Etac Turner PRO Instructions for use

Turner PRO

2

Wheels / Wheel axles

3

Rotating mechanism

2

If turner rotates porly:

• Unscrew bolt (5).

• Clean Low friction disc (2) and ﬂoor plate (1).

• If deep groves or damages in (1) or (2), replace

(1,2,3,4,5).

• Apply loctite 243 or simular on bolt (5), tighten bolt

ﬁrmly (approx 20Nm).

If antislip knobs are missing or worn down:

• Flip out old knobs (3).

• Clean holes and push in new knobs.

Washing

1

• Lay the Turner PRO on the ﬂoor in an angeled position

after washing, so the water runs out of the rotating

mechanism.

• You may also use copressed air to blow dry inside

rotating mechanism.

• Controls wheel and shaft for wear.

• Check if the wheels turn easily, remove hair and dirt.

If wheels are worn out, or still rotates porly after

cleaning:

3

1

5

4

2

• Use a solvent-free detergent with a pH level bet-

ween 5 and 9.

• Can be washed at 70° C for 10 minutes.

3

1

2

• Flip out starlock with

an screwdriver or

simular (1).

• Remove bolt and

wheel.

• Replace 1,2,3.

• Place wheel between

forks.

• Insert bolt and knock

.starlock in place.

EN

Reconditioning

Turner PRO

3

Leg Support

4

Main plate/outer pole

5

• Check bracket on leg support for cracks and

wear. If cracs, replace coplete leg support.

• Check cushion for wear, should be tight and ﬁrm

around the pipe. If loose or damaged, replace

cushion.

Original spare parts from Etac should always be used.

Handle/inner pole

6

• Check for cracs and dents, if cracs or dents

replace inner pole.

2

3

1

If complete leg support needs to be replaced:

• Unscrew bolts and remove outer pole.

• Pull leg support out of pole.

If cushion need to be replaced:

• Flip out knob (3) and remove cushion.

• Clean pipe, insert new cushion and knock knob in

place.

• Insert leg support with kneepads pointing upwards

• Make sure both knobs are on the same side (1).

• Tighten knob by turning knob clockwise (2).

• Place the base plate on an even surface. Insert

pole with knee pads facing away from

the wheels.(1)

• Insert all three screws into holes in the base

plate. Use allen key to screw in bolts. Apply

loctite 243 or simular on bolts, tighten

bolt ﬁrmly, (approx 20Nm). (2)

12

12

• Check for cracks and wear on main plate and

outer pole. If cracks, replace complete Turner-

PRO.

• Check bolted conection between pole and

main plate (3 bolts), if loose bolts tighten all

bolts.

EN

Reconditioning

Reconditioning

Other manuals for Turner PRO

3

Other Etac Mobility Aid manuals

Popular Mobility Aid manuals by other brands

Alber

Alber Scalamobil iQ operating instructions

Ferno

Ferno CCT-PX user manual

HEPRO

HEPRO Gripo user manual

Otto Bock

Otto Bock Pheon 3R62 Instructions for use

NRS Healthcare

NRS Healthcare M11090 User instructions

Medline

Medline MDS86835DSHEC User Instructions & Warranty

Guldmann

Guldmann Twin Turner II user manual

Drive

Drive ROOMBA Operation manual

Gate

Gate Balder operating instructions

Decon wheel

Decon wheel TNS Notos Assembly instructions

ExoAtlet

ExoAtlet ExoAtlet-II user manual

Invacare

Invacare Storm Series parts catalog

Rhythm Healthcare

Rhythm Healthcare B3800F manual

AMF-BRUNS

AMF-BRUNS PROTEKTOR installation manual

Drive DeVilbiss Healthcare

Drive DeVilbiss Healthcare OTTER Instructions for use

Rhythm Healthcare

Rhythm Healthcare C500U Assembly and Fitting Instructions

Lumex

Lumex RJ4200A manual

Rebotec

Rebotec Jumbo user manual