Extech Instruments 382252 User manual

User's Manual

Earth Ground Resistance Tester Kit

Model 382252

Model 382252 Ver. 1.1 08/09

Introduction

Congratulations on your purchase of the Extech 382252 Earth Ground Resistance Tester

Kit. This device can measure Earth Ground Resistance (in 3 ranges), Earth Voltage and

Resistance (up to 200kΩ), and AC and DC voltage. This device was designed to meet

EN61010-1 safety standards. Careful care and use of this meter will provide years of

reliable service.

Safety

Please read the following safety information carefully before attempting to operate the

meter and use the meter only as specified in this manual.

Environmental safety information

•Do not use meter outdoors when precipitation is likely

•Installation Category III

•Pollution degree 2

•Altitude: 2000 meters max.

•Ambient conditions: 32 to 104oF (0 to 40oC); RH: 80% max

•Observe the following international safety warning symbols

Safety Symbols

Caution: Refer to this manual before using this meter

Dangerous Voltages

Meter is protected throughout by double or reinforced insulation

Organizations that provide rules and guidelines for proper grounding

•The National Electrical Code (NEC)

•Underwriters Laboratories (UL)

•National Fire Protection Association (NFPA)

•American National Standards Institute (ANSI)

•Occupational Safety Health Administration (OSHA)

•Telecommunications Industry Standard (TIA)

Model 382252 Ver. 1.1 08/09

Meter Description

1. Digital Display – See Display Description below

2. HOLD key – Freezes measurement value on

display

3. 0 ADJ control- Adjusts Zero value on display

4. Backlight key – Turns on Backlight

5. TEST key – Enables Earth Resistance and Earth

Voltage Tests

6. Function Selector switch – Selects desired range

and function

Top View

1. VΩ/C Input

2. P Input

3. COM/E Input

Display Description

1. Test status Icon

2. Battery Charge indicator -

3. Voltage Unit indicator

4. Audible Signal Icon

5. Ω/kΩ Units Indicators

6. Measurement Value

7. AC/DC Voltage Indicators

8. Low Battery Icon

9. HOLD Icon

12 3

Model 382252 Ver. 1.1 08/09

Operation

0 Adjustment

1. Connect the test leads to the meter as follows:

a. Green lead to the 'E' terminal

b. Yellow lead to the 'P' terminal

c. Red lead to the 'C' terminal

2. Set the function selector switch to the desired measurement range.

3. Short the 3 test leads together.

4. Press the TEST key.

5. Use the 0 Adjust knob to adjust the displayed reading to 0Ω.

6. Press to TEST key again to end the 0 adjustment process.

Test Connection Diagram

1. 382252 Meter

2. Green Test Lead

3. Yellow Test Lead

4. Red Test Lead

5. Existing Ground

6. P1 Auxiliary Earth Bar

7. C1 Auxiliary Earth Bar

Test Preparation and Setup

1. Connect the test leads to the meter (1) as follows:

•Green lead (2) to the 'E' terminal

•Yellow lead (3) to the 'P' terminal

•Red lead (4) to the 'C' terminal

2. Drive the Auxiliary Earth Bars P1 (6) & C1 (7) into the ground. Align the bars

equidistant to the existing Earth ground connection and in a straight line as shown in

the diagram above. If the auxiliary bars are placed in close proximity to the ground

stake, measurement inaccuracies will result.

3. Connect the clamp ends of the test leads to the Earth bars and existing ground

connection as shown above:

•Green lead (2) to the existing ground (5)

•Yellow lead (3) to Earth Bar P1 (6)

•Red lead (4) to the Earth Bar C1 (7)

234

567

Model 382252 Ver. 1.1 08/09

Earth Voltage Test

1. Set the function on the selector’s switch to the EARTH VOLATAGE position.

2. Confirm that the voltage measurement is less than 10V AC; otherwise accurate Earth

resistance measurements cannot be made. If voltage is present (higher than 10V AC),

the source of the voltage must be found and corrected before testing can continue.

3. Press to TEST key to end the test. Note the LCD reading.

Earth Resistance Test

1. Set the meter's function switch to the desired resistance range.

2. Press the TEST button. . The “ “ icon will flash and the audible signal will sound.

3. Note the displayed reading.

4. If high resistance is detected, note the value and take appropriate steps to correct the

ground connection if necessary.

