EtherWAN EX48000A Series User manual
Hardened PoE Ethernet Switch
Quick Start Guide
This quick start guide describes how to install and use the
Hardened PoE Ethernet Switch. This is the switch of choice
for harsh environments constrained by space.
Physical Description
The Port Status LEDs and Power inputs
1
Hardened PoE Ethernet Switch
LED State Indication
Steady Power on.
Power1
Power2
Power3 Off Power off.
Steady Power redundant system failure occurred.
Fault Off Power redundant system failure is not
occurred.
10/100Base-TX, 100Base-FX/BX
Steady A valid network connection established.
Link/ACT Flashing Transmitting or receiving data.
ACT stands for ACTIVITY.
Steady Valid port connection at 100Mbps.
10/100 Off Valid port connection at 10Mbps.
Power Input Assignment
Power3 48VDC DC Jack
＋48VDC
Power2 －Power Ground
＋48VDC
Power1 －Power Ground
Earth Ground
Terminal Block
Relay Output Rating 1A @ 24VDC
Relay Alarm Assignment
FAULT
*Relay warning signal disable for following:
The relay contact closes if Power1 and
Power2 are both failed but Power3 on.
The relay contact closes if Power3 is failed
but Power1 and Power2 are both on.
DC Terminal Block Power Inputs: There are two pairs of
power inputs can be used to power up this switch. Redundant
power supplies function is supported.
The 10/100Base-TX and 100Base-FX/BX Connectors
1. The 10/100Base-TX Connections
The following lists the pinouts of 10/100Base-TX ports.
2
Hardened PoE Ethernet Switch
Pin PoE Ports (Port 1-4) Non-PoE Port (Port 5)
1 Output Transmit Data + Output Transmit Data +
2 Output Transmit Data - Output Transmit Data -
3 Input Receive Data + Input Receive Data +
4 Positive (VCC+)
5 Positive (VCC+)
6 Input Receive Data - Input Receive Data -
7 Negative (VCC-)
8 Negative (VCC-)
2. The 100Base-FX Connections
The fiber port pinouts: The Tx (transmit) port of device I is
connected to the Rx (receive) port of device II, and the Rx
(receive) port of device I to the Tx (transmit) port of device II.
3. The WDM 100Base-BX Connections
The fiber port pinouts: Only one optical fiber is required to
transmit and receive data.
3
Hardened PoE Ethernet Switch
4
Functional Description
•Meets NEMA TS1 & TS2 Environmental requirements:
temperature, shock, and vibration for traffic control
equipment.
•Meets EN61000-6-2 & EN61000-6-4 EMC Generic
Standard Immunity for industrial environment.
•Supports IEEE802.3af Power over Ethernet (PoE)
Power Sourcing Equipment (PSE).
•Supports IEEE802.3/802.3u/802.3x. Auto-negotiation:
10/100Mbps, Full/Half-duplex, Auto-Negotiation, Auto
MDI/MDIX.
•100Base-FX: Multi/Single mode SC or ST type,
100Base-BX: WDM Multi/Single mode SC type.
•Supports 1024 MAC addresses. Provides 512K bits
buffer memory.
•Alarms for power and port link failure by relay output.
•Power Supplies: Redundant 48VDC Terminal Block
power inputs and 48VDC DC JACK with optional
100-240VAC external power supply.
•Operating voltage and Max. current consumption: 1.5A
@ 48VDC. Power consumption: 72W Max.
•-40 to 75 (℃℃-40℉to 167℉) operating temperature
range. Tested for functional operation @ -40 to 85℃℃
(-40℉to 185℉).
•Supports Desktop installation.
Hardened PoE Ethernet Switch
5
Preface
A member of the growing family of rugged switches, this
Hardened PoE Ethernet Switch addresses a need for a
smaller switch. This switch provides an affordable solution
for rugged and outdoor environment, transportation
road-side cabinet, industrial floor shop, multitenant
dwellings or Fiber To The Home (FTTH) applications.
Capable of operating at temperature extremes of -40°C to
+75°C, this is the switch of choice for harsh environments
constrained by space.
Port 1 to port 4 on this Switch supports IEEE802.3af Power
over Ethernet (PoE) Power Sourcing Equipment (PSE) and
can detect an IEEE802.3af compliant Powered Device
(PD). Using external 48VDC power inputs through
Terminal Block or Power Jack, data and power can be
transmitted to a Powered Device (PD) over the same
twisted-pair Ethernet cable through port 1 to port 4 on the
Switch.
This manual describes how to install and use the hardened
Ethernet Switch. This switch integrates full wire speed
switching technology. This switch brings the answer to
complicated hardened networking environments.
To get the most out of this manual, you should have an
understanding of Ethernet networking concepts.
