.

KNX 100G Setup

1. Add KNX 100G Interface Within ETS

Within ETS, the KNX 100G interfaces can be selected and setup via “Bus Interfaces”.

NOTE: ETS can access congured KNX 100G interfaces without a database entry if the default settings are compatible with

the KNX installation. If the KNX 100G setup does not comply with installation conditions, it must be configured within an

ETS project. See Configure Interface Properties on page 4.

After connecting the KNX 100G to the LAN and the KNX bus, the device should automatically appear in ETS within the “Bus”

menu under “Discovered Interfaces”. By double clicking on the discovered interface, it will be selected as the current interface. On

the right side of the ETS window, all specic information and options of the connection appear (see gure 5).

2. Setup Individual Address for Tunneling

The device’s name and “Individual Address” can be changed within your ETS project. The KNX 100G has an individual address

which can be used to access the device.

The device supports up to ve connections for control. Each connection is associated with one of the ve individual addresses

in the device. The addresses can be assigned via ETS. Telegrams sent to the bus contain a sender address from one of the ve

additional addresses, and response telegrams can be transmitted to respective clients.

Additional individual addresses must be selected from the address range of the bus line in which the interface is installed and may

not be used by another device. The individual KNX 100G address and the addresses for additional tunneling connections can be

changed within the ETS project after the device has been added to the project.

Factory Default Settings

Setting Value

Individual Device Address 15.15.255

Number of congured KNXnet/IP tunneling

connection

Individual address of tunneling connection 15.15.250

IP address assignment: DHCP

Reset to Factory Device Settings

The following callouts reference Figure 1 on page 1.

1. Separate the KNX Bus connector Afrom the device.

2. Press and hold the Programming Mode button B.

3. Reconnect KNX Bus connector A of device.

4. Continue holding the Programming Mode button Bfor six seconds.

5. A short ashing of all LEDs (CDEF)visaulizes the successful reset of the device to factory default settings.

Figure 5. Changing Device Address in ETS

Figure 4. New Connection in Bus Interfaces

For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the

Extron Safety and Regulatory Compliance Guide on the Extron website.

All trademarks mentioned are the property of their respective owners.

Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92905, 800.633.9876

68-3345-50 Rev. B

02 19

3. Conﬁgure Interface Properties

After adding the KNX 100G to a project, you can change the Individual Address and IP setting in Properties (see gure 7

below). In ETS 4, additional individual addresses will appear in the Topology view.

Within the ‘Settings’ overview, each individual KNX address and the device’s name can be changed. ‘Properties’ will appear on

the right side of the ETS window after clicking on the KNX 100G device entry within the project’s topology view. Click on the list

entry and type in the desired address into the Individual Address texteld to change an individual address (see 1in Figure

6). If the texteld frame switches to color red after entering the address, the address is already taken within your ETS project.

NOTE: Make sure none of the individual KNX addresses are in use within the KNX installation.

If the physical KNX addresses of the tunneling connections have been assigned via ETS, a manual address setting on

the device is not allowed.

The IP network specic options of the KNX 100G can be changed. In the ‘Properties’ window, click on the ‘IP’ tab. Change

Obtain an IP address automatically to Use a static IP address to set the IP address, subnet mask, and

default gateway freely 2.

Figure 6. ETS Properties Settings Figure 7. ETS Properties IP

4. Program the KNX System

Via the KNX Bus

The device only needs to be connected to the KNX bus. ETS requires an additional interface to have access to the bus.

Both the individual address and the entire application can be programmed via the KNX bus. Programming via the bus is

recommended if no IP connection can be established.

Via KNXnet/IP Tunneling

No additional interface is required. Programming via KNXnet/IP Tunneling is possible if the device already has a valid IP

conguration. The device is displayed in the interface conguration of ETS and must be selected. The download is executed

via ETS.

KNX 100G

0.0.0 2

Table of contents

Other Extron electronics Recording Equipment manuals

Extron electronics

Extron electronics Computer-Video Interface RGB 508 AKM User manual

Extron electronics

Extron electronics RGB 460xi SC Series User manual

Extron electronics

Extron electronics IP LINK IPL T SFI244 User manual

Extron electronics

Extron electronics RGB 472xi User manual

Extron electronics

Extron electronics P/2 DA1 USB User manual

Extron electronics

Extron electronics RGB 460xi FSR Series User manual

Extron electronics

Extron electronics HAI 100 4K Manual

Extron electronics

Extron electronics PIP 422 User manual

Extron electronics

Extron electronics IPL T S1 User manual

Extron electronics

Extron electronics VNM Enterprise User manual

Extron electronics

Extron electronics RGB 203 Rxi VTG User manual

Extron electronics

Extron electronics RGB 302 User manual

Extron electronics

Extron electronics 12G HD-SDI 101 User manual

Extron electronics

Extron electronics RGB 440 User manual

Extron electronics

Extron electronics RGB 109xi User manual

Extron electronics

Extron electronics SSP 7.1 User manual

Extron electronics

Extron electronics SSP 7.1 User manual

Extron electronics

Extron electronics IP Link IPL T CR48 User manual

Extron electronics

Extron electronics VNR 100 User manual

Extron electronics

Extron electronics RGB 302 User manual

Extron electronics

Extron electronics RGB 304 User manual

Extron electronics

Extron electronics RGB 192 User manual

Extron electronics

Extron electronics RGB 103 User manual

Extron electronics

Extron electronics NetPA AT Series User manual

Popular Recording Equipment manuals by other brands

KV2 Audio

KV2 Audio 500 Series user guide

Robotics Technologies

Robotics Technologies microBus-Cam II installation manual

Seca

Seca 460 quick start guide

Cognex

Cognex MVS-8000 Series Hardware manual

Mect

Mect MPNC006 Series user manual

Bad Caf

Bad Caf THE LEASH operating manual

Strymon

Strymon NIGHTSKY user manual

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U user manual

Tews Technologies

Tews Technologies TPMC465 user manual

Honeywell

Honeywell Excel 50 user guide

SeaLevel

SeaLevel COMM+8.LPCI user manual

Arturia

Arturia AUDIOFUSE STUDIO user manual

Rukra

Rukra RK-1240 quick start guide

Samson

Samson SCOM owner's manual

Dynacord

Dynacord DPS260 owner's manual

Nice

Nice Core user manual

Pyle Pro

Pyle Pro PSS8 manual

RF-System

RF-System TinyGate Assembly and user's manual