EVA Logik ZW31 User manual

Model: ZW31

Power: 120VAC, 60Hz

Frequency: 908.42 MHz

Maximum Load: 150W LED, 500W incandescent

(300W with both sides of heat sink tabs oﬀ)

Minimum Load: 5W for LED bulbs

Range: Up to 100 feet line of sight Operating

Temperature Range: 32-104° F (0-40° C)

For indoor use.

Speciﬁcations subject to change without notice

due to continuing product improvement

Approval: Z-Wave Plus Certiﬁed

switch x1

Z-WAVE INTEROPERABILITY

This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers and/or other applica-

tions. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase the reliability of the network.

This Device supports Lifeline (association group 1) supporting 1 node for lifeline communication.

Group 1 must be assigned the Node ID of the primary controller where unsolicited notifications will be sent. The Z-Wave controller should set this

association automatically aer inclusion.

Lifeline association only supports the “Device Reset Locally” function. Refer to the instructions of your controller for any available details on how this

can be set.

wallplate x1 wiring x1 screws x2

Part 1. Introduction

Contents

A quick note before we give out the wiring schematics. Please do not try installing this device if you are unsure of how electrical circuits operate

within your home. As exciting as it is to have a smart switch installed, it can be dangerous and even life-threatening if you do not install this

correctly. Please consult a qualiﬁed electrician if necessary. With that said, here are a few other warnings we’d like to point out for your safety:

A Few Quick Reminders

Note before installation

1) The Z-Wave In-wall Smart Switch must not exceed 150W LED, 500W incandescent.

2) The switch box required: 1-gang U.S. wall box. 3½ in deep recommended, 2¼ in deep minimum.（The switch is designed only for use

with permanently installed fixtures.）

3) Work with regular 3-way on/oﬀ for 2 locations control. It can only be connected with regular 3-way on/oﬀ switch, don't use a smart

switch or a dimmer switch! Couldn't work with an add-on switch!

4) The colors of your wires may not match the ones in our diagrams so please make sure you've identified all wires correctly based on

their source, not color only.

5) Please check your original 3-way wiring circuit in your home before installation, and then follow the wiring diagram option 1 or 2 in

the manual.

6) Install the smart switch in the switch box which directly connects to the power Line and Neutral.

7) This switch requires a Neutral for installation, or the installation will not succeed.

8) Not recommended for fan.

Convention Description Convention Description

• Locally button function

• LED indicator status setting

• Auto Turn-On/Oﬀ timer

• Association setting parameter

• Restore state aer power failure

• Light oﬀ state setting

• Button function setting

• Multilevel minimum value can be set

• Association group

• Generic device class

• Command classes

Function description

• LED indicator/ Button function

• Adding / reset the device ( Factory setting)

• Min & Max Brightness Value Setting

• Wiring instructions

• Single pole and 3-way wiring diagram

• Product introduction

• Installation steps

Part 1.

Introduction

Part 2.

Wiring Diagram

Part 3.

Manual Control

• Solutions to some common problems

Part 4.

Troubleshooting

CHANGING THE COLOR OF THE PADDLE(OPTIONAL)

This step is optional. Before you start you may want to change the color of the

paddle to match your wallplate or decor.

1. Push side tabs in on one side and then the other to release paddle. Li the

cover up and oﬀ.

2. Simply put the new paddle onto the switch by side tabs and snap securely

into place.Once this step has been completed please proceed to part 2 wiring.

If you have any questions, please contact us at

[email protected]

HOW TO INSTALL THE WIRES

STRIP WIRE AT 3/8-1/2”

1. Unscrew: carefully turn the screw counterclockwise to leave enough space for

the wire to be inserted. Do not unscrew the screws completely.

2. Press down: Once loosened, use your finger so it catches the thread.

3. Insert the wire: make sure the wire is completely straight, then insert it into the

terminal while holding down the screw. Do not wrap the wire around the screw!

4. Tighten: Turn the screw clockwise to tighten the wire. Make sure the

wires are locked!

Note: There are 2 holes for each terminal can be used in the

connection.You can use a jump wire or the second hole at the

terminal to connect.

