Extron electronics XTRA FULL RACK XPA 2002 User manual

Product Category

XTRA™ Full Rack Series • Setup Guide

This guide provides basic instructions for an experienced installer to set up and operate the Extron XTRA Full Rack Series of

power ampliﬁers. All user guide references refer to the XTRA Full Rack Series User Guide.

• XPA 2002 outputs stereo audio at 200 watts rms per channel (4-ohm speakers) or 100 watts rms per channel (8-ohm

speakers) on channels 1 and 2. Output is 400 watts bridged mono (8-ohm speaker).

• XPA 2002-70V outputs 200 watts rms per channel on channels 1 and 2 for 70 V systems.

• XPA 2002-100V outputs 200 watts rms per channel on channels 1 and 2 for 100 V systems.

• XPA 2003C-70V outputs 200 watts per channel (4-ohm speakers) or 100 watts per channel (8-ohm speakers) on channels

1 and 2, and 200 watts (70 V line, mono) on channel 3.

• XPA 2003C-100V outputs 200 watts per channel (4-ohm speakers) or 100 watts per channel (8-ohm speakers) on

channels 1 and 2, and 200 watts (100 V line, mono) on channel 3.

• XPA 2004 outputs stereo audio at 200 watts per channel (4-ohm speakers) or 100 watts per channel (8-ohm speakers) on

channels 1, 2, 3, and 4. Output is 400 watts per bridge in bridged mono (8-ohm speakers) on bridge A (channels 1 and

2) and bridge B (channels 3 and 4).

• XPA 4002 outputs stereo audio at 400 watts rms per channel (4-ohm speakers) or 200 watts rms per channel (8-ohm

speakers) on channels 1 and 2. Output is 800 watts bridged mono (8-ohm speaker).

• XPA 4002-70V outputs 400 watts rms per channel on channels 1 and 2 for 70 V systems.

Installation

1. Power off — Turn off all equipment including the XPA ampliﬁer by toggling the power off and disconnecting the

power cord. Verify that the ampliﬁer is disconnected from the power source before proceeding.

2. Mount the ampliﬁer — For diagrams of typical application examples, see the “Application Examples” section in the user

guide. For further mounting instructions, see the “Mounting the XTRA Series of Power Ampliﬁers” section in the user

guide.

3. Wire the input — Wire the input to the 3.5 mm input connectors of the ampliﬁer, as shown in the following illustration.

See the “Rear Panel Features and Operation” section in the user guide for bridging information.

NOTE: Control signal ground pins may be labeled as or “G”. Audio ground pins may be labeled as or .

The wiring and function are the same, whichever way your product is labeled.

NOTE: The wires must not be tinned: tinned wire does not hold tight in the captive screws and can break easily

after several bends.

4. Wire the outputs — Wire speakers to the output connectors of the ampliﬁer using the included 2-pole (70 V or 100 V)

or 4-pole (8 ohm or 4 ohm) screw lock plug.

2-pole (70 V or 100 V) output connector wiring: 4-pole (8 ohm or 4 ohm) output connector wiring:

CAUTION: Do not short the “+” and “ ” outputs to each other. Doing so may damage the ampliﬁer.

For complete wiring details, see “Rear Panel Features and Operation” in the user guide.

1 2

(BRIDGE)

Do not tin the wires!

OUTPUT

70V

" (5 mm) MAX. Tip

Sleeve

Ring

Tip

Sleeve

Unbalanced Input Balanced Input

112

Do not tin the wires!

1 2

OUTPUT

68-783-50 Rev. E

03 12

XTRA™ Full Rack Series • Setup Guide (Continued)

Extron Headquarters

+1.800.633.9876 (Inside USA/Canada Only)

Extron USA - West Extron USA - East

+1.714.491.1500 +1.919.863.1794

+1.714.491.1517 FAX +1.919.863.1797 FAX

Extron Europe

+800.3987.6673

(Inside Europe Only)

+31.33.453.4040

+31.33.453.4050 FAX

Extron Asia

+800.7339.8766

(Inside Asia Only)

+65.6383.4400

+65.6383.4664 FAX

Extron Japan

+81.3.3511.7655

+81.3.3511.7656 FAX

Extron China

+4000.398766

Inside China Only

+86.21.3760.1568

+86.21.3760.1566 FAX

Extron Middle East

+971.4.2991800

+971.4.2991880 FAX

Extron Korea

+82.2.3444.1571

+82.2.3444.1575 FAX

Extron India

1800.3070.3777

Inside India Only

+91.80.3055.3777

+91.80.3055.3737 FAX

5. Bridge outputs (XPA 2002, XPA 2004, and XPA 4002) — Bridging the output of input 1 (XPA 2002 and XPA 4002)

or inputs 1 and 3 (XPA 2004) doubles the output of those inputs (see “Bridged Mode Output” in the

user guide for further details). The bridge output mode toggle switch is shown at right.

Bridge mode: XPA 2002 and XPA 4002

Bridging takes the signal from input 1 and outputs the combined output of 400 watts (XPA 2002)

or 800 watts (XPA 4002) from the + terminals of output channels 1 and 2 (see the diagram at right).

