evertz exponent 500DA-AESU User manual
Frame Manual
500DA-AESU Unbalanced AES Audio Distribution Amplifier
Revision 1.1
TABLE OF CONTENTS
1. OVERVIEW.......................................................................................................................................... 1
2. INSTALLATION................................................................................................................................... 2
3. SPECIFICATIONS............................................................................................................................... 3
3.1. AES AUDIO INPUTS .................................................................................................................. 3
3.2. AES AUDIO OUTUTS ................................................................................................................ 3
3.3. ELECTRICAL ............................................................................................................................. 3
3.4. PHYSICAL.................................................................................................................................. 3
4. STATUS LEDS .................................................................................................................................... 3
5. JUMPERS AND USER ADJUSTMENTS............................................................................................ 4
5.1. INPUT TERMINATION JUMPER ............................................................................................... 5
5.2. SELECTING WHETHER LOCAL FAULTS WILL BE MONITORED
BY THE GLOBAL FRAME STATUS.......................................................................................... 5
Figures
Figure 1: 500DA-AESU Block Diagram.................................................................................................................1
Figure 2: 500DA-AESU Rear Panel Overlay.........................................................................................................2
Figure 3: LED and Jumper Locations....................................................................................................................4
Frame Manual
500DA-AESU Unbalanced AES Audio Distribution Amplifier
Revision 1.1
REVISION HISTORY
REVISION DESCRIPTION DATE
1.0 Original Version Oct 02
1.1 Updated Block Diagram, LED and Jumper information Mar 03
Information contained in this manual is believed to be accurate and reliable. However, Evertz assumes no responsibility for the use thereof nor for
the rights of third parties, which may be effected in any way by the use thereof. Any representations in this document concerning performance of
Evertz products are for informational use only and are not warranties of future performance, either express or implied. The only warranty offered by
Evertz in relation to this product is the Evertz standard limited warranty, stated in the sales contract or order confirmation form.
Although every attempt has been made to accurately describe the features, installation and operation of this product in this manual, no warranty is
granted nor liability assumed in relation to any errors or omissions unless specifically undertaken in the Evertz sales contract or order confirmation.
Information contained in this manual is periodically updated and changes will be incorporated into subsequent editions. If you encounter an error,
please notify Evertz Customer Service department. Evertz reserves the right, without notice or liability, to make changes in equipment design or
specifications.
Frame Manual
500DA-AESU Unbalanced AES Audio Distribution Amplifier
Revision 1.1 500DA-AESU-1
1. OVERVIEW
The 500DA-AESU provides an economical method of distribution for your AES digital audio signals. The
DA’s feature one auto-equalized input with nine re-clocked outputs.
The 500DA-AESU is housed in the 500FR Frame that will hold up to 16 modules.
Features:
•Supports SMPTE 276M standard for AES audio on 75 Ωcoax
•9 reclocked outputs provides jitter reduction
•Automatic equalization provides extended cable length capabilities
•High impedance or 75 ohm termination on input (jumper selectable)
•Card edge indicators for AES present, reclocker rate, and AES validity bit
•Tally output of input error conditions
AES Input
(SMPTE 276M)
AES Outputs
(SMPTE 276M)
Input
Coupling
Reclocker Rate
Equalizer AES
Reclocker
Module
Status
Control
Indicators
AES
Present
48 kHz 44 kHz 32 kHz
75
Ω
AES
Valid
Figure 1: 500DA-AESU Block Diagram
Frame Manual
500DA-AESU Unbalanced AES Audio Distribution Amplifier
500DA-AESU-2 Revision 1.1
2. INSTALLATION
The 500DA-AESU comes with a companion rear panel overlay that can be placed over the rear panel
BNC connectors to identify their function. For information on inserting the module into the frame see the
500FR chapter section 3.
Figure 2: 500DA-AESU Rear Panel Overlay
IN Input BNC connector for unbalanced AES audio signals compatible with the SMPTE 276M
standard.
OUT 1 to 9 There are nine BNC connectors with reclocked unbalanced AES, compatible with the
SMPTE 276M.
Frame Manual
500DA-AESU Unbalanced AES Audio Distribution Amplifier
Revision 1.1 500DA-AESU-3
3. SPECIFICATIONS
3.1. AES AUDIO INPUTS
Number of Inputs: 1
Standard: SMPTE 276M, single ended AES
Connectors: BNC per IEC 169-8
Coupling: Transformer
Signal Level: 1V p-p ±0.1V
Equalization: Automatic to 1500m @48KHz with Belden 1694A or equivalent cable
Impedance: 75 Ohms
Return Loss: >25 dB 100 kHz to 6 MHz
Sampling Rate: 32 kHz, 44.1 kHz, 48 kHz and 96 kHz
3.2. AES AUDIO OUTUTS
Number of Outputs: 9 reclocked
Standard: SMPTE 276M, single ended AES
Connectors: BNC per IEC 169-8
Signal Level: 1V p-p ±0.1V
Impedance: 75 Ohms unbalanced
Return Loss: >25 dB 100 kHz to 6 MHz
3.3. ELECTRICAL
Voltage: + 12VDC
Power: 5 Watts.
