Eurotech EUR-FSGE60 User manual

Model : EUR-FSGE60

Dear Valued Customer

Thank you and congratulations on purchasing our new Eurotech appliance.

Please read through your manual thoroughly before using your new Eurotech appliance it will

provide you with an understanding of

the functions,

features and most importantly information needed to

ensure its safe installation.

Please take special note of all the technical information and installation instructions. It

essential that, only a qualified technician installs this appliance to ensure the safety and

reliability of the appliance.

Please note failure to use appropriate qualified installer and to could result in your warranty being invalid.

If you require any assistance please check with Eurotech Design Limited before installation is carried

out.

We hope you enjoy your new appliance. To view our full range of products visit

www.eurotechdesign.co.nz

IMPORTANT NOTE

New Zealand law dictates that this appliance must be installed by an authorized

installer.The installation of this appliance must comply with all the appropriate New

Zealand standards and Regulatory requirements with particular reference to New

Zealand Electrical and / or Gas installation Standards.

Any attempt to install this or any other Eurotech Design products without authorized

installation could result in damage to the product and possible health hazards. As well

as result in all associated warranties being null and void.

Index

pag.3-4

Instructions for installation:

Dimensions and installation features pag. 5

Electrical connection pag. 6

Ventilation and gas connection pag. 6

Adaptation to different types of gas pag. 7

Setting the minimum flame pag. 7

Burner and injector characteristic table pag. 8

Instructions for use

Description of the main parts of the appliance pag. 8

Ignition and operation of the burners pag. 9

Advice on the use of gas burners pag. 9

Oven function pag. 10

Electronic programmer pag. 11

Maintenance and cleaning pag. 14

CAUTIONS

pag. 12Instructions for cooking

Very important: keep this instruction booklet with the appliance for handy references

This appliance is designed for use in private home. Please be aware that the front accessory could be not

to touch.

lIf a gas appliance is used for a long time it may require extra ventilation (opening a window or increase

the volume of exhaust).

lNever line the oven with aluminium sheets as the slots preset for keeping fast the thermic exchange may

clog, thus damaging the enamel.

lBe careful not to place saucepans with unstable or deformed bottoms on the burners to avoid overturning

or spilling .

lThis appliance is not intended for use by young children .

l Don't touch the heating elements inside the oven.

lWhen the grill is on all the accessible elements are hot, hence, keep children away from these elements.

l This appliance shall be installed only by authorised persons and in accordance with the manufacturer's

Installation instructions, local gas fitting regulations, municipal building codes electrical wiring

regulations,and local water supply regulations.

l Before switching the appliance on check that it is correctly regulated for the type of gas available (see

relevant section).

Do not use jet of steam for cleaning.

l Before maintenance or cleaning, disconnect the appliance from the mains and wait for it to cool down.

lWhen the burners are lit check that the flame is always regular. Before removing the saucepans turn the

burners off.

lServicing should be carried out only by authorised personnel.

lThe use of a gas appliance produces heat and humidity in the room . Make sure that the room is well

ventilated, keeping the natural ventilation outlets open or installing a ventilation hood with rain duct.

lIf the mains of a burner is turned off accidentally, turn off the control knob. Only light the oven again

after waiting at least a Minute.

Before using the oven, we suggest to:

lRemove all the special film covering the oven door glass (when provided)

lHeat the empty oven at max. Temperature for 45 minutes (to remove unpleasant smell and smoke caused

by working residues and by the thermal insulation)

lCarefully clean inside the oven with soapy water and rinse it .

lFor any repairs always contact an authorised Eurotech Design Customer Service Centre and ask for original

spare parts. Repairs by untrained people can lead to damage.

lKeep packaging out of reach of children at all times.

lAlways use oven gloves to remove and replace food in the oven. Ensure that you support the grill pan

when removing it from the oven.

lDon't let children sit down or play with the oven door.Do not use the drop down door as a stool to reach

cabinets above.

lDO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS IN OPERATION.

l DO NOT STORE OR USE FLAMMABLE LIQUIDS OR ITEMS IN THE VICINITY OF THIS

APPLIANCE.

lWHERE THIS APPLIANCE IS INSTALLED IN MARINE CRAFT OR IN CARAVANS, IT SHALL NOT

BE USED AS A SPACE HEATER .

lDo not remove the plup by pulling the cable.

WARNING: In order to prevent tipping of the appliance, this stabilizing means must be installed. Refer to the

instructions for installation.During use the appliance becomes hot. Care should be taken to avoid touching

heating elements inside the oven.

WARNING: Accessible parts may become hot during use. Young children should be kept away.