In this manual, you will find:
•Features on the switch
•Illustrative LED functions
•Installation instructions
•Specifications
Hardened PoE Ethernet Switch
6
Table of Contents
QUICK START GUIDE 1
PHYSICAL DESCRIPTION 1
The Port Status LEDs and Power inputs 1
The 10/100Base-TX and 100Base-FX/BX Connectors 2
FUNCTIONAL DESCRIPTION 4
PREFACE 5
TABLE OF CONTENTS 6
PRODUCT OVERVIEW 7
HARDENED POEETHERNET SWITCH 7
PACKAGE CONTENTS 7
PRODUCT HIGHLIGHTS 8
Basic Features 8
FRONT PANEL DISPLAY 9
PHYSICAL PORTS 10
INSTALLATION 11
SELECTING A SITE FOR THE SWITCH 11
CONNECTING TO POWER 12
Redundant DC Terminal Block Power Inputs 12
48VDC DC Jack 12
Alarms for Power and Port Link Failure 13
CONNECTING TO YOUR NETWORK 14
Cable Type & Length 14
Cabling 15
SPECIFICATIONS 16
Hardened PoE Ethernet Switch
Product Overview
Hardened PoE Ethernet Switch
Package Contents
When you unpack the product package, you shall find the
items listed below. Please inspect the contents, and report
any apparent damage or missing items immediately to your
authorized reseller.
3This Switch
3User’s Manual
3External power adapter & Power Cord (Optional)
7
Hardened PoE Ethernet Switch
8
Product Highlights
Basic Features
•Meets NEMA TS1 & TS2 Environmental requirements:
temperature, shock, and vibration for traffic control
equipment.
•Meets EN61000-6-2 & EN61000-6-4 EMC Generic
Standard Immunity for industrial environment.
•Supports IEEE802.3af Power over Ethernet (PoE)
Power Sourcing Equipment (PSE).
•Supports IEEE802.3/802.3u/802.3x. Auto-negotiation:
10/100Mbps, Full/Half-duplex, Auto-Negotiation, Auto
MDI/MDIX.
•100Base-FX: Multi/Single mode SC or ST type,
100Base-BX: WDM Multi/Single mode SC type.
•Supports 1024 MAC addresses. Provides 512K bits
buffer memory.
•Alarms for power and port link failure by relay output.
•Power Supplies: Redundant 48VDC Terminal Block
power inputs and 48VDC DC JACK with optional
100-240VAC external power supply.
•Operating voltage and Max. current consumption: 1.5A
@ 48VDC. Power consumption: 72W Max.
•-40 to 75 (℃℃-40℉to 167℉) operating temperature
range. Tested for functional operation @ -40 to 85℃℃
(-40℉to 185℉).
•Supports Desktop installation.
Hardened PoE Ethernet Switch
Front Panel Display
Status LEDs
LED State Indication
Steady Power on.
Power1
Power2
Power3 Off Power off.
Steady Power redundant system failure occurred.
Fault Off Power redundant system failure is not
occurred.
10/100Base-TX, 100Base-FX/BX
Steady A valid network connection established.
Link/ACT Flashing Transmitting or receiving data.
ACT stands for ACTIVITY.
Steady Valid port connection at 100Mbps.
10/100 Off Valid port connection at 10Mbps.
9
Hardened PoE Ethernet Switch
10
Physical Ports
This switch series provides two different combinations of
RJ-45 copper and fiber ports as below:
•Five 10/100Base-TX ports
•Four 10/100Base-TX ports + one 100Base-FX/BX port
CONNECTIVITY
•RJ-45 connectors
•SC or ST connector on 100Base-FX fiber port.
•SC connector on 100Base-BX fiber port.
<Note> Different product model supports different type of
fiber connector.
This manual suits for next models
1
Table of contents
Other EtherWAN Switch manuals
EtherWAN
EtherWAN EX46910F User manual
EtherWAN
EtherWAN EX32908 series User manual
EtherWAN
EtherWAN EX16908 User manual
EtherWAN
EtherWAN EX78900X Series User manual
EtherWAN
EtherWAN EX61000A User manual
EtherWAN
EtherWAN EX77000 Series User manual
EtherWAN
EtherWAN OttoE TF100 Sereis User manual
EtherWAN
EtherWAN EX33000 Series User manual
EtherWAN
EtherWAN EX42908 series User manual
EtherWAN
EtherWAN EX70900 User manual
EtherWAN
EtherWAN EX33000 Series User manual
EtherWAN
EtherWAN EG97000 Series User manual
EtherWAN
EtherWAN EX93000 User manual
EtherWAN
EtherWAN EX77964 User manual
EtherWAN
EtherWAN EX17162A User manual
EtherWAN
EtherWAN EX42300 series User manual
EtherWAN
EtherWAN EX45900 series User manual
EtherWAN
EtherWAN EX75900 Series User manual
EtherWAN
EtherWAN EX19082 User manual
EtherWAN
EtherWAN EX17908 Series User manual