3.4. PHYSICAL
Number of slots: 1
4. STATUS LEDS
The 500DA-AESU has seven LED Status indicators on the front card edge to show operational status of
the card at a glance. Figure 3 shows the location of the LEDs.
Two large LEDs on the front of the board indicate the general health of the module
LOCAL FAULT: This Red LED indicates poor module health and will be On during the absence of a
valid input signal, or if a local input power fault exists (i.e.: a blown fuse). The
LOCAL FAULT indication can also be reported to the frame through the FRAME
STATUS jumper.
MODULE OK: This Green LED indicates good module health. It will be On when a valid input
signal is present, and the board power is good.
Frame Manual
500DA-AESU Unbalanced AES Audio Distribution Amplifier
500DA-AESU-4 Revision 1.1
There are five small LEDs that indicate the status of the input AES audio.
AES PRESENT: This LED will be On when there is an AES carrier present at the input to the module.
48 kHz: The reclocker is currently locked to 48 kHz
44 kHz: The reclocker is currently locked to 44.1 kHz
32 kHz: The reclocker is currently locked to 32 kHz
AES VBIT This LED indicates the status of the AES validity bit. When the LED is Off it
indicates that the AES sample data is suitable for conversion to an analog audio
signal. When the LED is On it indicates that the AES sample data is carrying data
such as Dolby E and is not suitable for conversion to an analog audio signal.
5. JUMPERS AND USER ADJUSTMENTS
+12V GND
MODULE STATUS
(A)500DA-AES-UB
AES PRESENT
48 KHZ
44 KHZ
32 KHZ
AES VBIT
J1
FRAME STATUS
ON
OFF
J5
TERMINATION
HI-ZTERM
Figure 3: LED and Jumper Locations
Frame Manual
500DA-AESU Unbalanced AES Audio Distribution Amplifier
Revision 1.1 500DA-AESU-5
5.1. INPUT TERMINATION JUMPER
The TERMINATION jumper J5, located at the rear of the module determines whether the input signal will
be terminated or not.
TERMINATION When set in the "TERM" position, (default) the input impedance is set to 75 Ohms.
Use this position when the cable stops at this card. It will provide the proper
impedance to eliminate electrical reflections.
If set to "UNTERM", the input will be high impedance. Use this position when the
signal does NOT stop at this card. Install a "T" connector on the INPUT BNC to
"loop" the signal through this card.
!WARNING: Make sure that the final destination of the signal is terminated.
Otherwise, reflections will occur affecting the signal throughout the cable.
5.2. SELECTING WHETHER LOCAL FAULTS WILL BE MONITORED
BY THE GLOBAL FRAME STATUS
The FRAME STATUS jumper J1, located at the front of the module determines whether local faults (as
shown by the Local Fault indicator) will be connected to the 500FR frame's global status bus.
FRAME STATUS: To monitor faults on this module with the frame status indicators (on the power
supply’s FRAME STATUS LED's and on the Frame's Fault Tally output) install this
jumper in the On position.
When this jumper is installed in the Off position local faults on this module will not
be monitored.
Frame Manual
500DA-AESU Unbalanced AES Audio Distribution Amplifier
500DA-AESU-6 Revision 1.1
This page left intentionally blank
Table of contents
Other evertz Amplifier manuals
evertz
evertz exponent 500ADA User manual
evertz
evertz 7700ADA6-EQ-L User manual
evertz
evertz exponent 500ADA-W User manual
evertz
evertz 500DA2Q-AESU User manual
evertz
evertz 7700 MultiFrame User manual
evertz
evertz exponent 500ADA-AUD User manual
evertz
evertz 500DA2Q-3G User manual
evertz
evertz 7700 Series User manual
evertz
evertz exponent 500DA-AESU-L User manual
evertz
evertz 9000EDFA-D-AGC User manual
evertz
evertz 7700 Series User manual
evertz
evertz 500DA User manual
evertz
evertz 7700 Series User manual
evertz
evertz 7700 Series User manual
evertz
evertz 7700 Series User manual
evertz
evertz 7700ADA-EQ User manual
evertz
evertz 7815VPDA Series User manual
evertz
evertz 500DA-AESB User manual
evertz
evertz 7700ADA7-EQ MultiFrame User manual
evertz
evertz exponent 500DA2Q-HD User manual