5. Press to TEST key to end the test.

6. Readings of “1”…Ωare typical when the test leads are not connected to the meter.

HOLD Function

The Hold function freezes the latest measurement reading on the LCD.

1. Press the HOLD key to freeze the reading on the LCD

2. Press the HOLD key again to exit the HOLD function.

3. The HOLD function does not retain measurement data if the meter is turned off.

Backlight

1. Press the “ “ key to turn on the backlight.

2. The backlight will turn off after approximately 15 seconds.

200kΩResistance Measurement

1. Connect the red test lead to the VΩ connector and the black test lead to the COM

connector.

2. Set the function selector switch to the 200kΩ position.

3. Connect the test probes to the circuit or component under test.

4. Note the displayed Resistance value.

AC Voltage Measurement

1. Connect the red test lead to the VΩ connector and the black test lead to the COM

connector.

2. Set the function selector switch to the 750V AC position.

3. Connect the test probes to the circuit under test.

4. Note the displayed Voltage value.

DC Voltage Measurement

1. Connect the red test lead to the VΩ connector and the black test lead to the COM

connector.

2. Set the function selector switch to the 1000V DC position.

3. Connect the test probes to the circuit under test.

4. Note the displayed Voltage value.

Model 382252 Ver. 1.1 08/09

Maintenance

Battery Replacement

When the low battery icon ' ' appears on the LCD, the meter's batteries must be

changed.

1. Remove power and disconnect the test leads from the meter.

2. Remove the tilt stand from the rear of the meter.

3. Remove the 4 battery compartment screws with a Phillips head

screwdriver.

4. Remove the battery compartment cover and replace the six 1.5V 'AA'

batteries.

5. Affix compartment cover and tighten screw.

6. Reattach the tilt stand.

Cleaning and Storage

Periodically wipe the meter's case with a damp cloth and mild detergent; do not use

abrasives or solvents. If the meter is not to be used for a period longer than 60 days,

remove the batteries and store them separately.

Specifications

General Specifications

Measurements Earth Ground Resistance (in 3 ranges), Earth Voltage,

AC Voltage to 750V and DC Voltage to 1000V

Display Large LCD with dual display

Sampling Time 2.5 times per second

Test lead length Red lead: 50' (15m), Yellow: 33' (10m), Green: 16' (5m)

Over-range indication '1' displayed as most significant digit

Power supply Six 1.5V 'AA' batteries (included)

Low battery indication LCD displays icon

Auto Power Off After approximately 15minutes of use

Safety EN-61010-1 category III

Weight 24.7oz. (700g) with batteries

Dimensions 7.9 x 3.62 x 2" (200 x 92 x 50 mm)

Supplied accessories Multimeter Test leads (2), Earth Ground test leads (3),

auxiliary earth bars (2), six 'AA' batteries, and carrying case

Operating Conditions 32ºF to 104ºF (0ºC to 40ºC), with < 80% RH

Storage Conditions 14ºF to 140ºF (-10ºC to 60ºC), with < 70% RH

Model 382252 Ver. 1.1 08/09

Measurement Specifications

Measurement Range Resolution Accuracy

Earth Ground

Resistance

20Ω 0.01Ω± (2% reading + 10 digits)

200Ω0.1Ω± (2% reading + 3 digits)

2000Ω1Ω

Earth Voltage

Frequency: 40 to

500Hz

0 to 200VAC

0.1V ± (3% reading +3digits)

Resistance 0 to 200kΩ0.1kΩ± (1% reading +2 digits)

Overload Protection: 250 Vrms

AC Voltage

40 Hz to 400Hz

0 to 750V 1V ± (1.2% reading +10 digits)

Overload Protection: 750 Vrms, Input Impedance: 10MΩ

DC Voltage 0 to 1000V 1V ± (0.8% reading +3 digits)