Toggle the bridged output mode switch up (bridged) or down (unbridged).

Bridge mode: XPA 2004

Bridging takes the signal from input 1 or input 3 or both and outputs the combined

output of 400 watts from the + terminals of output channels 1 and 2 (Bridge A), or

output channels 3 and 4 (Bridge B), or both (see the diagram at right). Toggle the bridged

output mode switch up (bridged) or down (unbridged) for the appropriate input channel.

NOTE: When bridging outputs, the minimum load impedance is 8 ohms.

6. Reconnect all power cords and switch on all other equipment before powering up the power ampliﬁer. The ampliﬁer

must be powered up last. The front panel LED of the ampliﬁer should light green.

NOTE: Adjust the attenuation level to =before powering the ampliﬁer back up in step 6. See “Rear Panel Features

and Operation” in the user guide for details. On some models, this adjustment is referred to as “level”, but

the function is the same, whichever way your product is labeled.

7. Adjust the attenuation level using the rear panel adjustment screws.

LEVEL

8. Set the high pass ﬁlter — Use a small screwdriver to toggle this switch between off

(no ﬁltering) and 80 Hz (default). The XPA 2002-70V, XPA 2002-100V, and XPA 4002-70V

have two switches, one for each output channel. The XPA 2003C-70V and the

XPA 2003C-100V have one switch for the 70 V (XPA 2003C-70V) or 100 V (XPA 2003C-100V)

line distribution output channel (channel 3). Setting the switch to 80 Hz prevents the

saturation of speaker input transformers by low frequency signals (see the diagram at right).

9. If desired, wire a contact closure device to the remote standby connector. Connecting pin 2 to ground (pin 1)

places the ampliﬁer in standby mode. Standby mode turns off all outputs, although the ampliﬁer is still

receiving power.

Use the included 2-pin, 3.5 mm captive screw connector to jumper the pins.

To Contact Closure Port

on Control Device STANDBY

BRIDGE A

8/4

8 Ohm

(BRIDGE 8 ONLY)

HPF

80 Hz

OFF

HPF

80 Hz

OFF

XPA 2002-70V

XPA 2002-100V

XPA 4002-70V

XPA 2003C-70V

XPA 2003C-100V

OFF

Other manuals for XTRA FULL RACK XPA 2002

This manual suits for next models

Other Extron electronics Amplifier manuals

Extron electronics

Extron electronics DTP HD DA8 4K 330 User manual

Extron electronics

Extron electronics NetPA Ultra Series User manual

Extron electronics

Extron electronics AVDA 6 MX DUAL User manual

Extron electronics

Extron electronics Distribution Amplifiers DVI DA4 Plus User manual

Extron electronics

Extron electronics P/2 DA2 MT User manual

Extron electronics

Extron electronics NetPA U 2002 SB User manual

Extron electronics

Extron electronics MDA 4V SDI User manual

Extron electronics

Extron electronics Extron P/2 DA2 PLUS User manual

Extron electronics

Extron electronics MDA 5SVA RCA User manual

Extron electronics

Extron electronics DVI DA Plus Series User manual

Extron electronics

Extron electronics IN3254 Parts list manual

Extron electronics

Extron electronics VGA Distribution Amplifiers P/2 DA4xi s User manual

Extron electronics

Extron electronics VersaTools MDA 3 Series User manual

Extron electronics

Extron electronics XTRA FULL RACK XPA 2002 User manual

Extron electronics

Extron electronics FOX DA8 Plus User manual

Extron electronics

Extron electronics MP 101 D User manual

Extron electronics

Extron electronics FOX DA8 User manual

Extron electronics

Extron electronics Extron P/2 DA2xi User manual

Extron electronics

Extron electronics DA2 HD 4K PLUS User manual

Extron electronics

Extron electronics XPA Ultra Series User manual

Extron electronics

Extron electronics CVDA 6 MX Dual User manual

Extron electronics

Extron electronics Video and Audio Line Drivers with Gain and EquaLization CVEQ... User manual

Extron electronics

Extron electronics Extron P/2 DA2xi User manual

Extron electronics

Extron electronics VGA Distribution Amplifiers P/2 DA4xi s User manual

Popular Amplifier manuals by other brands

ASTRO

ASTRO HVO V40 P operating manual

Marantz

Marantz SUPERSCOPE BLA-545 Service data

NAD

NAD CI980 Quick setup guide

Technics

Technics SE-CH770 Service manual

Harman Kardon

Harman Kardon HK6300 instruction manual

NAD

NAD T975 owner's manual

McIntosh

McIntosh MA6850 Brochure & specs

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N manual

Viatron

Viatron Autrix Technical manual

GME

GME GA9800 instruction manual

Atlas

Atlas CP700 Specification sheet

Roland

Roland KC-1000 owner's manual

Pyle

Pyle PFMRA350BW user manual

Advantage

Advantage S-250 manual

IRT Electronics

IRT Electronics DVA-3007 manual

Dimavery

Dimavery BA-100 Series user manual

Sony

Sony XM-S400D operating instructions

Schertler

Schertler ROY X quick guide