Extron electronics DTP T HWP 232D User manual

IMPORTANT:

Go to www.extron.com for the complete

user guide, installation instructions, and

specifications before connecting the

product to the power source.

DTP T HWP/UWP 232/332 D • Setup Guide

This setup guide provides instructions for an experienced installer to set up and operate the Extron DTP T HWP D and

DTP T UWP D family of Twisted Pair (TP) wallplate extenders.

Installation

Step 1 — Disconnect Power

Disconnect all equipment power sources.

Step 2 — Prepare the Mounting Surface

ATTENTION:

• Installation and service must be performed by

authorized personnel.

• L’installation et l’entretien doivent être effectués par le

personnel autorisé uniquement.

• The unit must be installed in accordance with the

National Electrical Code and with local electrical and

safety codes.

• L’unité doit être installée conformément au National

Electric Code et aux normes électriques et de sécurité

locales.

NOTE: Use a wall box with a depth of at least 3.0 inches (7.6 cm). Alternatively, the included mud ring (MR 200) can be

used. For more information, see the full product user guide at www.extron.com.

a. Place the wall box against the installation surface and mark the opening guidelines.

TIP: Use a level to mark the opening.

b. Cut out the material from the marked area.

c. Secure the wall box to the wall stud with 10-penny nails or #8 or #10 screws, leaving the front edge ush with the

surface.

d. Run all required cables (see steps 3, 4, and 5) and secure them with cable clamps.

TIP: In order to t the unit in the junction box, do not install boots on TP cables and RJ-45 connectors.

Extron

DTP T UWP 232 D

Signal Output

Cable

Clamp

Decora Faceplate

Screws or

Nails

all opening is

ﬂush with edge of box.

Wall Stud

AUTO SW

CONFIG

IR OUT

HDMI IN

AUDIO IN

HDCP

AUDIO IN

VGA IN

TLP 1000T

IPCP 505

IN1608

DTP HDMI 230 Rx

Projector

100-240V~ -- A MAX

CONFIGURABLE

HDMI HDMI

RS-232 IR

Tx Rx Tx RxG

Tx Rx Tx RxG Tx Rx Tx RxG

HDMI

INPUTS OUTPUTS

Tx Rx

RS-232

LAN

2x25W(8Ω)/2x50W(4Ω)

RESET

AUDIO INPUTS OUTPUTS

REMOTE

LL1R R

L2 R

CLASS2 WIRING

L4R

L5R

+48V

VARIABLE

IN1608SA

MIC/LINE

L6R

SIG LINK

DTPIN

SIG LINK

DTPIN

SIG LINK

DTPOUT

50/60Hz

RS-232 IR

OVERDTP

AMPLIFIED OUTPUT

VOLUME

SCALINGPRESENTATION SWITCHER

IN1608

INPUTS

HDCP

SIGNAL

OUTPUTS

ENTER

Extron

2 3 4 5 6 7 8 A B C

INPUTS

1 2 3 4 5 6 7 8

CONFIG

Extron

DTP T UWP 232 D Tx

Transmitter

Extron

DTP T HWP 232 D Tx

Transmitter

Ethernet

Network

POWER

12V

0.7A MAX

AUDIO

SIG LINK

DTP IN

OUTPUTS

XTP DTP 24 Cable

230'

HDMI

12345678

100

LINK

ACT

COM

IR/S

RTS

CTS

RELAY FLEX

I/O

eBUS

ACTLIMIT

OVER

SWITCHED

12VDC

OVER

LIMIT

IPCP 505

AUTOSW

CONFIG

IROUT

HDMI IN

AUDIO IN

HDCP

AUDIO IN

VGA IN

AUTOSW

CONFIG

IROUT

HDMI IN

AUDIO IN

HDCP

HDMI IN

AUDIO IN

HDCP

DTP T HWP/UWP 232/332 D • Setup Guide (Continued)

Step 3 — Connect Inputs to the Transmitter

Front Panel

A Audio input connector — Connect an unbalanced stereo audio source to this 3.5 mm mini stereo jack.

B HDMI input connector — Connect an HDMI cable between this port and the output port of the digital video source.

C VGA input connector — Connect a VGA cable between this port and the output port of the video source.

D IR output connector — Connect an IR device to this 2-pole, 3.5 mm captive screw

pass-through connector for IR control. Wire the cable as shown in the illustration to the right.

E Mini USB port — Connect a male Mini USB-B cable to this port for SIS conguration and

rmware updates.

Rear Panel

A DC power input connector — Wire and plug the included external

12 VDC power supply into either this 2-pole connector or the power

input connector on the receiver (see the DTP T HWP/UWP 232/332 D

User Guide at www.extron.com for wiring information).

B Over DTP connector — Connect an RS-232 device to this 3-pole,

3.5 mm captive screw connector for pass-through RS-232 control.

C Remote connector — Connect an RS-232 device, contact closure

device, or both to this 5-pole, 3.5 mm captive screw connector to

control switching on the unit. Wire the connector as shown in the

diagram below.

