EuroFans Atlanta Setup guide

OWNERS INSTRUCTION

MANUAL

30”/76cm

Atlanta

INSTALLATION

OPERATION

MAINTENANCE

PAGE 1

CAUTION

READ INSTRUCTIONS CAREFULLY FOR SAFE INSTALLATION

AND FAN OPERATION. IF UNSURE CONSULT

A QUALIFIED ELECTRICIAN

PAGE 2

SUITABLE FOR 230V/50 CYCLE ELECTRICAL SUPPLY

Enquirie on in talling your fan plea e call our help line on

01959-56 0

PAGE 3

Safety Precautions

1. To ensure the success of the installation be sure to read the instructions and study the

diagrams thoroughly before commencing.

2. All electrical work should only be undertaken after disconnection of the power by

removing fuses or turning off the circuit breaker to ensure all pole isolation of the

electrical supply. If you are in any doubt the services of a qualified electrician should

be sought to ensure that all work is carried out in accordance with the I.E.E.

Regulations, current good practice and other national and local electrical codes.

3. Make sure that your installation sits will not allow the rotating fan blades to come into

contact with any object and that there is a minimum clearance of 150mm (6”) from the

blade tip to the wall or ceiling. Please note that the bigger this clearance is the better

the airflow from your fan will be. Ensure the blades are mounted at a minimum height

of 2.3 meters (7’6”) from the floor when the fan is installed.

. The fixing point for the fan must be able to support a weight of ten times that of the net

weight of the fan. Net weights can be found on the bottom of the unit’s box. If you are

mounting the fan to a ceiling junction box, the box and it’s fixing must be able to

support the moving weight of the fan and must not twist or work loose.

5. The fan must be earthed.

6. Do not connect the fan motor to a dimmer switch. This may give an unsatisfactory

performance (motor hum) and cause damage to the motor.

7. It is not recommended that ceiling fans and gas appliances are operated in the same

room at the same time.

8. The fan must be turned off and stopped completely before reversing the fan direction.

This will prevent any damage to the motor of the unit or controller (if installed).

9. Do not insert anything into the fan blades while the fan is operating. This will damage

the blades and upset the balance of the unit causing the unit to wobble.

10. After the fan is completely installed make sure that all connections are secure

and tight to prevent any problems.

11. Because of the fan’s natural movement, some connections may loosen. Check the

support connections, brackets and blade attachments twice a year to make sure they

are all secure. If they are loose tighten with a screwdriver.

Note: The important safeguards and instructions given in this manual are not meant to

cover all possible conditions and situations that may occur. It must be understood that

common sense, caution and care are factors, which cannot be built into any product. These

factors must be supplied by the persons caring for and using the unit.

For installation advice, or in the unlikely event of damaged or missing parts please ring:

HELPLINE: (01959) 56 0

PAGE 4

Supplied Parts

One fan motor assembly

One round plate fitted with terminal block and top rubber washers.

One set of blades

One set of blade carriers

One screw-pack with balancing kit

One installation booklet.

Only supplied on units supplied with pre-fitted lights

One light fitting – factory fitted

One shade, one screw pack for light shade

Tools and Materials Required

Philips screwdriver

Blade screwdriver

Small electrical screwdriver

Electrical pliers

Step ladder

Wiring supplies as required by current electrical practice

Bulbs if a light fitting is fitted / to be fitted

In-line crimps or other suitable connectors if an extension rod in excess

of 760mm (30 inch) is to be fitted.

Before starting the assembly and installation of your fan please ensure the safety

precautions have been read and understood.

Installation Difficulties, Missing or Damaged Parts

If you have any difficulty in installing your fan/light or if you are unfortunate enough to

find that your fan have been dispatched with parts missing or damaged please contact

our help-line on (01959 56 0). We will be very pleased to provide help or forward

replacements parts to your immediately.

In any communication with us please quote model reference, colour of the unit and the

part missing /damaged.

HELPLINE

01959 56 0

PAGE 5

ASSEMBLING AND HANGING YOUR CEILING FAN

NOTE:

Before installing ensure that you have all poles disconnection of the electricity

supply and that you refer to q qualified electrician to ensure that all wiring is carried

out in accordance with I.E.E. Regulations, current good practice, national and local

electrical codes.

A. CLOSE TO CEILING MOUNTING

STEP 1: MOUNTING PLATE INSTALLATION

Loosen the screw of the mounting plate from canopy.

Secure the mounting plate to joist with wood screws, rubber and steel

washers. (See Fig. 1)/page .

CAUTION: Be sure that the mounting location can support load of

at 70 kilos. (see Safety Precautions)

STEP 2: HANGING

Hang the motor on mounting plate with temporary support (a hook)

(See Fig. 2)/page .

This is an aid in marking the electrical connection.

STEP 3 : WIRING (See Page 7)

CAUTION: Carefully read the WIRING INSTRUCTIONS and DIAGRAMS

Since improper installation may result in an electric short and

void the warranty

STEP : FAN HANGING

Carefully push all wiring into canopy. Life off temporary

mount and position fan motor on mounting plate such that

attachment screws align with keyed slots on upper side of

motor housing secure the fan to mounting plate with serrated

washers and screws provided (See Fig. 3). Ensure a good

electrical connection by breaking lacquer finish as this forms

the earth.

STEP 5 : FAN ASSEMBLING

Turn on the electricity. Check to see that the fans forward and

reverse speeds work properly see operating instructions.

STEP 6: GLASS ASSEMBLING

The light fitting has been pre-assembled to your fan

(See Fig. 3) 60 watts max. Bulb (not provided) can be fitted. The

shade is held in place by three thumbscrews, do not over

tighten.

