Extron electronics UTS 100 Series User manual

UTS 100 (70-1028-01)

(8) #4-40 x 3/16 inch product mounting screw

(4) #8 x 1/2 inch shelf mounting screw

UTS 150 (70-1028-02)

(8) #4-40 x 3/16 inch product mounting screw

(2) #8-32 Thumbnut

Step 1 — Mount Devices on the Shelf

ATTENTION: Some products have hexagonal holes

in their base, which anchor stand-offs for internal circuit

boards (see the gure to the right). Using these holes will

damage the product and will not provide secure mounting.

Before securing a device to the shelf, decide where the device

will be placed. Ensure that adequate space remains for running

cables.

1. Place the device on the shelf so that the rack mounting

holes are aligned with two diagonally opposite product

mounting holes in the shelf (see gure at right).

Remove any rubber feet attached to the device.

2. Secure the device to the shelf, using two

of the provided #4-40 x 3/16 inch

screws.

3. Use the rectangular (wire tie)

openings for tie wraps if

necessary.

UTS 100 Series • Setup Guide

The Extron UTS100 and UTS 150 under-table shelf system accommodates half-rack,

quarter-rack, and eighth-rack products in a half-rack width installation. The shelves can

accommodate a single device or combinations of smaller devices.

Included Parts

Step 2 — Install the UTS 100 (Primary Shelf) Under the Table

The UTS 100 may be mounted under furniture in

one of two ways: using the keyhole slots for

a removable installation or the clearance

holes for a fixed installation.

1. Hold the UTS 100 under

the desk or table and mark

the locations of four corner

mounting holes. Clearance

hole

Keyhole

slot

#4-40 Thread for

Rack Mounting

Hexagonal

Stand-off (for

mounting circuit

board)

Use 2 mounting holes on diagonally

opposite corners of device.

(2) #4-40 x 3/16"

screws

UTS 100

Wire tie

openings

Product

mounting

holes

Get other manuals https://www.bkmanuals.com

Step 3 — Install the UTS 150 (Secondary Shelf)

1. Insert the hooks of the UTS 150

into the front posts and rear studs

of the top adjacent shelf, then

push the UTS 150 upward to lock

it in place (see image at right).

2. Secure the #8-32 thumb nuts to

the rear studs of the top adjacent

shelf.

3. Repeat steps above to add more UTS 150

shelves to the expandable shelf system.

Servicing options

The UTS 150 may be adjusted to three different positions for servicing cables and mounted

devices.

ATTENTION: Before pivoting the UTS 150, disconnect all cables from any device(s) on

the UTS system. Not doing so may bend and damage the cables or device(s).

Position 1: To lower the

UTS 150, pull it slightly forward

and release it onto the posts and

studs of the top adjacent shelf

(see image below).

Position 2: To pivot the

UTS 150 from the front,

engage the front hooks to the

front posts of the top adjacent

shelf (see image below).

Position 3: To pivot the

UTS 150 from the back,

engage the rear hooks to the

rear studs of the top adjacent

shelf (see image below).

68-2357-50

Rev. A

02 13

2. Drill four pilot holes, each 3/32 inch (2.38 mm) in diameter, at the marked locations.

ATTENTION: Be careful not to drill

through the table. If the table is too thin or of

a different material for the supplied screws,

use an appropriate type and length.

3. Secure the shelf, using the four provided

#8 x 1/2 inch mounting screws (see image at right).

Rear

studs

UTS 100

UTS 150

Front

posts

#8-32

thumb nut

Get other manuals https://www.bkmanuals.com

This manual suits for next models

Table of contents

Other Extron electronics Rack & Stand manuals

Extron electronics

Extron electronics VM 700T User manual

Extron electronics

Extron electronics PMK 155 User manual

Extron electronics

Extron electronics MMK 1 User manual

Extron electronics

Extron electronics WMK 160 User manual

Extron electronics

Extron electronics UTR 104 User manual

Extron electronics

Extron electronics SMK V SB 33 User manual

Extron electronics

Extron electronics UPB 125 User manual

Extron electronics

Extron electronics MediaLink MLM-UDSM User manual

Extron electronics

Extron electronics Wall Mount Assembly Kit V-LockTM User manual

Extron electronics

Extron electronics MLM 84 Flex55 User manual

Extron electronics

Extron electronics USFM 100 User manual

Extron electronics

Extron electronics SMK 1 User manual

Extron electronics

Extron electronics PMK 150 User manual

Extron electronics

Extron electronics SMK V SB 33 Plus User manual

Extron electronics

Extron electronics MBU 149 User manual

Extron electronics

Extron electronics PoleVault Systems PVS 300 User manual

Extron electronics

Extron electronics SMK 2 User manual

Extron electronics

Extron electronics RM 700M User manual

Extron electronics

Extron electronics FOX3 Matrix Series User manual

Extron electronics

Extron electronics PMK 560 User manual

Extron electronics

Extron electronics FCMP 44 User manual

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 