• RS-232 — To control the unit through this port, connect an RS-232

device and congure it as follows: 9600 baud rate, 8 data bits,

1 stop bit, no parity.

• Contact — Momentarily short pins 1 or 2 to ground (G) to select

the corresponding input. Connect pins 1 and 2 to ground (G) to

set the unit to auto switch mode. The device selects the highest

active input (auto switch).

AUTO SW

CONFIG

IR OUT

HDMI IN

AUDIO IN

HDCP

2HDMI IN

AUDIO IN

Extron

DTP T HWP 232 D

AUTO SW

CONFIG

IR OUT

HDMI IN

AUDIO IN

HDCP

AUDIO IN

VGA IN

Extron

DTP T UWP 232 D

DTP OUTREMOTEOVER

DTP SIG LINK

RS-232

CONTACT

Tx Rx

Tx Rx G

POWER

12V

A MAX

0.9

+–

G12

A/S

DTP OUTREMOTEOVER

DTP SIG LINK

RS-232

CONTACT

DTP T UWP 232 D

Tx Rx

Tx Rx G

POWER

12V

A MAX

0.9

+–

G12

A/S

DTP T HWP 232 D and DTP T UWP 232 D

Rear Panel

DTP T UWP 232 D

Rear Panel

Ground

Receive pin on connected unit

Transmit pin on connected unit

Connected RS-232 and

Contact Closure Device Pins

Tx/Rx

Pins

Pin 1 for contact closure contro

Pin 2 for contact closure contro

RxTx

RS-232 Contact

3/16”

(5 mm) Max.

Groun

Signal

A DC power input connector

B Over DTP connector

C Remote connector

D DTP OUT connector (page 3)

E Reset button (page 3)

DTP T HWP/UWP 232/332 D • Setup Guide (Continued)

D DTP OUT connector — Connect one end of a twisted pair cable to this RJ-45 connector and the opposite

end to a compatible receiver.

ATTENTION:

• Do not connect these outputs to a telecommunications or computer data network.

• Ne connectez pas ces appareils à des données informatiques ou à un réseau de

télécommunications.

NOTES:

• The DTP T HWP/UWP 232 D models can transmit video, control, and audio (if applicable)

signals up to 230 feet (70 meters).

• The DTP T HWP/UWP 332 D models can transmit video, control, and audio (if applicable)

signals up to 330 feet (100 meters).

E Reset button — Use an Extron Tweeker or small screwdriver to press and hold the recessed button for 6 seconds while

the switcher is running to perform a factory reset.

Step 4 — Run Cables Between Units

Connect the rear panel transmitter output to a rear panel receiver input using twisted pair cable.

Wire the cable as shown in the diagram to the right.

For optimal performance, Extron highly recommends the following:

zRJ-45 termination with shielded twisted pair cable must comply with TIA/EIA-T568B wiring

standard for all connections.

For more information on TP cable wiring and termination, see the full product user guides at

www.extron.com.

zUse shielded twisted pair cable, 24 AWG solid conductor or better, with a minimum cable

bandwidth of 400 MHz.

ATTENTION:

• Do not use Extron UTP23SF-4 Enhanced Skew-Free AV UTP cable or STP201 cable to link the device with

DTP transmitters or receivers.

• N’utilisez pas le câble AV Skew-FreeUTP version améliorée UTP23SF d’Extron ou le câble STP201 pour relier

le appareil avec les émetteurs ou les récepteurs DTP.

zUse shielded RJ-45 plugs to terminate the cable.

zLimit the use of RJ-45 patches. Overall transmission distance capabilities vary depending on the number of patches

used. If possible, limit the number of patches to two total.

zIf RJ-45 patches must be used in the system, shielded patches are recommended.

Step 5 — Connect the Outputs from a Compatible Receiver

a. Connect a DVI or HDMI cable (depending on your receiver type) between the receiver output port and the input port of

the display.

b. Connect a stereo audio device to the 3.5 mm mini stereo jack to receive the passed-through unbalanced audio.

c. Plug an RS-232 or modulated IR device into the RS-232/IR pass-through port.

Step 6 — Power the Units

The units can be powered one of two ways:

zLocally with the included power supply. A compatible receiver can then be powered remotely through the DTP line.

zRemotely via the DTP line by a locally powered DTP 230 or 330 compatible device.

NOTE: See the DTP T HWP/UWP 232/332 D User Guide at www.extron.com for wiring information.

Wire color

White-green

Green

White-orange

White-blue

Orange

White-brown

Brown

Blue

TIA/EIA

T568-B

TP Wires

12345678

Pins:

SIG LINK

DTP OUT

SIG LINK

DTP IN

68-2547-50 Rev. C

04 15

Step 7 — Final Installation

a. Make all connections, power the units, and test the system for satisfactory operation.

b. At the power outlet, unplug the power supply.

c. Mount the transmitter into the wall box, and attach the supplied Decora® faceplate to the unit.

d. At the power outlet, reconnect the power supply. This powers up both units.