PAGE 6

FLUSH MOUNT STYLE ASSEMBLY DIAGRAMS

PAGE 7

B. DROP ROD STYLE INSTALLATION

STEP 1 : MOUNTING PLATE INSTALLATION

Loosen the screw of the mounting plate from canopy.

Secure the mounting plate to joist with wood screws, rubber and steel

washers. (See Fig. )

CAUTION : Be sure that the mounting location can support load of

at 70 kilos. (See Safety Precautions)

STEP 2 : DROP ROD ASSEMBLY

Remove the three screws from boss of top housing to move the canopy

from fan. (SEE FIG. 5)

Remove the cotter pin and split pin from the bottom of the drop rod. If a

longer drop rod is going to be used, transfer the ball joint and the earth

wire to the longer rod.

Put the drop rod through the flared end of the canopy and pass the

electrical supply leads from the top of the motor through the drop rod

until they exit at the top of the ball joint. Always ensure the rod passes

through the canopy before the rod is connected to the fan. If an

extension rod longer than 30 inches is to be used, the cables will need to

be extended in an appropriate way.

Loosen the drop rod set screws on the boss, which is on top of the

motor and insert the drop rod into the drop rod boss on top of the motor

casing. Turn gently to align the holes in the boss with those in the rod.

Ease the cotter pin through the boss and the rod taking care not to pinch

or damage any cables. Fix in place by replacing the split pin.

Hang the motor on mounting plate with temporary support (a hook) for

connecting wire. (SEE FIG. 6)

STEP 3 : WIRING (See Page 7)

CAUTION: Carefully read the WIRING INSTRUCTIONS and DIAGRAMS

Since improper installation may result in an electric short and

void the warranty

STEP : FAN HANGING

Carefully push all wiring into canopy. Life off temporary

mount and position fan motor on mounting plate such that attachment

screws align with keyed slots on upper side of motor housing secure the

fan to mounting plate with serrated washers and screws provided.

Ensure a good electrical connection by breaking lacquer finish as this

forms the earth.

STEP 5 : FAN ASSEMBLING

Turn on the electricity. Check to see that the fans forward and reverse

speeds work properly see operating instructions.

Blades assembly, get more details at page 8.

STEP 6: GLASS ASSEMBLING

The light fitting has been pre-assembled to your fan

(See Fig. ) 60 watts max. Bulb (not provided) can be fitted. The shade is

held in place by three thumb screws, do not over tighten.

PAGE 8

DROP ROD STYLE ASSEMBLY DIAGRAMS

PAGE 9

WIRING INSTRUCTIONS

NOTE:

Before installation ensure that you have all pole disconnection of the electricity supply

and that you refer to a qualified electrician to ensure that all wiring is carried out in

accordance with I.E.E. Regulations current goods practice national and local electrical

codes.

Carefully read the wiring instructions and diagrams since improper installation may result

in an electrical short and void the warranty.

In most cases connect the fan motor BROWN wire to the supply wire coloured RED or

BROWN, connect the fan motor neutral BLUE wire to the neutral supply normally coloured

BLUE or BLACK, connect the mounting plate GREEN or GREEN/YELLOW earth wires to

the earth supply. SEE FIG. 8

When underlight is attached, connect the ORANGE light wire to the supply live wire,

normally coloured RED or BROWN. If light to be independently operated from a wall

switch a separate live supply is required. SEE FIG.9

If fan is controlled independently from a wall switch. SEE FIG. 10

If a separate wall control is to be used for both fan and light please see wiring diagram

supplied with control or SEE FIG. 11.

Check to see that all your connections are tight and that no bare wires are visible of

touchable at any of the wire connectors. Except for the earth wire. Gently tuck all of the

completed wiring carefully into the canopy.

CAUTION: THIS APPLIANCE MUST BE EARTHED, IMPORTANT. Do not connect the

motor supply cable to a dimmer switch. If a wall mounted control for the

fan is required then we recommend you contact our help-line.

PAGE 10

Assembling the blades

The blades now need to be assembled on to the carrier brackets.

Note that blades can be installed with either surface facing down.

Carefully unwrap the blade and a carrier bracket. Align the bracket with the holes in

the blades and use the screws and fibre washers provided to connect them.

The fibre washer should go on top the blade between the head of the screw and the

surface of the blade. Ensure the screws are tightened up firmly.

Repeat this process for all blades.

Attach the assembled blades onto the fan

Release motor screws from fan motor, then, put blade carrier with blade on the

motor. Using motor screws to screw it. Please make sure it is tight enough. Be

careful not to bend the blades or the carrier brackets during installation as this

may result in an imbalance and induce wobble.

If installing more than one fan be careful not to mix the blade sets. Each set is

carefully manufactured to be evenly balanced, mixing would break up a balanced

set and again this could induce wobble.

Operating instructions

Having checked that all electrical connections are securely made and insulated,

turn on the power and check the operation of the fan. The pull switch on the side of

the motor housing is the selection switch for the speed function of the fan and is

also the on/off function. The first pull from the off position takes you on to the high

speed; the second on to medium speed; the third on to slow speed and the fourth

pull to the off position.

The slide switch on the other side of the switch housing changes the direction of

rotation of the blades. (Remember to let the fan slow to a complete stop before

changing the direction of rotation). When looking up at the fan blades, anti –

clockwise rotation achieves a downward flow of air and clockwise rotation achieves

an upward movement of air.

Summer operation – In warm weather a downward movement of air is more

desirable as this achieves a greater cooling effect.

Winter operation – In winter a movement of air moving upwards and then back

down the sides of the room achieves a more balanced temperature throughout the

room.

Table of contents

Other EuroFans Fan manuals

EuroFans

EuroFans MORENO Setup guide

EuroFans

EuroFans MONTANA Setup guide

EuroFans

EuroFans Neptune Setup guide

EuroFans

EuroFans Atom Setup guide

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual