ESYLUX MD 180i/16 BASIC CH User manual

ESYLUX GmbH | An der Strusbek 40

22926 Ahrensburg | Germany

[email protected] | www.esylux.com

Operating instructions

MD 180i/16 BASIC

EB10430459

MD 180i/16 BASIC CH

EB10430602

MA00564901

06/2017

OPERATING INSTRUCTIONS

MD 180i/16 BASIC

MD 180i/16 BASIC CH

2 / 19

Table of contents

1 Description 3

2 Safety instructions 3

3 Operation / functionality 4

3.1 Conditions in which the lighting is switched on 4

3.2 Conditions in which the lighting is switched off 4

3.3 Switching delay – not in pulse mode 5

4 Installation / connection 5

4.1 Masking the field of detection 6

5 Activation 7

5.1 Overview of factory settings 7

6 Settings 7

6.1 Control via external “S” button 7

6.2 Configuring parameters via remote control 8

6.3 Mobil-PDi/MDi 8

6.4 Mobil-PDi/MDi temporary settings 9

6.5 Programming the Mobil-PDi/MDi 10

6.6 Mobil-PDi/MDi-universal 12

6.7 Mobil-PDi/MDi-universal temporary settings 12

6.8 Programming the Mobil-PDi/MDi-universal 13

6.9 “12 h ON / OFF” function 16

7 Technical data 17

8 Troubleshooting 18

8.1 Maintenance 18

8.2 Cleaning 19

9 ESYLUX manufacturer's guarantee 19

OPERATING INSTRUCTIONS

MD 180i/16 BASIC

MD 180i/16 BASIC CH

3 / 19

1 Description

The ESYLUX wall-mounted motion detector is a passive infrared presence detector

which responds to moving heat sources, such as people walking.

The motion detector is designed for areas with low levels of natural light, such as

hallways, cellars, staircases, changing rooms, toilets, garages etc.

Parameters can be configured using the ESYLUX Mobil-PDi/MDi and Mobil-PDi/MDi-

universal remote controls.

Note: Use this product only as intended (as described in the user instructions).

The device must not be changed, modified or painted – doing so will void any warranty

claims. You must check the device for damage immediately after unpacking it. If there

is any damage, you should not install the device under any circumstances.

If you suspect that safe operation of the device cannot be guaranteed, you should turn

the device off immediately and make sure that it cannot be operated unintentionally.

2 Safety instructions

• Work on the 230-V power system must be carried out by authorised personnel only,

with due regard to the applicable installation regulations / standards

• Switch off the power supply before installing the system

• On the input side, the device is to be protected against short circuits with a 10-A circuit

breaker

• Protection type IP 40 for interior use

OPERATING INSTRUCTIONS

MD 180i/16 BASIC

MD 180i/16 BASIC CH

4 / 19

3 Operation / functionality

• The ESYLUX wall-mounted motion detector, which has a 180° field of detection,

is only suitable for wall mounting

• The range is up to 16 m in diameter at a recommended installation height

of 1.10 - 2.20 m

• The motion detector has one channel (C1), which is used for presence-dependent

lighting control

• The setting options can vary depending on the remote control used; please see

“Configuring parameters via remote control”

3.1 Conditions in which the lighting is switched on

The lighting is switched on if the target brightness value is below the preset lux

value and movement is detected in the field of detection. Further movement is

acknowledged by the sensor with two short flashes of the red LED (the LED can be

switched off; see “Configuring parameters via remote control”). Once the lighting has

been switched on, the sensor deactivates light measurement for this period.

3.2 Conditions in which the lighting is switched off

The lighting is switched off if no movement is detected in the field of detection and

the preset switch-off delay time has elapsed.

OPERATING INSTRUCTIONS

MD 180i/16 BASIC

MD 180i/16 BASIC CH

5 / 19

3.3 Switching delay – not in pulse mode

When persons are present, in order to avoid sudden changes in brightness caused by

undesired switching on / off of the lighting, the detector will only be triggered after a

time delay.

Example: a passing cloud could potentially cause unnecessary switching.

Time delay from light to dark: 30 sec. = red LED lights up during this period.

Time delay from dark to light: 5 min. = red LED flashes slowly during this period

4 Installation / connection

Note: Switch off the power supply before installing the system.

