ESI AA780DAT User manual
INSTALLATION AND USE
AA780DAT
ARTICULATING KEYBOARD ARM
AA780DAT Rev A 4/17
Model AA780DAT
2
AA780DAT ARTICULATING KEYBOARD ARM
PLEASE REVIEW these instructions before beginning the installation. Check that
all parts needed were provided with your order. Contact your supplier if any
operates to your satisfaction.
PARTS PROVIDED
TRACK MOUN T ING TEMPLA TE
FRONT ED G E OF WO RK SURF A CE
1. Tapethis mountingtemplate to the undersideof wor
k surface.
2. Drilltwo (2) 1/8" diameterx 1/2"deep pilot
holesat markedloc
ations. Be careful not to
drillt h
rough thewor
k surface.
3. Rem
ovetemplateand install two (2) #12x 3/4" woodscrews into
pilotho
les.Leavea gap
ofapproxim
ately1/8" bet
weenth
e head
of ea
ch screwand work surface.
4. Slide trackontoscrew
s, using the keyholesin the tr
ack. Tight
en
th
escrew
sandinstall
additional screws as required, minimumof fou
r(4).
Note:If keyboard tray isdeeper than12", mou
ntbaseframeafu
rther1/2" back fromthe front
ed
ge of
work surface.
1/8" PilotHole
1/8" PilotHole
Articulating Arm (1) Track (1)
12x3/4" Screws (8)
10x3/8" Screws (2)Front Stop (1)Template (1)
Tape to Underside
of Work Surface
Note: This install
requires a powertool
or cordless drill. This is
not a handtoolinstall.
ADDITIONAL TOOLS REQUIRED
• Drill with 1
/8" bit
• #2 Phillips bit
STEP 1: Use Template to Drill Pilot Holes
• Tape the template to the underside of the work
surface. Align the “front edge” line on the
template with the front edge of the
work surface.
• Drill 1
/8" pilot holes through the
two marked locations on the
template.
— Drill the holes 5/8" deep
CAUTION: Be careful not to drill
through the work surface.
• #3 Phillips bit
3
AA780DAT ARTICULATING KEYBOARD ARM
STEP 2: Attach Track
• Remove the template and install two 3/4" wood screws into the pilot holes.
— Leave a gap of approximately 1
/8" between the head of each screw and
the work surface
• Slide the track onto the screws, using the keyholes in the track. Tighten the
screws.
• Drill pilot holes for six additional screws spaced evenly along the track.
Fasten the screws to complete the installation of the track.
Slide Small Portion
of Keyhole Under
Screw and Tighten
1
/8"
4
AA780DAT ARTICULATING KEYBOARD ARM
STEP 3: Install Articulating Arm
• Slide the articulating arm onto the track.
Position it back far enough so that
you have access to the front two
recessed holes on the track.
STEP 4: Attach Front Stop
• Position the front stop onto the
front of the track and secure it
with the 3/8" machine screws.
Front
Stop
3/8"Machine
Screw
Slide Back
OPERATION
To Raise:
• Grasp both sides of the platform and raise to the desired height.
To Lower:
• Grasp both sides of the platform, tilt up the front, and move down to the
desired height.
To Tilt:
• Turn the handle clockwise to tilt the platform up.
• Turn the handle counterclockwise to tilt the platform down.
AA780DAT ARTICULATING KEYBOARD ARM
800.833.3746 esiergo.com
© 2017 ESI Ergonomic Solutions. All rights reserved. AA780DAT Rev A 4/17
Table of contents
Other ESI Rack & Stand manuals
ESI
ESI Kata EX2-FMS User manual
ESI
ESI Kata EX2-MS Series User manual
ESI
ESI AA750DAT Operating and maintenance manual
ESI
ESI AA100 Quick start guide
ESI
ESI LTH-EDGE User manual
ESI
ESI Solution 6CC Quick start guide
ESI
ESI CLIMB2 User manual
ESI
ESI EVOLVE Series User manual
ESI
ESI EVOLVE Series Installation instructions
ESI
ESI Kata Series User manual
Popular Rack & Stand manuals by other brands
Salamander
Salamander Acadia AC/W/L400/WH Assembly instructions
Fohhn
Fohhn VAT-09 Mounting instruction
ricoo
ricoo FS0522 quick start guide
AMSOIL
AMSOIL BMK-22 Installation and service instructions
Kargo Master
Kargo Master 48220 installation guide
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 installation instructions