Do not use harsh abrasive cleaners or sharp metal scrapers to clean the oven door glass since they can scratch

the surface, which may result in shattering of the glass. This appliance is not intended for use by persons

(including children) with reduced physical,sensory or mental capabilities, or lack of experience and

Important Safety Information

knowledge, unless they have been given supervision or instruction concerning use of the appliance by a

person responsible for their safety.Children should be supervised to ensure that they do not play with the

appliance.

lIf the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly

qualified persons in order to avoid a hazard. In the event of burner flames being accidentally

extinguished,turn off the burner control and do not attempt to re-ignite the burner for at least 1 min.

lNote:These instructions are only valid if the country symbol appears on the appliance. If the symbol does

not appear on the appliance, it is necessary to refer to the technical instructions which will provide the

necessary instructions concerning modification of the appliance to the conditions of use of the country Gas

appliance

Before using the appliance: IMPORTANT NOTICE

Read the instructions thoroughly

New Zealand law dictates that this appliance must be installed by an authorized

installer. The installation of this appliance must comply with all the appropriate New

Zealand standards and Regulatory requirements with particular reference to New

Zealand Electrical and / or Gas installation Standards.

Any attempt to install this or any other Eurotech Design products without authorized

installation could result in damage to the product and possible health hazards. As well

as result in all associated warranties being null and void.

Eurotech Design Limited

604 Rosebank Road

Avondale, Auckland

Instructions for Installation

DIMENSIONS AND INSTALLATION FEATURES

Warning:

a) Prior to installation, ensure that the local distribution conditions (nature of the gas and gas pressure) and

the adjustment of the appliance are compatible;

b)The adjustment conditions for this appliance are stated on data plate;

c) This appliance is not connected to a combustion products evacuation device. It shall be installed and

connected in accordance with current installation regulations. Particular attention shall be given to the

relevant requirements regarding ventilation.

The cooker is supplied with an anti-tilting chain to prevent the appliance

from tilting forward and accidental damage to the gas pipe. Take the

expansion with hook and make an adequate hole in the wall behind, at the

same height as the chain fixing area. Insert the plug into the hole and then

screw in the hook until it is firmly fixed to the wall. Fix the chain to the

hook. Adjust to level of the cooker inserting the feet provided.

For a situation where the appliance is between two cupboards and the anti tilt chain cannot be fitted we

suggest securing by screwing through the both sides of the cupboards into the sides of the cooker. The screws

should be

fitted as follows. Position the oven between the cupboards in it's final position, then mark the location of the

pilot hole inside the cupboard. Refer to the diagram below for the location of the pilot hole. Use 3.5mm

diameter drill bit to drill the pilot hole through the cupboard and both sides of the cooker. Before drilling,

check your measurements to ensure the pilot holes are located within the range specified in the diagram. A

drilled hole in the

side of the cooker which is outside the range specified may void the warrantee. Inspect cupboards thoroughly

before drilling to avoid damage to electrical wires or gas lines. Fix two 12 gauge x 40mm long self tapping

screws through the pilot holes inside both cupboards and into the side of the cooker.

Note! Screw length is based on cupboard thickness of 20mm, gap between cupboard and oven of 10mm.

Screw length could vary depending on cupboard material thickness and gap between oven and cupboards.

Note! The screws must be accessible for removal if the cooker requires service. Cupboards must not be built

over these screws.

Equipment type: free standing (class 1)

Insulation class: class 1

THE MANUFACTURER DECLINES ANY AND ALL RESPONSIBILITIES FOR DAMAGES TO THINGS

OR INJURIES TO PERSONS OR ANIMALS DERIVING FROM INCORRECT INSTALLATION OR USE OF THE

EQUIPMENT.

Nominal volume of the oven

56 lt

ELECTRICAL CONNECTION

The appliance is fitted with an Australian approved 15 Amp flexible cord and plug which must be connected

to a correctly earthed socket outlet. The manufacturer is not liable for any direct or indirect damage caused by

faulty installation or connection. It is therefore necessary that all installation and connection operations are

carried out by qualified personnel complying with the local and general regulations in force.

The wire section on the cable must not be less

Than1.5mm (3×1.5cable).Use only the special

cables available at our service centers.

CONNECTION OF THE FEEDING CABLE TO THE MAINS

Connect the feeding cable to a plug suitable for the load indicated on the rating plate of the product. In case of

a direct connection to the mains (cable without plug), it is necessary to insert a suitable omnipolar switch

before the appliance, with minimum opening between contacts of 3 mm (the grounding wire should not be

interrupted by the switch).

Before connecting to the mains, make sure that:

The electrical counter, the safety valve, the feeding line and the socket are ade

quate towithstand the maximum load required(see rating plate).

The supply system is regularly grounded, according to the regulations in force.

The socket or the omnipolar switch can easily be reached after the installation

of the oven.

After carrying out the connection to the mains, check that the supplying cable

does not come into contact with parts subject to heating.

