ExpertDAQ EX9486C-W-MTCP User manual
Operation Manual of EX9486C-W-MTCP
Wi-Fi to Modbus Gateway(Modbus RTU/ASCII to Wi-Fi)
Version 1.0
22th April 2016
EX9486C-W-MTCP
Manual
Page 2 EX9486C-W-MTCP • Manual Version 1.1 • 22.04.2016 www.topsccc.com.tw
Introduction
Modbus RTU/ASCII to Wi-Fi(Modbus TCP)converter is provided new ways of connecting serial
devices to a Wireless LAN(Wi-Fi 802.11 b/g ). Serial(Modbus RTU/ASCII) to Wi-Fi(Modbus TCP)
Converter is designed to operate serial ports through wireless (Wi-Fi 802.11 b/g) over 10/100Mbps
Ethernet networks. The data is transmitted via TCP/IP protocol. Therefore control is available via
Ethernet, Intranet and Internet. Serial (Modbus RTU/ASCII) to Wi-Fi(Modbus TCP) Converter is
packaged in a case well suited for industrial environments. All serial ports operate in common
RS-232 mode, industrial RS-422 and RS-485 modes configuration.
With the maturity of Wi-Fi technology of 802.11b/g, delivering cost effective becomes increasingly
important. Model EX9486C-W-MTCP of Modbus RTU/ASCII to Wi-Fi (Modbus TCP) converter
product is a more competitive price by careful selecting high quality with competitive prices
components in the world, the product design is ARM single-chip, made network connectivity possible
with affordable cost for virtually all kinds of devices. This user manual will guide you step by step for
setting the various functions of model EX9486C-W-MTCP product.
The following topics are:
□
□
□
Overview
□
□
□
Package Checklist
□
□
□
Product Features
□
□
□
Product Specifications
□
□
□
Wiring architecture
Overview
Modbus RTU/ASCII to Wi-Fi(Modbus TCP) Converter is provided a perfect solution to make your
industrial serial devices Internet ready instantly via wireless LAN. Model EX9486C-W-MTCP with
ARM chipset, Modbus RTU/ASCII to Wi-Fi(Modbus TCP) Converter makes them the ideal choice for
connecting your RS-232 or RS-422/485 serial devices such as PLCs, meters, and sensors—to an
IP-based Wi-Fi ⁄Ethernet LAN, making it possible for your software to access serial devices
anywhere and anytime over a wireless local LAN or the Internet.
Modbus RTU/ASCII to Wi-Fi(Modbus TCP) Converter support manual configuration via the handy
web browser console and many protocols including DHCP, HTTP, Modbus RTU/ASCII Slave to
Modbus TCP Master Modbus TCP Slave to Modbus RTU/ASCII Master. They are the best solution to
network your serial devices.
Package Check List
Serial to Wi-Fi(Modbus TCP) Converter product is shipped with the following items:
□
□
□1 unit of Serial to Wi-Fi Converter
□
□
□1 unit of dipole antenna(2.0dBi)
□
□
□1 unit CD(Operation Manual & Utility)
□
□
□
Din Rail Mounting Kit & Power Adaptor :Optional
NOTE: Notify your sales representative if any of the above items is missing or damaged.
EX9486C-W-MTCP
Manual
Page 3 EX9486C-W-MTCP • Manual Version 1.1 • 22.04.2016 www.topsccc.com.tw
Product Features
Data Conversion between RS-232/422/485 and Wireless Lan
Convert serial device (RS-232, RS-422, RS-485) data/signal into the TCP/IP package data/signal
and send them out with the Ethernet DataStream via Wi-Fi wireless; or convert the TCP/IP package
data/signal into serial device data/signal.
Wi-Fi Wireless LAN(802.11 b/g)
It based on the latest industry standard Wi-Fi Certified IEEE 802.11b / g specification; it offers
maximum channel speeds of up to 54 Mbps. The Wi-Fi function maintains interoperability within the
2.3∼2.5 GHz frequency band, offering full compatibility with 802.11b / g networks. This integrated
wireless solution of Serial to Ethernet Converter is widely deployed in business environments and is
the standard for wireless access in public places. It also supports key security features like Wi-Fi
Protected Access (WPA), WEP and 802.1x.
Dynamic IP Configuration
Support DHCP client mode, simplifying network address configuration and management.
Dual LAN Speed
Support 10/100 Mbps Ethernet, auto-detected.
Server / Client Dual Modes
Series can be configured as network server or network client. In the client mode, it can be installed in
network which is protected by NAT router or firewall, without the need of a real IP address.
Web-based Setup
Parameters setup is based on HTTPS protocol by using standard browsers (IE and Netscape). No
special software would be required. To use https to enter Web-Server of converter
(For example https：⁄⁄192.168.0.115)
Built-in Security Control
It is protected by both setup password and access password to prevent intruders.
Remote updated
Firmware can be reprogrammed directly via Ethernet network to keep up with latest network
standards.