Line (hot) — black (connected to power)

Neutral — white

Load — black (connected to lighting)

Traveler — red/other

(only in 3-way installations)

Line

Load

Ground

Traveler

Neutral

1. 4.

Basic Operation

The connected light can be turned ON/OFF in two ways:

1. Manually from the front panel of the In-wall Switch

2. Remotely with a Z-Wave Controller

Manual Control

The Front Panel Paddle Switch allows the user to:

Turn ON/OFF the connected fixture

Single-pole wiring

3-Way switch option 1

1) Neutral required. If the box do not have a Neutral,

please stop! Connect the white wire to neutral

terminal(use a white jump wire form the package or

the second hole at the terminal to connect.)

2) Insert the Line wire to Line terminal and Load wire to

Load terminal. LOAD and LINE Can’t be swapped,

please make sure to identify them correctly!

IMPORTANT

1. Tool: Please prepare a flat head screwdriver.

2. Turn power OFF at circuit breaker or fuse box.

3. Remove wallplate.

4. Remove the switch mounting screws.

5. Disconnect the wires and label them aer remove

the old switch.(Please use our sticker)

6. Carefully remove the switch from the switch box. (DO

NOT disconnect the wires.)

7. There are up to five screw terminals on the smart

switch, these are marked (Please check <HOW TO

INSTALL THE WIRES>)

8. Fix the wallplate with screws aer wiring succeed.

(Please use our screws.)

9.The Ground was excluded from the diagram to

simplify the illustration. Please Make sure all ground

wires are connected to all switches respectively.

Line Load GroundNeutral Traveler(Just for 3-way switch)

1) Neutral required. If the switch box do

not have a Neutral, please stop!

Connect the white wire to neutral

terminal (use a white jump wire form

the package or the second hole at the

terminal to connect.)

2) Insert the Line wire to Line terminal

and Load wire to Load terminal.

LOAD and LINE Can’t be swapped,

please make sure to identify them

correctly!

3) Install the smart switch in the switch

box which directly connects to the

power Line, Load and Neutral.

4) Only work with regular 3-way on/oﬀ

for 2 locations control. It can only be

connected with regular 3-way on/oﬀ

switch, don't use a smart switch or a

dimmer switch! Couldn't work with

an add-on switch!

Power

regular 1 regular 2

common

common Line

Load

Neutral

Traveler

From source

(3-way switch)

IMPORTANT

Neutral

Line

Neutral

Line

Smart

Switch

OUT TO LIGHT

regular

Line

Load Neutral

From source

Ground

Load

Neutral

Line

Traveler

Line

Load

Neutral

From source

Neutral

OUT TO LIGHT

Ground

Load

Neutral

Line

Traveler

regular

common

None-connection

Line

Load

Neutral

Traveler

From source

( Line/Hot Neutral and Light/Load)

(3-way switch)

Box 1 Don’t change this

regular 3-way on/oﬀ switch

Box 2

OUT TO LIGHT

3-Way Z-Wave Smart Dimmer Switch

• ZW31 •

Part 5.

Parameter Settings

Part 2. Wiring Diagram

Air-Gap Switch:

The "air gap switch" will cut power to the device if it's pulled up. It's located

right below the main switch itself, oen next to the LED. Pull up for Bulb

replacement, push down for normal use.

Neutral

Line Neutral

Line

Smart

Switch

common

common common

For more detials, please refer to the manual parts.

If you have any questions during installation,

Please contact us [email protected]

OTHER WARNINGS

Risk of Fire

Risk of Electrical Shock

Risk of Burns

MEDICAL EQUIPMENT

FCC / IC

This device complies with part 15 of the FCC and Industry Canada

license-exempt RSS standard(s). Operation is subject to the following two

conditions:

(1) this device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause

undesired operation.

NOTE: This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions may cause harmful interference to radio

communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by

turning the equipment oﬀ and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

— Reorient or relocate the receiving antenna.

— Increase the separation between the equipment and receiver.

— Connect the equipment into an outlet on a circuit diﬀerent from that to

which the receiver is connected.

