EtherWAN EL1033 User manual
Industrial PoE Media Converter
1
Quick Start Guide
This quick start guide describes how to install and use the
Industrial PoE Media Converter. This is the Media Converter
of choice for harsh environments constrained by space.
Physical Description
The Terminal Block and Power inputs
Power Input Assignment
＋48VDC
Power 1 －Power Ground
Earth Ground
Terminal Block
Power 2 48VDC DC Jack
DC Terminal Block Power Inputs: There are two power inputs
that can be used to power up this Industrial PoE Media
Industrial PoE Media Converter
2
Converter. Redundant power supplies function is supported.
The DIP Switch
DIP
Switch
On Off
1 Enable forced mode for TX port Enable auto negotiation for TX port
2 TX port forced to 10Mbps TX port forced to 100Mbps
3 TX port forced to half duplex mode TX port forced to full duplex mode
4 Enable Link-Fault-Pass-Through Disable Link-Fault-Pass-Through
The 10/100Base-TX and 100Base-FX Connectors
1. The 10/100Base-TX Connections
The following lists the pinouts of 10/100Base-TX ports.
Pin Regular Ports Uplink port
1 Input Receive Data + Output Transmit Data +
2 Input Receive Data - Output Transmit Data -
3 Output Transmit Data + Input Receive Data +
4 NC NC
5 NC NC
6 Output Transmit Data - Input Receive Data -
7 NC NC
8 NC NC
2. The 100Base-FX Connections
The fiber port pinouts: The Tx (transmit) port of device I is
connected to the Rx (receive) port of device II, and the Rx
(receive) port of device I to the Tx (transmit) port of device II.
Industrial PoE Media Converter
3
3. The WDM 100Base-FX Connections
The fiber port pinouts: Only one single-mode optical fiber is
required to transmit and receive data.
The Port Status LEDs
Industrial PoE Media Converter
4
LED State Indication
Power over Ethernet (PoE)
Steady Power Sourcing Equipment (PSE) is connected.
PD Power Off Power Sourcing Equipment (PSE) is disconnected.
10/100Base-TX, 100Base-FX
Steady A valid network connection established.
Link/ACT Flashing Transmitting or receiving data.
ACT stands for ACTIVITY.
DIN-Rail Kits, Optional Wall Mounting Kits
Functional Description
•Meets EN61000-6-2 & EN61000-6-3 EMC Generic
Standard Immunity for industrial environment.
•Supports IEEE802.3af Power over Ethernet (PoE)
Power Device (PD).
•DIP Switch configuration for “Link-Fault-Pas-Through”,
speed, duplex mode.
Industrial PoE Media Converter
5
•Supports IEEE802.3/802.3u/802.3x. Auto-negotiation:
10/100Mbps, Full/Half-duplex, Auto-Negotiation, Auto
MDI/MDIX.
•100Base-FX: Multi/Single mode SC or ST type, WDM
Single mode SC type.
•Supports 1024 MAC addresses. Provides 2.25M bits
buffer memory.
•Power Supplies: Redundant 48VDC Terminal Block
power input and 48VDC DC JACK with 100-240VAC
external power supply. “For use with Model AS-120P-48
as power jack supply source by MEAN WELL
Enterprises Co., Ltd.".
•Operating voltage and Max. current consumption:
0.075A @ 48VDC. Power consumption: 3.6W Max.
•-10 to℃60 (℃14℉to 140℉) operating temperature
range.
•Supports DIN-Rail, Panel, or Wall Mounting installation.
Assembly, Startup, and Dismantling
•Assembly: Place the Media Converter on the DIN rail
from above using the slot. Push the front of the Media
Converter toward the mounting surface until it audibly
snaps into place.
•Startup: Connect the supply voltage to start up the
Media Converter via the terminal block (or DC JACK).
•Dismantling: Pull out the lower edge and then remove
the Media Converter from the DIN rail.
Industrial PoE Media Converter
6
Industrial PoE Media Converter
7
Preface
A member of the growing family of Industrial Media
Converters, this Industrial PoE Media Converter addresses
a need for a Power over Ethernet (PoE) Media Converter.
Capable of operating at temperature extremes of -10℃ to
+60℃, this is the Media Converter of choice for harsh
environments.
The 10/100Base-TX port on this Media Converter supports
IEEE802.3af Power over Ethernet (PoE) Powered Device
(PD) and can be detected by an IEEE802.3af compliant
Power Sourcing Equipment (PSE). Data and power can be
transmitted from 10/100Base-TX port on Power Sourcing
Equipment (PSE) to Powered Device (PD) Media
Converter over the same twisted-pair Ethernet cable
through 10/100Base-TX port on the Powered Device (PD)
Media Converter. Powered Device (PD) Media Converter
also can use external 48VDC power inputs through
Terminal Block or Power Jack.
