Extech Instruments 401025 User manual
User's Manual
Model 401025
Digital Light Meter
401025-EU-EN-V2.2-2/12
2
Lu x
1
2
5
4
8
7
3
6
Introduction
Congratulations on your purchase of Extech’s Digital Light Meter. This professional meter, with proper
care, will provide years of safe reliable service.
Meter Description
1. LCD Display
2. Data Hold Switch
3. Power Off/Range Switch
4. Analog Output Terminal
5. Battery Compartment (rear)
6. LUX/Fc Switch & Response Switch
7. Light Sensor
8. Zero adjust
Operation
1. Select Units (Lux or Ft-candle) and Response Time (Fast or Slow) on the slide switch.
Typical selection is Slow and Fc using the gray lettering.
2. Select the maximum range on the "Range Switch"
3. Hold the "Light Sensor" so that the sensor faces the light source to be measured.
4. The Display will indicate measured values. Use a range display multiplier if on the Lux
20,000 and 50,000 ranges or on the Fc 5000 range.
5. To "hold" a measurement, slide the "Data Hold Switch" to the "hold" position. The reading
will "freeze" in the display until the "Data Hold Switch" is released.
Note 1: An Over Range indication is a display of "I ". If this occurs, switch to a higher range.
Note 2: For measurements made on the Fc 5000 range, the displayed reading must be multiplied
by 10.
Note 3: For measurements made on the Lux 20000 or 50000 range, the displayed reading must
be multiplied by 10 and 100 respectively.
Note 4: The meter will indicate values above the maximum ranges. The accuracy of these
measurements is unknown.
Range Display Multipliers
Range Units Multiplier
200 Fc Direct reading
2000 Fc & Lux Direct reading
5000 Fc Reading x10
20,000 Lux Reading x10
50,000 Lux Reading x100
Example: If a measurement on the 5000 Fc range displays 350, then the actual measured value
is; 350 X 10 = 3500 Fc.
401025-EU-EN-V2.2-2/12
3
Selecting a Measurement Range
The meter has three measurement ranges (0-200, 0-2000, and 0-5000 Fc) and (0-2000, 0-20000, and
0-50000) Lux). The proper range selection will produce the most accurate reading. Always select the
range that produces the maximum number of digits without exceeding the maximum count for that
particular range. For example, a reading of 1456 Fc should be read on the 0 - 2000 range, not the 0-
5000 range.
Zero procedure
The meter zero (display with no light input) may change with time. Occasional checking and
adjustment may be required.
1. Completely cover the sensor to block out any light.
2. Set the range switch to the lowest Lux or Fc range
3. Using a small screwdriver, adjust the “Zero” control for a zero display. The last digit may
change slightly. This is normal and does not affect the accuracy of the meter.
Analog Output
The analog output jacks on the front panel produce a 0.1mV DC per digit signal that can be used for
recording or datalogging purposes.
Lighting Type Correction Factors
The 401025 light meter is calibrated under a precise "Standard tungsten light source of 2856OK". If the
meter is to be used under a different type of light the correction factor of from the table below should
be applied to the readings obtained.
Mercury Lamp x1.14
Fluorescent Lamp X0.92 to 1.12
Daylight x1.00
Sodium x1.22
Metal Halide x1.00
Replacing the Battery
When the left corner of the LCD display shows "LO BAT", it indicates the battery output is below the
design limit and the battery needs to be replaced. However, reliable measurement can still be taken for
another few hours before the tester becomes inaccurate.
1. Open the Battery Cover at the back of tester and remove the battery.
2. Replace with a 9V battery and install the cover.
You, as the end user, are legally bound (EU Battery ordinance) to return all used
batteries, disposal in the household garbage is prohibited! You can hand over your
used batteries / accumulators at collection points in your community or wherever batteries
/ accumulators are sold!
Disposal: Follow the valid legal stipulations in respect of the disposal of the device at the
end of its lifecycle
401025-EU-EN-V2.2-2/12
4
Specifications
General Specifications
Display 13 mm (0.5") LCD (Liquid Crystal Display).
Measurement Lux, Ft-candle (Fc).
Ranges Lux: 0 to 50,000 Lux, 3 ranges. Foot-candle: 0-5,000 Fc, 3
ranges.
Sensor Exclusive photo diode & color correction filter, spectrum
designed to meet C. I. E.
Zero Adj. Manual adjustment.
Sampling Time Approx. 0.4 sec.
Response Time Fast: 0.25s; Slow: 1s
Over input indication Indication of "1 "
Analog Output 0.1 mV/1 digit, max. output :200mV.
Operating Temperature 0OC to 50OC (32OF to 122OF)
Operating Humidity Less than 80% RH.
Power Supply 006P DC 9V battery
Power Current Approx. 2 mA DC
Weight 220 g / 0.52 LB
Dimension Main instrument: 163x70x30mm (6.4x2.8x1.2 inch).
Sensor Probe: 85x55x12 mm (3.2x2.2x0.5 inch).