— Consult the dealer or an experienced radio/TV technician for help

Important note: To comply with the FCC RF exposure compliance

requirements, no change to the antenna or the device is permitted. Any

change to the antenna or the device could result in the device exceeding

the RF exposure requirements and void user’s authority to operate the

device.

FCC NOTE: The manufacturer is not responsible for any radio or TV

interference caused by unauthorized modiﬁcations to this equipment. Such

modiﬁcations could void the user’s authority to operate the equipment.

CAUTION - PLEASE READ!

This device (ZW31) is intended for installation in accordance with the

National Electric Code and local regulations in the United States, or the

Canadian Electrical Code and local regulations in Canada. If you are

unsure or uncomfortable about performing this installation consult a

qualiﬁed electrician.

CONTROLLING APPLIANCES

Please exercise EXTREME CAUTION when using Z-Wave devices to

control appliances. Reason being is because the appliance you want to

control may be in a separate room and if unintentional behavior occurs

(such as a device turning on or oﬀ - either intentionally via schedules, or

unintentionally via network error) this event may lead to a hazardous

condition. For these reasons, please note the following suggestions:

1) Do not include Z-Wave devices in Groups or Scenes if they control

appliances.

2) Do not use Z-Wave devices to control electric heaters or any other

appliances which may present a hazardous condition due to unattend-

ed, unintentional, or automatic power control

WARNING - SHOCK HAZARD

TURN OFF THE POWER to the circuit for the switch and lighting ﬁxture at

the service panel (circuit breaker) prior to installation.

ALL WIRING CONNECTIONS MUST BE MADE WITH THE POWER OFF to

avoid personal injury and/or damage to the switch.

Please DO NOT use this switch to control Medical or Life Support

equipment. Z-Wave devices should never be used to control the On/Oﬀ

status of Medical and/or Life Support equipment.

2020.6.22 V4.0

3-Way switch option 2 Power

1) Neutral required. If the switch box do

not have a Neutral, please stop!

Connect the white wire to neutral

terminal (use a white jump wire form

the package or the second hole at the

terminal to connect.)

2) Insert the Line wire to Line terminal

and Load wire to Load terminal.

LOAD and LINE Can’t be swapped,

please make sure to identify them

correctly!

3) Install the smart switch in the switch

box which directly connects to the

power Line and Neutral.

4) Only work with regular 3-way on/oﬀ

for 2 locations control. It can only be

connected with regular 3-way on/oﬀ

switch, don't use a smart switch or a

dimmer switch! Couldn't work with

an add-on switch!

(Line/Hot and Neutral)

Box 1 (Load)

Don’t replace this

regular 3-way on/oﬀ switch

Box 2

IMPORTANT

Neutral

regular 1

regular 2

common

Load

Line

Traveler

common

From source

OUT TO LIGHT

Ground

Load

Neutral

Line

Traveler

Neutral

regular

Load

Line

Traveler

common

From source

OUT TO LIGHT

To exclude and reset the device

Works with Alexa & Google Assistant

To return your switch to factory defaults

Adding your device to a Z-Wave network

Make your controller/hub into the "inclusion"

mode, triple press the Up/Down push button

quickly to include it in the network.

Make your controller/hub into the "exclusion"

mode, triple press the Up/Down push button

quickly to exclude it from the network.

1. Tap-tap and hold the upper paddle for at

least 10 seconds.

Note: This should only be used in the event

your network’s primary controller is missing

or otherwise inoperable.

Scene:

Scene 1: Tap-Down-2

Scene 2: Tap-Up-2 It must be connected to a supported hub in order to interact with the

Amazon Alexa / Google Home services.

1: Press the button 5 times (up/down) quickly, the blue indicator light flashes slowly, enter the setting “Min brightness” mode, and

the load lamp automatically adjusts to the min brightness.

2: Press the up or down button to adjust the brightness of the bulb, select the appropriate brightness to set the min brightness.

3: Quick Press the button 5 times (up/down) to confirm it (the min brightness setting is completed). It will be entered into the “Max

Brightness” setting automatically, the bulb will adjust to the max brightness.

4: Press the up or down button to adjust the brightness of the bulb, and select the appropriate brightness to set the max bright-

ness.