This manual describes how to install and use the Industrial
PoE Media Converter. This Media Converter integrates full
wire speed switching technology. And this Media Converter
brings the answer to complicated hardened networking
environments.
To get the most out of this manual, you should have an
understanding of Ethernet networking concepts.
In this manual, you will find:
•Features on the Media Converter
•Illustrative LED functions
•Installation instructions
•Specifications
Industrial PoE Media Converter
8
Table of Contents
QUICK START GUIDE 1
PHYSICAL DESCRIPTION 1
The Terminal Block and Power inputs 1
The DIP Switch 2
The 10/100Base-TX and 100Base-FX Connectors 2
The Port Status LEDs 3
DIN-Rail Kits, Optional Wall Mounting Kits 4
FUNCTIONAL DESCRIPTION 4
ASSEMBLY,STARTUP,AND DISMANTLING 5
PREFACE 7
TABLE OF CONTENTS 8
PRODUCT OVERVIEW 9
INDUSTRIAL POEMEDIA CONVERTER 9
PACKAGE CONTENTS 9
PRODUCT HIGHLIGHTS 10
Basic Features 10
FRONT PANEL DISPLAY 11
PHYSICAL PORTS 12
INSTALLATION 13
SELECTING A SITE FOR THE MEDIA CONVERTER 13
DIN RAIL MOUNTING 14
CONNECTING TO POWER 15
DC Terminal Block Power Input 15
48VDC DC Jack 15
DIP SWITCH 16
CONNECTING TO YOUR NETWORK 17
Cable Type & Length 17
Cabling 18
SPECIFICATIONS 19
Industrial PoE Media Converter
9
Product Overview
Industrial PoE Media Converter
Package Contents
When you unpack the product package, you shall find the
items listed below. Please inspect the contents, and report
any apparent damage or missing items immediately to your
authorized reseller.
3This Media Converter
3User’s Manual
3External power adapter & Power Cord
(Optional)
Industrial PoE Media Converter
10
Product Highlights
Basic Features
•Meets EN61000-6-2 & EN61000-6-3 EMC Generic
Standard Immunity for industrial environment.
•Supports IEEE802.3af Power over Ethernet (PoE)
Power Device (PD).
•DIP Switch configuration for “Link-Fault-Pass-Through”,
speed, duplex mode.
•Supports IEEE802.3/802.3u/802.3x.
•Auto-negotiation: 10/100Mbps, Full/Half-duplex; Auto
MDI/MDIX.
•100Base-FX: Multi/Single mode SC or ST type, WDM
Single mode SC type.
•Supports 1024 MAC addresses.
•Provides 2.25M bits buffer memory.
•Power Supplies: Redundant 48VDC Terminal Block
power input and 48VDC DC JACK with 100-240VAC
external power supply. “For use with Model AS-120P-48
as power jack supply source by MEAN WELL
Enterprises Co., Ltd.".
•Operating voltage and Max. current consumption:
0.075A @ 48VDC. Power consumption: 3.6W Max.
•-10℃to 60℃(14℉to 140℉) operating temperature
range.
•Supports DIN-Rail, Panel, or Wall Mounting installation.
Table of contents
Other EtherWAN Media Converter manuals
EtherWAN
EtherWAN EL100 User manual
EtherWAN
EtherWAN EMC1200R User manual
EtherWAN
EtherWAN EL900 Series User manual
EtherWAN
EtherWAN EL900 Series User manual
EtherWAN
EtherWAN EL2211 User manual
EtherWAN
EtherWAN EL2242 User manual
EtherWAN
EtherWAN EL900 Series User manual
EtherWAN
EtherWAN EL100T User manual
EtherWAN
EtherWAN EL50 Series User manual
EtherWAN
EtherWAN EMC400 User manual
EtherWAN
EtherWAN EL42011 Series User manual
EtherWAN
EtherWAN EL1141 Series User manual
EtherWAN
EtherWAN EL100 User manual
EtherWAN
EtherWAN EM1100 User manual
EtherWAN
EtherWAN EL50 Series User manual
EtherWAN
EtherWAN EL9100 User manual
EtherWAN
EtherWAN EL2321 User manual
EtherWAN
EtherWAN EL900 Series User manual
EtherWAN
EtherWAN EMC1200R User manual
EtherWAN
EtherWAN EL1032T Series User manual