• The detector is designed to be installed in European flush-mounted boxes

• Specifications regarding the range of the detector relate to an ambient temperature

of approx. 20 °C

• Movement crossways to the detector is optimal for triggering the detector; head-on

approaches to the detector are more difficult to detect and therefore the range of

the detector is significantly reduced

16 m

12 m

OPERATING INSTRUCTIONS

MD 180i/16 BASIC

MD 180i/16 BASIC CH

6 / 19

• The detector should be positioned depending on the available space and usage

requirements

• Make sure that the detector has a clear line of sight, as infrared beams cannot

penetrate solid objects

• Connect the detector in accordance with the circuit diagram

Single connection

Parallel connection

LPhase, 230 V

Lighting

Neutral conductor

Push button

4.1 Masking the field of detection

Part of the field of detection can be specifically masked off using the lens mask to

avoid false alarms being caused by e.g. pets.

OPERATING INSTRUCTIONS

MD 180i/16 BASIC

MD 180i/16 BASIC CH

7 / 19

5 Activation

Connect the power supply.

A warm-up phase of 25 seconds is initiated. The red LED (for C1) and the blue LED

flash alternately: 2 x red and 1 x blue. During this time, the lighting is switched on.

5.1 Overview of factory settings

Factory settings

Light value approx. 100lux

Switch-off delay time 5 min.

Sensitivity 100 %

6 Settings

6.1 Control via external “S” button

The wall-mounted motion detector is equipped with a connection for an external

button (S terminal). This can be used to switch the lighting on and off manually.

Modes activated by pressing the external button:

Press button for approx. 1 second: The lighting is switched on or off.

Acknowledgement: green LED

Press button for approx. 3 second: The lighting is switched on or off continuously for

4 hours

Acknowledgement: red LED

Press button for approx. 5 second: The lighting is switched on or off continuously for

12 hours

Acknowledgement: blue LED

OPERATING INSTRUCTIONS

MD 180i/16 BASIC

MD 180i/16 BASIC CH

8 / 19

The LED feedback can be used to determine the mode that the wall-mounted motion

detector is currently switched to.

Example: Please release the button after approx. 3 seconds – the red LED lights up and

the “4 h ON / OFF” mode is activated.

Further parameters can be configured via remote control. Remote controls can be

purchased as accessories.

6.2 Configuring parameters via remote control

Note: For optimum reception, when programming the settings, point the remote

control at the detector. Please note that if the sensor is exposed to direct sunlight, the

standard detection range of approx. 8 m may be dramatically reduced due to the sun's

infrared rays.

6.3 Mobil-PDi/MDi (EM10425509)

OPERATING INSTRUCTIONS

MD 180i/16 BASIC

MD 180i/16 BASIC CH

9 / 19

6.4 Mobil-PDi/MDi temporary settings

Parameter configurations are only temporarily applied.

Function Customised setting

ON / OFF

Switching the lighting ON / OFF manually.

Note: The “ON / OFF” mode can be cancelled by pressing the “Reset” button.

“ON” acknowledgement: Movement detected in the field of detection is

acknowledged with two short flashes of the red LED.

“OFF” acknowledgement: Movement detected in the field of detection is

acknowledged with one short flash of the red LED.

Reset / settings

Temporarily set values are cleared and the detector returns to the manually

preset operating mode.

Test

Test mode is used for testing the field of detection and takes approx. 5 min.

During this time, the lighting is switched on. Afterwards, the detector returns

to the preset operating mode.

Acknowledgement: Movement detected in the field of detection is

acknowledged with two short flashes of the blue LED.

4 h ON / OFF

The lighting is switched on or off continuously for approx. 4 hours. If no

movement is detected in the field of detection and the preset switch-off delay

time has elapsed, the detector returns to the previous operating mode.

Note: The “4 h ON / OFF” mode can be cancelled by pressing the “Reset”

button.

OPERATING INSTRUCTIONS

MD 180i/16 BASIC

MD 180i/16 BASIC CH

10 / 19

6.5 Programming the Mobil-PDi/MDi

Alterations to parameters are applied permanently.

Function Customised setting

Enter programming mode

The detector goes into programming mode.

Acknowledgement: The blue LED lights up permanently and the lighting is

switched on continuously.

Exit programming mode

The set parameters are stored on the detector.