Never use reductions, shunts, adaptors which can cause overheating or burning.

The manufacturer is not liable for any direct or indirect damage caused by faulty installation or connection. It

is therefore necessary that all installation and connection operations are carried out by qualified personnel

complying with the local and general regulations in force.

Electrical features

Oven light 25W

Upper heating element 1950W

Bottom heating element 1800W

Grill heating element 2250W

Circular heating element 1800W

Ventilator motor 30W

Cooling fan 11W

This appliance shall be installed only by authorised persons and in accordance with the manufacturer's

installation instructions, local gas fitting regulations, municipal building codes, electrical wiring

regulations, local water supply regulations.

Ventilation

In general, the appliance should have adequate ventilation for complete combustion of gas, proper flueing

and to maintain temperature of immediate surroundings within safe limits.

Combustible Surfaces

Any adjoining wall surface situated within 200mm from the edge of any hob burner must be a suitable non-

combustible material for a height of 150mm for the entire length of the hob. Any combustible construction

above the hotplate must be at least 600mm above the top of the burner and no construction shall be within

450mm above the top of the burner. Zero clearance is permitted on side and rear adjoining surfaces below the

hob.

Gas connection

The appliance must be connected to the gas supply or the cylinder according to the specifications of the

standards and after checking that it is adjusted for the type of gas available.

The gas connection is male 1/2" BSP and is situated 55mm from the right and 560mm from the floor.

There are two ways to carry out

the connection to the main gas line:

A. The Cooker can be connected with the cuprum material . Loosen the tie-in down and connect one terminal

of the pipe with the gas elbow

B. The cooker can be connected with a Flexible Hose, which is 10mm ID, class B or D,

Spit motor 4W

It's

necessity of changing the flexible tube whenthe national conditions require it.

between 1 - 1.2m long. The hose should not be subjected to abrasion, kinking or permanent deformation and

should be able to be inspected along its entire length. Unions compatible with the hose fittings must be used

and connections tested for gas leaks.

.The fixed consumer piping outlet should be at approximately the same

height as the cooker connection point, pointing downwards and approximately 150mm to the side of the

cooker. The hose should be clear of the floor when the cooker is in the installed position. Fix one end of the

chain on the screw next to the gas inlet connection and the other end should be anchored to the floor/wall so

that the chain prevents strain on the hose connections when he cooker is pulled forward.

The appliance is factory set for Natural gas. The test point pressure should be adjusted to with the

Wok burner operating at maximum.

The appliance is set up to operate with the gas specified on the gas type label placed on the back of the

appliance.

To perform these operations the qualified installer will follow the indications given in the "Adaptation to the

various types of gas" section. For safer operation make sure that the supply pressure respects the values given

in the "Table of burner and injector characteristics".

If installing for use with gas, ensure a gas regulator suitable for a supply pressure of is part of the

gas tank supply and the test point pressure is adjusted to .

Once the appliance has been installed, make sure that the gas pipe is neither squashed or damaged by moving

parts.

Before Leaving - Check all connections for gas leaks with soap and water. DO NOT use a naked flame for

detecting leaks. Ignite all burners both individually and separately to ensure correct operation of gas valves,

burners and ignition. Turn gas taps to low flame position and observe stability of the flame for each burner

individually and separately. When satisfied with the operation of the cooker, please instruct the user on the

correct method of operation. In case the appliance fails to operate correctly after all checks have been carried

out, refer to the authorised service provider in your area.

Adaptation to different types of gas

To adapt the appliance to a gas different from that

for which it was set up (see gas type label inside

the warming compartment door) proceed as follows:

remove the grids

remove the burners caps and burner heads

with a 7 mm socket spanner unscrew and remove the injectors.

replace the injectors with those supplied corresponding to the

gas available (see burner and injector characteristics Table)

replace the various parts proceeding in reverse.

When converting from Natural Gas to ensure that theNG regulator is removed and replaced with the Test

Point Assembly. A gas regulator suitable for a supply pressure of should be part of the gas tank supply and the

test point pressure should be adjusted to

Setting the minimum flame

The flame on the small output is regulated by the factory.

When the injectors have been replaced or there are special

mains pressure conditions, it may be necessary to regulate

the minimum flame again. The operations necessary to set

the minimum flame are as following:

light the burner ;

turn the knob to the minimum position ;

take out the knob (and gasket if there is one) ;

The flexible tube shall be fitted in such a way that it cannot come into

contact with a moveable part of the housing unit (e.g. a drawer)and does not pass through any space

susceptible of becoming congested

20mbar

LPG 29mbar

29mbar

When converting from Universal LPG to Natural Gas ensure that the LPG test point is removed and replaced

with the CE Approved NG Regulator supplied in this kit. The test point pressure must be adjusted to

20mbar with the largest burner operating on maximum flame.

