Evve Long Range MK Series User manual
Vlierberg 4-06A
3755 BS Eemnes
The Netherlands
Phone: +31 0 85 0441855 (NL)
Web : www.evvelongrange.com
MK-Series
Installation Manual MK-Series 2/24
ABOUT THIS DOCUMENT ........................................................................................................................... 3
ADDITIONAL INFORMATION & RELATED DOCUMENTS ......................................................................... 3
FFC COMPLIANCE ........................................................................................................................................ 2
SUPPORT SERVICES ..................................................................................................................................... 2
SAFETY INSTRUCTIONS ............................................................................................................................... 2
1. PROTOCOL ............................................................................................................................................... 5
2. VIDEOSTREAMS THROUGH CHARM 10CE............................................................................................ 5
2.1 CONNECTING TO THE CHARM ........................................................................................................ 5
2.2 OPERATING IN MULTICAST ............................................................................................................. 5
2.3 RTSP VIDEOSTREAM.......................................................................................................................... 6
2.4 UPDATING SOFTWARE...................................................................................................................... 6
2.5 ADJUSTING IP ADDRESS.................................................................................................................... 7
2.6 CONFIGURING THE CHARM ............................................................................................................. 8
2.7 NTP SERVER ADDRESS ...................................................................................................................... 9
3. PASSTRHOUGH PORT MOXA ............................................................................................................... 10
3.1 INSTALLING NPORT ADMINISTRATOR.......................................................................................... 10
3.2 SEARCHING FOR DEVICE SERVERS OVER A LAN .......................................................................... 10
3.3 ADJUSTING GENERAL SETTINGS.................................................................................................... 11
3.4 CONFIGURING SERIAL COMMUNICATION PARAMETERS .......................................................... 13
3.5 MAPPING COM PORT TO DEVICE .................................................................................................. 15
3.6 CONFIGURATION BY WEB CONSOLE ............................................................................................ 18
4. OPERATING THE CAMERA WITH KEY-BOARD KBD300A................................................................... 19
4.1 USE THE DIFFERENT SPEEDS.......................................................................................................... 19
4.2 SET OR CHANGE END STOPS ......................................................................................................... 20
4.3 ABSOLUTE CONTROLS.................................................................................................................... 20
5. CAMERA OPERATING COMMANDS ..................................................................................................... 21
5.1 CAMERA COMMANDS..................................................................................................................... 21
5.2 LENS COMMANDS........................................................................................................................... 22
6. LASER OPERATING COMMANDS ......................................................................................................... 23
EVVE LONG RANGETM
Installation Manual MK-Series 3/24
For information on the camera installation, please see Installation Manual
MK-Series. This manual is available from the Evve Long Range website at:
www.evvelongrange.com/downloads
ABOUT THIS DOCUMENT
ABOUT THIS DOCUMEN
This manual contains information on the operation and the different
interfaces of the following Evve Long RangeTM products:
2000HD - High Definition Camera System
The information in this manual is subject to change without notice. Please
refer to our website for the latest information.
NOTE: All graphics contained within this document, including screenshots and
other displays, are for reference use only and are subject to change.
Copyright 2020 by Evve Long Range B.V. (ELR). ELR has intellectual property rights to technology
embodied in the product described in this manual.
Evve Long RangeTM and Evve International BVTM are trademarkt of BOTHA BV.
Installation Manual MK-Series 2/24
This equipment has been tested and found to comply with the limits for a Class A digital device
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference, in which case the user will be required to correct the interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation. Changes or modifications to this device void the warranty.
High Definition Demonstration Camera Positioning System
Installation Manual MK-Series 3/24
1. Please read these instructions prior to use.
2. Please keep these instructions accessible.
3. Please heed all warnings.
4. Please follow all instructions.
5. Installation should be done only by qualified personnel and conform to all local
codes.
CAUTION: These servicing instructions are for use by qualified service personnel
only.
To reduce the risk of electric shock, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so.
6. Use only mounting methods and materials capable of supporting at least four times the
combined weight of the pan-tilt unit, mounted payloads, and cabling.
7. For outdoor use, use only corrosion resistant hardware to fasten the mount and
payloads (e.g., stainless steel screws).
8. The unit should not be installed in environments that present conditions beyond
the environmental specification of pan-tilt unit. Installation near heat sources such
as radiators, heat registers, stoves, or other apparatus (including amplifiers) can
exceed the unit’s temperature ratings.
9. Refer all servicing to qualified service personnel. If the unit is damaged, remove power
immediately, and contact ELR.
10. A readily accessible power disconnect shall be incorporated into the installation wiring.
11. Only use replacement parts recommended by ELR.
Installation Manual MK-Series 4/24
Installation should be done only by qualified installers and conform to all local codes.
It is the users’ responsibility to ensure that the mounting methods are safe and adequate for
the location.
Use only stainless steel hardware to fasten the mount to an outdoor surface.
All servicing should be performed by qualified service personnel. Procedures in this manual
do not require entry into the housing of the camera positioning system. The unit contains
potential high voltage. It also contains sensitive devices that can be damaged by static
discharge. To reduce the risk of electric shock and damage to the unit by static discharge do
not perform any servicing other that described in these instructions. If the unit is defective,
please contact the Customer Service Department for technical assistance.
Liability: It is the sole responsibility of the installer to provide proper installation in compliance
with all local codes and regulations.