Overload Protection: 1000 Vrms, Input Impedance: 10MΩ

Support line (781) 890-7440

Technical support: Extension 200; E-mail: support@extech.com

Repair & Returns: Extension 210; E-mail: repair@extech.com

Product specifications subject to change without notice

For the latest version of this User Guide, Software updates, and other

up-to-the-minute product information, visit our website: www.extech.com

Extech Instruments Corporation, 285 Bear Hill Road, Waltham, MA 02451

Warranty

EXTECH INSTRUMENTS CORPORATION (A FLIR COMPANY)warrants this instrument to

be free of defects in parts and workmanship for one year from date of shipment (a six

month limited warranty applies to sensors and cables). If it should become necessary to

return the instrument for service during or beyond the warranty period, contact the

Customer Service Department at (781) 890-7440 ext. 210 for authorization or visit our

website www.extech.comfor contact information. A Return Authorization (RA) number

must be issued before any product is returned to Extech. The sender is responsible for

shipping charges, freight, insurance and proper packaging to prevent damage in transit.

This warranty does not apply to defects resulting from action of the user such as misuse,

improper wiring, operation outside of specification, improper maintenance or repair, or

unauthorized modification. Extech specifically disclaims any implied warranties or

merchantability or fitness for a specific purpose and will not be liable for any direct, indirect,

incidental or consequential damages. Extech's total liability is limited to repair or

replacement of the product. The warranty set forth above is inclusive and no other

warranty, whether written or oral, is expressed or implied.

Calibration and Repair Services

Extech offers repair and calibration services for the products we sell. Extech also

provides NIST certification for most products. Call the Customer Service Department for

information on calibration services available for this product. Extech recommends that

annual calibrations be performed to verify meter performance and accuracy.

more infor for Extech 382252

Phone: 01235 838 555

Email: cs@airconcern.co.uk

Web. www.airconcern.co.uk

Air Concern Ltd, Building 173 Curie Avenue Harvell Didcot, Oxfordshire

Table of contents

Other Extech Instruments Test Equipment manuals

Extech Instruments

Extech Instruments TK36 User manual

Extech Instruments

Extech Instruments 380320 User manual

Extech Instruments

Extech Instruments 382357 User manual

Extech Instruments

Extech Instruments 412300 User manual

Extech Instruments

Extech Instruments 380385 User manual

Extech Instruments

Extech Instruments 380260 User manual

Extech Instruments

Extech Instruments 480400 User manual

Extech Instruments

Extech Instruments HDV600 User manual

Extech Instruments

Extech Instruments HDV540 User manual

Extech Instruments

Extech Instruments MS420 User manual

Extech Instruments

Extech Instruments ET10 User manual

Extech Instruments

Extech Instruments 422123 User manual

Extech Instruments

Extech Instruments prc20 User manual

Extech Instruments

Extech Instruments 7630 User manual

Extech Instruments

Extech Instruments ET60 User manual

Extech Instruments

Extech Instruments ET25 User manual

Extech Instruments

Extech Instruments MS6100 User manual

Extech Instruments

Extech Instruments PRC15 User manual

Extech Instruments

Extech Instruments FT10 User manual

Extech Instruments

Extech Instruments GX930 User manual

Extech Instruments

Extech Instruments 433201 User manual

Extech Instruments

Extech Instruments ET15 User manual

Extech Instruments

Extech Instruments ET30B User manual

Extech Instruments

Extech Instruments 380375 User manual

Popular Test Equipment manuals by other brands

SMART

SMART KANAAD SBT XTREME 3G Series user manual

Agilent Technologies

Agilent Technologies BERT Serial Getting started

Agilent Technologies

Agilent Technologies N3280A user guide

Vernier

Vernier Go Direct Voltage manual

Lifeloc

Lifeloc R.A.D.A.R. quick start guide

Fluke

Fluke T5-600 Service information

Mercury

Mercury TSL01 user manual

MAHA

MAHA MBT Series Original operating instructions

Fuji Electric

Fuji Electric P-61 instruction manual

ETC

ETC SealerAtor user manual

Skyfine

Skyfine ETHYWAY V2 user manual

Appion

Appion G5 Twin Operation manual

PCB Piezotronics

PCB Piezotronics 8159-0112A Installation and operating manual

BW Technologies

BW Technologies MicroDock II user manual

Sun Nuclear

Sun Nuclear 1027 user guide

Biomark

Biomark HPR LITE READER user manual

Hioki

Hioki 3169-20 instruction manual

Ashcroft

Ashcroft ATE-100 operating manual