When converting from Natural Gas to Universal LPG ensure that the NG regulator is removed and replaced

with the Test Point Assembly supplied in this kit. An CE Approved gas regulator suitablefor a supply pressure

of 29mbar should be part of the gas tank supply and the test point pressure must be adjusted to 29mbar.

LPG

the pressure according to the data plate.

THE BURNERS REQUIRE NO REGULATION OF THE PRIMARY AIR.

ABNORMAL OPERATION

ANY OF THE FOLLOWING ARE CONSIDERED TO BE ABNORMAL OPERATION

AND MAY REQUIRE SERVICING:

l Yellow tipping of the hob burner flame.

lSooting up of cooking utensils.

lBurners not igniting properly.

lBurners failing to remain alight.

lBurners extinguished by oven door.

lGas valves, which are difficult to turn.

IN CASE THE APPLIANCE FAILS TO OPERATE CORRECTLY, CONTACT

THE AUTHORISED SERVICE PROVIDER IN YOUR AREA.

plut the knob back on and turn it quickly from the maximum position to the minimum position, checking

that the flame does not go out ;

l for burners with safety valve make sure that the regulation obtained is sufficient to maintain heating of

the thermocouple. If it is not, increase the minimum

LPG TO NG:Use a thin blade screwdriver to turn the by-pass screw located above left of the gas

valve,shaft as shown right. Turn gently the by-pass screw clockwise to the end completely then turn it

anti-clockwise 1 turn for the Triple ring,7/8 turn for the Fish,3/4 turn for the Rapid,1/2 turn for the Semi-

Rapid and 3/8 turn for the Auxiliary .

NG TO LPG: Use a thin blade screwdriver to turn the by-pass screw located above left of the gas valve

shaft as shown right.Turn gently the by-pass screw clockwise to the end.

Burner

Consumption(*)

LPG Natural gas

By pass

Main Injector

Test point pressure 29mbar 20mbar

Rapid

Semi-rapid

Auxiliary

Triple ring

0.44

0.34

0.29

0.64 0.95

0.50

0.65

0.85

3.7

1.0

1.75

3.0 1.18

0.97

0.72

1.40

Main Injector

(*) = With dry gas and with greater calorific power (Hs ) at 15 and 1013.26 mbar

1 = grid

2 = burner cap

3 = burner head

4 = spark plug

5 = safety valve (for models equipped with a safety valve)

2 2

Input

kw(g/h)

Instructions for Use

(gas cooking top side)

Description of the main parts of the appliance

Waring:

1 This appliance shall be installed in accordance with the regulations in force and only used in a well

ventilated space( .

Read the instructors before installing or using this appliance.

2 The use of a gas cooking appliance results in the production of heat and moisture in the room in which it

is installed. Ensure that the kitchen is well ventilated: keep natural ventilation holes open or install a

mechanical ventilation device (mechanical extractor hood).

3 Prolonged intensive use of the appliance may call for additional ventilation, for example opening of a

window,or more effective ventilation, for example increasing the level of mechanical ventilation where

present.

DO not use the appliance in the carbarn,basement and the room without window)

Burner and injector characteristic table Burner and injector characteristic table

Main Injector

0.95

0.50

0.65

0.85

Input

kw(g/h)

3.7(269)

1.0(72.7)

1.75(127)

3.0(218)

I3B/P(30) I3+(28-30/37)

3.7(264)

1.0(71)

1.75(125)

3.0(214)

37mbar

This manual suits for next models

Table of contents

Other Eurotech Range manuals

Eurotech

Eurotech EUR-FSC60 User manual

Popular Range manuals by other brands

Samsung

Samsung FCQ321HTUW Service manual

Kenmore

Kenmore 790.45712 Use & care guide

Wolf

Wolf CHR CHSSR owner's manual

Smeg

Smeg Built-in Microwave Oven Instructions for the user

Zanussi

Zanussi ZCG054G user manual

Whirlpool

Whirlpool 8575985-W Warranty

Frigidaire

Frigidaire 316000635 owner's guide

GE JCSS630 quick start guide

Samsung

Samsung NX58M9960P series installation manual

Hotpoint

Hotpoint RB524R Use and care & installation instructions

Whirlpool

Whirlpool Roper FGP305KW3 Use & care guide

Amana

Amana ART6610 SERIES owner's manual

Maytag

Maytag MERH770WB Use & care guide

Fulgor Milano

Fulgor Milano SOFIA Use & care manual

Premier

Premier EF-4358GH instruction manual

Kenmore

Kenmore 790.9010 Series Use & care guide

KitchenAid

KitchenAid KESC300 Use and care guide

Frigidaire

Frigidaire FFEF3012LS Service data sheet