ExamVision Essential User manual
1
Congratulations on
your new LED system
2
Introduction
Getting started - Using your light for the rst time
Light cable direction
Replaceable cable
Help and guidance
Warranty
Your control unit and light
PowerBand
Focus™ Xtend
Essential One
Essential Alpha
Symbols and instructions for proper use
3
4
4
4
5
6
10
12
16
18
Content
3
You have chosen a high-quality light system, tailored to deliver the
exact amount of illumination, right where you need it.
ExamVision´s light systems have from 2 to 24 hours operating time,
depending on chosen light system and light intensity.
Our light systems are designed for either hands-free or touch-free
operation for sterile environments.
To achieve the optimum result from your new light system, please
follow the guiding instructions and videos carefully – or ask your
local ExamVision dealer for assistance.
Introduction
Light cable direction
With the exception of Essential One LED, which is wireless, the light
cable can be attached to the right or left loupe temple. For optimal
balance, we recommend that the cable then runs around the back
of your neck and attaches to the control unit on the opposite side.
Focus™ and Essential
Nano lights:
To change the cable direction,
loosen the small screw and
gently turn the ring to the
desired position. Ensure that
the ring touches the cable and
then tighten the screw.
Essential Alpha light:
To change the cable direction,
simply direct the cable to the right or left loupe temple.
Replaceable cable
Focus™ and Essential Nano lights: If your cable becomes damaged
you can replace it easily. Please contact your local ExamVision
dealer who can arrange a replacement.
Ring
Loosen
the screw
Help and guidance
Visit our Service Center on the ExamVision YouTube
channel for helpful videos. To watch now, just scan
the QR code.
For further technical specications see examvision.com
Getting started – Using your light for the rst time
4
5
Warranty
PowerBand control unit/Focus™ Xtend control unit/Focus™
True & Bright and Essential Nano light system and accessories
Covered by 3 years manufacturer warranty.
Focus™ True & Bright and Essential Nano replaceable cable
and backplate
Covered by 1 year manufacturer warranty.
Essential Alpha control unit, battery, light, cable and accessories
Covered by 1 year manufacturer warranty.
Essential One
Covered by 2 years manufacturer warranty.
Essential One battery, charger and accessories
Covered by 1 year manufacturer warranty.
Normal wear and tear, damage due to improper use or maintenance is
not covered by warranty. In the event of malfunction, please return the
device to your ExamVision dealer for repair.
Please also see examvision.com/warranty
6
Charging Port LED Port
Power
Button
Touch-Free
Motion Sensor
PowerBand
7
Operating your PowerBand
Power on
Press the Power Button
once.
Switch between
operating sides
To switch the operating
mode between Power
Button and Touch-Free
sensor, press the Power
Button 3 times
in quick succession.
When the light flashes
RED, the Power Button
is active.
When the light flashes
GREEN, the Motion
Sensor is active.
Changing light intensity
A single click changes
through light intensity
from low to high.
Power off
Press and hold for
2 seconds.
Right side
Touch-Free Motion Sensor
Left side
Power Button
3
3
1
2´
3´
Changing light intensity
Moving your hand
past the sensor
changes through
the light intensity
from low to high.
Power off
Hold your hand over
the sensor for 3 seconds.
1
11 1
8
Memory
When you turn off the PowerBand, it will retain the settings (light
intensity and operating mode).
Working time
Working time of your battery varies with light intensity. The lowest
setting can give you up to 24 hours continuous use, and the highest
setting approximately 12 hours.
Battery level status
Battery charging status
Please note: The lamp unit cannot be turned on, while the
PowerBand is charging.
Average charging time for an empty battery is 2.5 hours.
Operating your PowerBand
Light continuously green
100% - 20% charged
Light continuously yellow
20% - 10% charged
Light continuously red
10% - 0% charged
Light flashes red Light flashes yellow Light flashes green Continuously green
10
%
- 0
%
charged
10
%
- 20
%
charged
20
%
- 99
%
charged
100
%
charged
24 hours 12 hours
9
LED
Port
Charging
Port
Power Button
Light Intensity
Indicator
Pressable
Front Panel
Battery Level
Indicator
Focus™ Xtend
10
Other manuals for Essential
2
Table of contents
Other ExamVision Medical Equipment manuals