5: Press the button 5 times (up/down) to confirm.

6: Aerconfirmation,the brightness ofthe bulbwillautomaticallybe adjustedfromthesetminbrightnesstothe maxbrightness,

thenfromthemaxbrightnesstotheminbrightness,finallystaysatthesetminbrightness. The blue indicator light stops

flashing.

7: Min / Max brightness level settings are completed.

Remark: If the setting is not confirmed at Step 3/Step 5, the setting mode will be exited aer 10S, and the adjusted value will not

be saved.

Min / Max brightness level setting

Our Products warrants this product to be free from manufacturing defects for a period of one year from the original date of consumer purchase.

This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other

products that may be used with this product. This warranty is in lieu of all other warranties, expressed or implied. Some states do not allow

limitations on how long an implied warranty lasts or permit the exclusion or limitation of incidental or consequential damage, so the above

limitations may not apply to you. This warranty gives you specific rights, and you may also have other rights which vary from state to state.

WARRANTY

If you have any questions, please contact us at

[email protected]

LED Status(Blue) Switch

ON ( Default ) power oﬀ ( Default )

power on ( Default )

configuration succeed

inclusion /exclusion

OFF ( Default )

flash two times

flash quickly

flash slowly

Operation

factory default

change LED status

parameter change

press down

press up

tap-tap and hold 10 seconds

press 6x quickly

press 3x quickly (see below)

press 5x quickly

press 2x quickly

press 7x quickly

press 8x quickly

change locally button function

restores state aer power failure

hold dimmer up or dimmer down

send scene 1 / scene 2

Min / Max brightness level setting

Part 3. Manual Control

Part 5.Parameter Settings

Possible Problem Possible Cause Solution

1. The connected LED is flashed/too bright when

set it to the Minimum brightness level.

2. Couldn't pair with hub/your hub cannot

recognize the device.

3. The device couldn't trun lights on/oﬀ manually.

4. The smart switch is working and the 3-way

switch does not.

LED brightness minimum setting is incorrect.

The device needs to be resetted before pairing.

Wiring errore

Please set the minimum brightness level

according to the manual.

Please reset the device according to the manual.

Please check the wiring diagram on the manual.

3-way Wiring error Please check the wiring diagram on the manual.

Part 4. Troubleshooting

Generic Device Class:

0x11- GENERIC_TYPE SWITCH_MULTILEVEL

Specific Device Class:

0x01-SPECIFIC_TYPE POWER_SWITCH_MULTILEVEL

Command Classes:

0x5E - COMMAND_CLASS_ZWAVEPLUS_INFO

0x26 - COMMAND_CLASS_SWITCH_MULTILEVEL

0x85 - COMMAND_CLASS_ASSOCIATION

0x8E - COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION

0x59 - COMMAND_CLASS_ASSOCIATION_GRP_INFO

0x55 - COMMAND_CLASS_TRANSPORT_SERVICE

0x86 - COMMAND_CLASS_VERSION

0x72 - COMMAND_CLASS_MANUFACTURER_SPECIFIC

0x5A - COMMAND_CLASS_DEVICE_RESET_LOCALLY

0x73 - COMMAND_CLASS_POWERLEVEL

0x70 - COMMAND_CLASS_CONFIGURATION

0x5B- COMMAND_CLASS_CENTRAL_SCENE

0x9F - COMMAND_CLASS_SECURITY_2

0x6C - COMMAND_CLASS_SUPERVISION

0x7A - COMMAND_CLASS_FIRMWARE_UPDATE_MD

Parameter Available settings Operation

The indicator will flashes 2 times aer each parameter set successfully.

Parameter 1:

Button Function Setting

This parameter can access you to set

the up button to turn the light on/oﬀ.

Please note: the switching of each value

is in order, a quick press on button 7

times will switch once. eg: Switching

from value 0 to value 2 needs 2 switching.

Size=1

Value=0 (Default)The up button turn the light on and

down button turn lights oﬀ.

Value=1 -----------The up button turn the light oﬀ and down

button turn lights on.

Value=2 -----------The up/down button both can changes

the state of the light.