EX9486C-W-MTCP
Manual
Page 4 EX9486C-W-MTCP • Manual Version 1.1 • 22.04.2016 www.topsccc.com.tw
Product Specifications
Hardware specification
WLAN
Standard Compliance : IEEE 802.11 b / g
Spread Spectrum Technology: DSSS, OFDM
Tx Power 11b: Maximum 19 dBm
Tx Power 11g/n: Maximum 16 dBm
Rx Sensitivity: -73 dBm @ 54Mbps, -86dBm @ 11Mbps
Transmission Rate: 54 Mbps (max.) with auto fallback (54,48, 36, 24, 18, 12, 11, 9, 6, 5.5, 2, 1 Mbps)
Transmission distance: Up to 100 meters (@12 Mbps, in open areas)
Security: WEP 64-bit/128-bit data encryption, AES, WPA2, WPS2.0, WAPI
Antenna Connector: Reverse SMA, 2 dbi Antenna
Network Mode: Infrastructure, Ad-Hoc, Soft AP(Setup)
Setup: HTTP Browser Setup(IE, Chrome, Firefox)
Security: Login Password
Serial Communication Parameters
No. of ports : 1 * RS-232/422/485 port, Male DB9/ 4-pin Terminal Block, S/W selectable
RS-232 Signals : TxD, RxD and GND only
RS-422 Signal : Tx+ , Tx- , Rx+ , Rx –
RS-485 Signal : Data+ , Data-
Serial Line Protection : 15 KV ESD for all signals
Parity: None, Even, Odd, Space, Mark
Data bits: 5, 6, 7, 8
Stop bits: 1, 1.5, 2
Flow control: XON/XOFF
Speed: 110 bps to 115.2+ Kbps
Built-in: RTC(Real Time Clock)
Power Requirements
Power input : 9~24V, 200mA@12 VDC
note: pin assignment of Power Supply if you select the Terminal Block
Environmental
Operating Temperature : -10 to 65°C , 10 to 95% RH
Storage Temperature : -20 to 70°C (-4 to 185°F), 5 to 95%RH
Regulatory Approvals
RoHS
FCC, CE
EX9486C-W-MTCP
Manual
Page 5 EX9486C-W-MTCP • Manual Version 1.1 • 22.04.2016 www.topsccc.com.tw
Software Features
Protocols : DHCP, HTTP, Modbus RTU/ASCII Slave to Modbus TCP Master
Modbus TCP Slave to Modbus RTU/ASCII Master
Mode : Modbus TCP Master/ Slave
Support 8 TCP Masters simultaneously
Support serial Master access to 8 TCP Slaves
Utilities : Windows 2000/2003/VISTA/WIN 7/WIN 8
Wiring Architecture
RS-232 Wiring Architecture
RS-422/RS-485 Wiring Architecture
When you finish the steps mentioned above and the LED indicators are as shown, the converter is
installed correctly. You can use the Utility Setup CD to setup the IP Address.
To proceed the advanced parameter setup, please use a web browser (IE or Netscape) to continue
the detailed settings.
EX9486C-W-MTCP
Manual
Page 6 EX9486C-W-MTCP • Manual Version 1.1 • 22.04.2016 www.topsccc.com.tw
EX9486C-W-MTCP Wi-Fi Converter Configuration
Installation of IP Search Tool
1. Please copy EX9486C-W-MTCP.exe to your PC. You can find the file in the CD ROM.
2. Double click EX9486C-W-MTCP.exe. The program will be extracted and installed in PC.
3. After successful installation, the shortcut of WiFi-Module Utility.exe will be on the desktop
Connection and Configuration
Please prepare a PC/NB with Wireless adapter, a Wireless Access Point and EX9486C-W-MTCP.
1. Connecting EX9486C-W-MTCP Gateway
Note: EX9486C-W-MTCP has no Ethernet port and is default as a Soft AP.
1-1. EX9486C-W-MTCP Gateway is default as a “Soft AP” when first connected to power. Its
broadcast SSID is AJ+MAC address
1.2. Please use PC/NB (with Wi-Fi adapter) to conduct SSID site survey. Looking for a SSID shown
as MAC address. (ie. AJ:XX:XX:XX:XX:XX:XX) Then Click Connect
EX9486C-W-MTCP
Manual
Page 7 EX9486C-W-MTCP • Manual Version 1.1 • 22.04.2016 www.topsccc.com.tw
1-3. Key in Soft AP password. Default is 12345678
1-4. Connecting to EX9486C-W-MTCP Gateway
EX9486C-W-MTCP
Manual
Page 8 EX9486C-W-MTCP • Manual Version 1.1 • 22.04.2016 www.topsccc.com.tw
Now you have successfully connect to EX9486C-W-MTCP
EX9486C-W-MTCP
Manual
Page 9 EX9486C-W-MTCP • Manual Version 1.1 • 22.04.2016 www.topsccc.com.tw
2. Searching & Configuring EX9486C-W-MTCP Gateway
2-1. IP Searching
2-1-1. Double Click on to execute IP search tool
2-1-2. Click on “IP Search” or “Broadcast”. WiFi-Module Utility will start to scan the network.
2-1-3. Device found
EX9486C-W-MTCP
Manual
Page 10 EX9486C-W-MTCP • Manual Version 1.1 • 22.04.2016 www.topsccc.com.tw
2-1-4. Single click on device IP address. Then click “Goto” to open browser.
2-1-5. Login page is shown. Please input ID and Password. (default ID: admin; password: admin).
Now you have successfully searched the device
Table of contents
Popular Gateway manuals by other brands
LST
LST M500RFE-AS Specification sheet
Kinnex
Kinnex Media Gateway quick start guide
2N Telekomunikace
2N Telekomunikace 2N StarGate user manual
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Original instructions
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE user guide
Telsey
Telsey CPVA 500 - SIP Technical manual