The Evve Long Range products are part of the next generation of Long Range camera systems,
ranging from high-definition (HD) to standard-definition (SD) camera positioning systems. The
systems are IP (Internet Protocol) based with a full function built-in operating system. Operator
functions features are controlled from the On Screen Display (OSD).
A drive system positioned within the MK-2000HD Series camera permits full 360° continuous pan
and 90° tilt movements. The camera systems comply with MIL-STD-18F standards for temperature,
shock, and vibration specifications. For environmental protection the camera systems use an IP67
camera head enclosure and IP66 positioner enclosure.
For more information on specifications and datasheets, please refer to specific product pages at Evve
Long Range website: www.evvelongrange.com/downloads.
At 50km the pixels per meter in
height will be 8. Assuming man is
2m approx. then 8 pixels is
Detection.
At 5km the pixels per meter in
height will be 40. Assuming man
is 2m approx. then 80 pixels is
Identification, i.e. it’s a man or
woman.
SAFETY INSTRUCTIONS
CLASS 3 (EYE & SPECULAR REFLECTION HAZARD):
Never aim the laser at a person’s eye or stare at the laser from within the beam.
Keep the beam path above or below eye level for one seated or standing.
Laser safety eyewear is needed if MPE (Maximum Permissible Exposure) is exceeded.
Don’t view beam directly with optical instruments unless a protective filter is used.
Only experienced and authorized individuals are permitted to operate the laser.
Secure the laser from operation by unauthorized personnel. A key switch should be used if
unauthorized personnel may gain access to the laser.
Always strive to enclose as much of the beam path as practical and to operate the laser in a
controlled access area.
During alignment, avoid placing one’s eye near the axis of the beam path, where specular
reflections are most likely to occur. Alignment eyewear should be considered.
Unnecessary specular (i.e., mirror-like) reflecting objects should be removed from the beam
path.
Mount the laser on a firm support to ensure the beam travels along its intended path.
Post laser hazard warning signs at entrances to laser use areas.
Installation Manual MK-Series 5/24
2.1 CONNECTING TO THE CHARM
You need a computer with Ethernet connection to the CHARM, and a web browser. Furthermore,
you need to know the IP address of the CHARM the default is 10.0.0.2.
Open the web browser and enter http://10.0.0.2 where 10.0.0.2 is the IP address of the CHARM.
The username is “v4” and the password “vision4ce”.
2.2 OPERATING IN MULTICAST
Looking at the start screen, towards the middle, you can see the option to ‘Edit’ the template.xml
file. Click the Edit button, and then follow the instructions in the file to:
Copy to another file.
Edit the copied file to:
oRemove the lower case x from the xStreamRTSPCfg0 entry.
oChange the bUseUnicast=”true” to bUseUnicast=”false”.
Save the file.
Ensure that the new file is ‘selected’ in the WebUpdater interface.
This MK-2000HD Series ELR camera has been adjusted to Pelco D 9600 Protocol.
Installation Manual MK-Series 6/24
2.3 RTSP VIDEOSTREAM
To obtain a direct RTSP VideoStream of the charm, use the following URL:
10.0.0.2:8001/charmstream
in which 10.0.0.2 is the IP address of the CHARM10CE.
To get a VideoStream in RTSP, you can a media player like for example VLC.
2.4 UPDATING SOFTWARE
The following instrucitons are for updating the tracker software on a CHARM with Ethernet
connection. Operating system and tracker sofware update over serial connection are not covered
here.
PRE-REQUISITES
You will need a computer with Ethernet connection to the CHARM, an update file and a web
browser. You will need to know the IP address of the CHARM (the default is 10.0.0.2).
PERFORMING AN UPDATE
Choose “Update
CHARM” from
the CHARM Main
Page then click
on the “Choose
file” button and
navigate to the
update file.
Once it has finished uploading you will see
“Processing update …” for a few seconds then
“Running update” and finally the installer output in
the box below or a “connection lost” message
when the CHARM reboots itself after installation.
2. VIDEOSTREAMS THROUGH CHARM 10CE
Installation Manual MK-Series 7/24
2.5 ADJUSTING IP ADDRESS
To change the IP address click on the “Change IP address link” from the CHARM Main Page. Enter
the new IP address and subnet mask. For IP addresses in the 10.0.0.x range the subnet mask
should be 255.0.0.0 and for IP addresses in the 192.168.1.x range the subnet mask should be
255.255.255.0.
You can optionally add a gateway address if you need the CHARM to connect to the internet, to
get internet (NTP) time for instance.
Upon pressing the submit / Set IP button the IP address will be changed and the CHARM rebooted.
To view the CHARM Web Updater again you will need to log in again at the new IP address.
2. VIDEOSTREAMS THROUGH CHARM 10CE
Installation Manual MK-Series 8/24
2.6 CONFIGURING THE CHARM
If you have been provided with additional configuration files by Vision4ce you can select which
one is loaded by the CHARM software.
Select the required configuration file and press the submit / “Set config” button. If the CHARM has
secondary user config files you can also select these. The selected files will be used next time the
CHARM is rebooted. There is a reboot button on the home page.
2. VIDEOSTREAMS THROUGH CHARM 10CE
Other manuals for MK Series
1
This manual suits for next models
1
Table of contents
Other Evve Long Range Digital Camera manuals