Quick press the switch button 7 times

Parameter 2:

LED Indicator Status Setting

This parameter can access you to

choose the led indicator to be on

when the switch(light) is on/oﬀ, or

LED indicator remains on/oﬀ all times.

Size=1

Value=0 (default) LED is On when the switch(light) Oﬀ

and LED is Oﬀ when the switch (light) On.

Value=1 -----------LED is On when switch(light) On and

LED is Oﬀ when the switch(light) Oﬀ.

Value=2 -----------LED is always Oﬀ.

Value=3 -----------LED is always On.

Please note: the switching of each value

is in order, a quick press on button 6

times will switch once. eg: Switching

from value 0 to value 3 needs 3 switching.

Quick press the switch button 6 times

Parameter 8:

Restores State aer Power Failure

This parameter can access you to set the

switch to be on/oﬀ aer power failure.

Size=1

Value=1-----------The switch is oﬀ regardless of the state

prior to power failure.

Value=2(default) memory state before power failure

This switch will be return to state prior to the power failure

aer power is restored.

Please note: the switching of each value

is in order, a quick press on button 8

times will switch once. eg: Switching

from value 0 to value 2 needs 2 switching.

Quick press the switch button 8 times

Parameter 4:

Auto Turn-Oﬀ Timer.

This parameter can access you to set a

timer to make the switch turn oﬀ automati-

cally aer the switch turned on.The

numberentered as value corresponds to

number of minutes.

Size=4

Values: 0 – 65535 (minutes);

Value=0 (minutes) – default setting Set up on the hub

Parameter 6:

Auto Turn-On Timer.

This parameter can access you to set a

timer to make the switch turn on automati-

cally aer the switch turned oﬀ.The

numberentered as value corresponds to

number of minutes.

Size=4

Values: 0 – 65535 (minutes);

Value=0 (minutes) – default setting

Set up on the hub

direct control of other devices

within the Z-Wave system network.

Association Group:

Linking devices: Group 1 supports 1 node ID,

Group 2 Supports maximum of 5 node ID’s

Association group_1:Z-Wave Plus Lifeline

Association Group 2:Send Basic Set ON / Oﬀ

Set up on the hub

Parameter=7

Size=1

Default = 1

Value=00 – none

Value=01 - local

Value=02 - 3way

Value=03 - 3way & local

Value=04 - z-wave hub

Value= Value=05 - z-wave hub & local

Value=06 - z-wave hub & 3-way

Value=07 - z-wave hub & local & 3way

Value=08 - timer

Value=09 - timer & local

Value=10 - timer & 3-way

Value=11 - timer & 3-way & local

Value=12 - timer & z-wave hub

Value=13 - timer & z-wave hub & local

Value=14 - timer & z-wave hub & 3-way

Set up on the hub

Association Setting

Size=1，

Value=0 disable

Value=1

Value=99

Default = 10

Parameter 11:

Multilevel minimum value can be set

Quick press the switch button 5 times

This parameter can access you to set

Min / Max brightness level setting

Neutral

Line

Smart

Switch

Neutral

Line

common common

common

Other EVA Logik Dimmer manuals

EVA Logik

EVA Logik ZW313 User manual

Popular Dimmer manuals by other brands

ZooZ

ZooZ ZEN54 LR user manual

Lex

Lex 6KW user guide

DIODE LED

DIODE LED TOUCHDIAL Mini installation guide

Viessmann

Viessmann 5590 Operation manual

American DJ

American DJ DP-8A instruction manual

Teleco

Teleco TVSTICK868RGB29 manual

INSTEON

INSTEON LampLinc 2457D2 quick start guide

LEGRAND

LEGRAND WattStopper RH703PTU installation instructions

ADB

ADB EURODIM TWIN TECH user manual

Sinope

Sinope DM2550ZB-C4 installation guide

SkyLink

SkyLink SK7 installation instructions

Makel

Makel RC operating instructions

Lightronics

Lightronics XC-62 owner's manual

Triton Blue

Triton Blue DM-1225 user manual

ETC

ETC ES750 Programming guide

NA OMEGA + user manual

GE ZB3001 manual

LSC

LSC DP-1210 user manual