Acknowledgement: The blue LED is switched off.

Set the brightness switching value, max. 1000 lux

The detector switches the lighting on if the target brightness value is below the

preset lux value and movement is detected in the field of detection.

Acknowledgement: The red and blue LEDs flash three times.

Take a reading of the current ambient light value

The detector switches the lighting on if the target brightness value is below the

preset lux value and movement is detected.

Acknowledgement: The blue LED and the lighting are switched off for approx.

5 seconds while the reading is taken.

Fully automatic / semi-automatic mode

The lighting can be controlled in fully automatic and semi-automatic modes.

Fully automatic: The lighting is switched on depending on the set lux value

and movement being detected. If movement is no longer detected, the preset

switch-off delay time will start. The relevant active status can be optionally

overridden using the external “S” button.

Acknowledgement: The blue LED flashes three times.

Semi-automatic: Control (activation of the lighting) via the external “S”

button. The lighting remains switched on as long as movement is detected and

the target brightness value is greater than the preset lux value.

Acknowledgement: The blue LED is switched off for approx. 2 seconds.

Short pulse

As soon as movement has been detected in the field of detection, the detector

switches the lighting on for approx. 1 second and off for approx. 9 seconds.

This function can be used to control automatic stairwell lights, for example.

Acknowledgement: The red LED is switched on for approx. 5 seconds and off

for 5 seconds.

This manual suits for next models

Table of contents

Other ESYLUX Security Sensor manuals

ESYLUX

ESYLUX MD-C360i/6 mini User manual

ESYLUX

ESYLUX PD-C360i/8 DUO DALI User manual

ESYLUX

ESYLUX PD 360i/8 DALI ADR User manual

ESYLUX

ESYLUX EP10425806 User manual

ESYLUX

ESYLUX PROTECTOR KRF TCV 2G User guide

ESYLUX

ESYLUX PD-C360i/8 mini KNX User manual

ESYLUX

ESYLUX RC 130i User manual

ESYLUX

ESYLUX RC 130i User manual

ESYLUX

ESYLUX PD 360/8 Basic Operating and maintenance manual

ESYLUX

ESYLUX PD-C360i/24 KNX ECO User manual

ESYLUX

ESYLUX PD-FLAT 360i/6 mini DALI User manual

ESYLUX

ESYLUX EM10041006 User manual

ESYLUX

ESYLUX COMPACT APC10 DALI-2 User manual

ESYLUX

ESYLUX PD 360/8 KNX BASIC User manual

ESYLUX

ESYLUX SMB MD 360i/24 Basic SMB Operating and maintenance manual

ESYLUX

ESYLUX MD-C 180i/16 Touch Operating and maintenance manual

ESYLUX

ESYLUX PD-C360i/24 DIMplus-FM User manual

ESYLUX

ESYLUX MD-W200i User manual

ESYLUX

ESYLUX EP10426155 User manual

ESYLUX

ESYLUX PD-C180i KNX ECO User manual

ESYLUX

ESYLUX EP10427404 User manual

ESYLUX

ESYLUX RC 230i KNX User manual

ESYLUX

ESYLUX DEFENSOR MD 200 24 IR 1C IP55 WH User manual

ESYLUX

ESYLUX PD-C360i/24 DUODIMplus-FM User manual

Popular Security Sensor manuals by other brands

THORLABS

THORLABS PDA10JT user guide

Waeco

Waeco UV-DETECT operating manual

Intermatic

Intermatic IOS-DSIMF manual

urmet domus

urmet domus 1083 manual

Siemens

Siemens AZL66 Series manual

BTI

BTI Profiline Multi Finder operating instructions

Challenger

Challenger SL01 instruction manual

DMP Electronics

DMP Electronics 1122INT installation guide

Rielta

Rielta Ladoga MK-RK installation guide

Mirion Technologies

Mirion Technologies ACCURAD PRD user manual

Bosch

Bosch DS835 installation instructions

DBI SALA

DBI SALA EZ Stop User instruction manual

Lamptime

Lamptime ST05C instructions

Ubiquiti

Ubiquiti MFI-MSC quick start guide

Subsite

Subsite 910R Support

Satel

Satel OPAL Pro manual

Aleph

Aleph XC-1XTEU manual

Pima

Pima LARIS QUAD installation instructions