Operation

NOTE: Input switching can be performed only via auto switching, RS-232, or contact closure through the rear panel

connectors.

After all devices are powered up, the system is fully operational.

AUTO SW

CONFIG

IR OUT

HDMI IN

AUDIO IN

HDCP

2HDMI IN

AUDIO IN

Extron

AUTO SW

CONFIG

IR OUT

HDMI IN

AUDIO IN

HDCP

AUDIO IN

VGA IN

Extron

DTP T HWP 232 D

Front Panel

DTP T UWP 232 D

Front Panel

Transmitter LEDs

A Power LEDs — These two-color front panel LEDs on the transmitters light to indicate signal and

power status as follows:

Amber — The unit is receiving power but there is no signal on the HDMI or VGA inputs.

Green — The unit is receiving power and a signal is present on the HDMI or VGA inputs.

B Auto Switch LED — Lights green when auto switch is active (see Rear Panel Con page 2).

C HDCP LEDs — Lights green when HDMI input has been authenticated on the source device.

Audio Conﬁguration

The DTP T HWP D and DTP T UWP D series can embed analog audio inputs onto the digital video output.

NOTE: If no VGA or HDMI signal is present, analog audio will be transported over the DTP connection to the analog audio

output of the receiver.

When an input is selected, audio transport over HDMI can be congured to operate in one of three modes. Each input can be

congured individually for any of the three modes.

zTransport embedded digital audio (default) — The embedded digital audio content on the digital video input is transported.

Analog audio is still separate from the digital embedded audio on the HDMI signal and transported simultaneously over the

DTP output, not embedded onto the digital output.

zEmbed analog audio input — The analog audio input is always embedded to the digital output, replacing whatever content

is already present on the embedded digital audio. Analog audio is also transported over the DTP output as a simultaneous

output.

zAuto select between analog audio and digital audio — When both analog audio and digital embedded audio on HDMI are

present, embedded digital audio on the HDMI signal takes priority. Analog audio is transported simultaneously with the digital

embedded audio content that is already present on the DTP output.

This manual suits for next models

Table of contents

Other Extron electronics Extender manuals

Extron electronics

Extron electronics AKM MAAP User manual

Extron electronics

Extron electronics DTP HDMI 330 User manual

Extron electronics

Extron electronics XTP R HWP 201 User manual

Extron electronics

Extron electronics DTP T USW 223 User manual

Extron electronics

Extron electronics DTP T UWP 4K 232 D User manual

Extron electronics

Extron electronics VGAUXGA Line Drivers With Audio Extender... User manual

Extron electronics

Extron electronics USB Extender Plus T User manual

Extron electronics

Extron electronics 60-871-12 User manual

Extron electronics

Extron electronics HFX 100 Tx User manual

Extron electronics

Extron electronics PowerCage FOX Tx DVI Plus User manual

Extron electronics

Extron electronics DDX 102 Tx User manual

Extron electronics

Extron electronics DTP T DWP 4K 232 D User manual

Extron electronics

Extron electronics HDMI 201 User manual

Extron electronics

Extron electronics PowerCage FOX Tx HDMI User manual

Extron electronics

Extron electronics DTP HDMI 230 User manual

Extron electronics

Extron electronics FOXBOX Tx HDMI User manual

Extron electronics

Extron electronics DTP HDMI 4K D Series User manual

Extron electronics

Extron electronics DTP DVI 4K 230 D Series User manual

Extron electronics

Extron electronics DTP HDMI 301 User manual

Extron electronics

Extron electronics DTP HDMI 301 User manual

Extron electronics

Extron electronics FOX T UWP 302 User manual

Extron electronics

Extron electronics DTP DVI 4K 330 User manual

Extron electronics

Extron electronics FOX II T DP User manual

Extron electronics

Extron electronics DVI 104 User manual

Popular Extender manuals by other brands

SY HDBT-60T installation guide

Appsys ProAudio

Appsys ProAudio ADX-16 user manual

Atlona

Atlona RS232 user manual

IDK

IDK OPF-TH1000-A user guide

Enable-IT

Enable-IT 824WP quick start guide

Worx

Worx Landroid RadioLink WA0864 Get started

TP-Link

TP-Link TL-WA730RE user guide

Camplex

Camplex CMX-HDMI-SFPL user manual

SC&T

SC&T HE03-4K user manual

Marmitek

Marmitek MegaView70 user manual

Samsung

Samsung SCS-26UC4 user guide

Foxun

Foxun SX-GES24 operating instructions

MuxLab

MuxLab 500771 Operation manual

foxunhd

foxunhd SX-AEX01 operating instructions

TERK Technologies

TERK Technologies LFIRX2 owner's manual

Devolo

Devolo Audio Extender supplementary guide

Edimax

Edimax EW-7438RPn V2 instructions

Shinybow USA

Shinybow USA SB-6335T5 instruction manual