Optional Accessories Vinyl pouch carrying case, 409996
Range Specifications
Lux
Range In-range Display Resolution Accuracy
2,000 Lux 0-1,999 Lux 1 Lux ± (5% + 2digits)
20,000 Lux 2,000-19,990 Lux 10 Lux ± (5 % + 2digits)
50,000 Lux 20,000-50,000 Lux 100 Lux ±- (5 % + 2digits)
Foot-candle (Fc)
Range In-range Display Resolution Accuracy
200 Fc 0-199.9 Fc 0.1 Fc ± (5% + 2digits)
2,000 Fc 200-1,999 Fc 1 Fc ± (5% + 2digits)
5,000 Fc 2,000-5,000 Fc 10 Fc ± (5% + 2digits)
Frequency Spectrum
300 400 500 600 700 800
1
0.8
0.6
0.4
0.2
0
Wavelength (nm)
401025-EU-EN-V2.2-2/12
5
Appendix A: Typical Light Levels
Lux Foot
Candles
Lux Foot
Candles
Factories Home
20-75 2-7 Emergency Stairs,
Warehouse
100-150 10-15 Washing
75-150 7-15 Exit/Entrance Passages 150-200 15-20 Recreational
Activities
150-300 15-30 Packing Work 200-300 20-30 Drawing Room,
Table
300-750 30-75 Visual Work: Production
Line
300-500 30-50 Makeup
750-1,500 75-150 Typesetting: Inspection
Work
500-1,500 50-150 Reading, Study
1,500-
3,000
150-300 Electronic Assembly,
Drafting
1,000-
2,000
100-200 Sewing
Office Restaurant
75-100 7-10 Indoor Emergency Stairs 75-150 7-15 Corridor Stairs
100-200 10-20 Corridor Stairs 150-300 15-30 Entrance, Wash
Room
200-750 20-75 Conference, Reception
Room
300-750 30-75 Cooking/Dining
Room
750-1,500 75-150 Clerical Work 750-1,500 75-150 Show Window
1,500-
2,000
150-2000 Typing, Drafting
Store Hospital
75-150 7-15 Indoors 30-75 3-7 Emergency Stairs
150-200 15-20 Corridor/Stairs 75-100 7-10 Stairs
200-300 20-30 Reception 100-150 10-15 Sick Room,
Warehouse
300-500 30-50 Display Stand 150-200 15-20 Waiting Room
500-750 50-75 Elevator 200-750 20-75 Medical Exam Room
750-1,500 75-150 Show Window, Packing
Table
750-1,500 75-150 Operating Room
1,500-
3,000
150-300 Storefront, Show Window 5,000-
10,000
500-1000 Eye Inspection
Appendix B - Common Terms and Conversion Factors
1 lux (lx)
10-4 lm/cm2
10-4 phot (ph)
9.290 x 10-2 lm/ft2
Illuminance (Visible Flux Density) 1 lm/m2=
9.290 x 10-2 foot-candles
Luminance (Visible Flux Density per Solid Angle) 1 lm/m2/sr = 1 candela/m2
Luminous Intensity (Visible Flux per Solid Angle) 1 lm/sr = 1 candella
Luminous Flux ( Visible Flux) 1 lumen (lm) = 1.464 x 10-3 watts @ 555 nm
Copyright ©2012 Extech Instruments Corporation (a FLIR company)
All rights reserved including the right of reproduction in whole or in part in any form.
www.extech.com
Table of contents
Other Extech Instruments Multimeter manuals
Extech Instruments
Extech Instruments EX470A User manual
Extech Instruments
Extech Instruments MN45 User manual
Extech Instruments
Extech Instruments 380926 User manual
Extech Instruments
Extech Instruments EX540-NIST User manual
Extech Instruments
Extech Instruments 430 User manual
Extech Instruments
Extech Instruments 382100 User manual
Extech Instruments
Extech Instruments 412355A Oyster Series User manual
Extech Instruments
Extech Instruments MP510A User manual
Extech Instruments
Extech Instruments 450 User manual
Extech Instruments
Extech Instruments EX310 User manual
Extech Instruments
Extech Instruments MultiPro MP510 User manual
Extech Instruments
Extech Instruments 382075 User manual
Extech Instruments
Extech Instruments MiniAmp Series User manual
Extech Instruments
Extech Instruments 45170 User manual
Extech Instruments
Extech Instruments 381676A User manual
Extech Instruments
Extech Instruments MA220 User manual
Extech Instruments
Extech Instruments 380946 User manual
Extech Instruments
Extech Instruments 38070 User manual
Extech Instruments
Extech Instruments MN25 User manual
Extech Instruments
Extech Instruments MN62 User manual
Popular Multimeter manuals by other brands
Gossen MetraWatt
Gossen MetraWatt METRAmax 6 operating instructions
PeakTech
PeakTech 4000 Procedure of calibration
YOKOGAWA
YOKOGAWA 90050B user manual
Gossen MetraWatt
Gossen MetraWatt METRALINE DMM16 operating instructions
Fluke
Fluke 8846A Programmer's manual
Tempo Communications
Tempo Communications MM200 instruction manual
