ESCO Technologies ETS LINDGREN 3810/2NM User manual
Line Impedance
Stabilization Network
(LISN)
Model 3810/2
User Manual
ii |
ETS-Lindgren L.P. reserves the right to make changes to any product described
herein in order to improve function, design, or for any other reason. Nothing
contained herein shall constitute ETS-Lindgren L.P. assuming any liability
whatsoever arising out of the application or use of any product or circuit
described herein. ETS-Lindgren L.P. does not convey any license under its
patent rights or the rights of others.
© Copyright 1996–2010 by ETS-Lindgren L.P. All Rights Reserved. No part
of this document may be copied by any means without written permission
from ETS-Lindgren L.P.
Trademarks used in this document: The ETS-Lindgren logo is a trademark of
ETS-Lindgren L.P.
Revision Record | MANUAL 3810/2 | Part #399197, Rev. D
Revision Description Date
A–C •Initial Release
•Edits/updates
•Edits/updates
February, 1996
D Rebrand; added EC Declaration of
Conformity
July, 2010
| iii
Table of Contents
Notes, Cautions, and Warnings................................................v
Safety Symbol Definitions.........................................................v
1.0 Introduction..........................................................................7
ETS-Lindgren Product Information Bulletin ...................................................7
2.0 Maintenance.........................................................................9
Service Procedures .....................................................................................10
3.0 Specifications.....................................................................11
Electrical Specifications ...............................................................................11
Physical Specifications ................................................................................12
4.0 Installation and Application..............................................13
Front Panel Connectors and Controls .........................................................15
BNC Connector....................................................................................15
Line Select Switch ...............................................................................15
RF Ground ...........................................................................................15
Earth Line Choke Switch .....................................................................16
AC Receptacle.....................................................................................16
Artificial Hand.......................................................................................16
Back Panel Connectors ...............................................................................17
Power Input..........................................................................................17
RF Ground ...........................................................................................17
5.0 Data .....................................................................................19
6.0 Schematic...........................................................................21
Appendix A: Warranty.............................................................23
Appendix B: EC Declaration of Conformity ..........................25
iv |
This page intentionally left blank.
| v
Notes, Cautions, and Warnings
Note: Denotes helpful information intended to
provide tips for better use of the product.
Caution: Denotes a hazard. Failure to follow
instructions could result in minor personal injury
and/or property damage. Included text gives proper
procedures.
Warning: Denotes a hazard. Failure to follow
instructions could result in SEVERE personal injury
and/or property damage. Included text gives proper
procedures.
See the ETS-Lindgren Product Information Bulletin for safety,
regulatory, and other product marking information.
Safety Symbol Definitions
EQUIPOTENTIALITY
Identifies the terminals, when connected together,
to bring various parts of a system to the same
potential, not necessarily being the earth (ground)
potential, e.g. for local bonding.
See the ETS-Lindgren Product Information Bulletin for safety,
regulatory, and other product marking information.
vi |
This page intentionally left blank.
Introduction | 7
1.0 Introduction
See the ETS-Lindgren Product Information Bulletin included with your shipment
for the following:
The Model 3810/2 was designed and tested in accordance with
IEC Publication 1010, Safety Requirements for Electronic Measuring
Apparatus, and is supplied in a safe condition.
The conducted emissions measurements may be made in accordance with
regulatory compliance standards
Model 3810/2 Front View
•Safety, regulatory, and other product marking information
ETS-Lindgren Product Information Bulletin
•Steps to return a component for service
•ETS-Lindgren contact information
•ETS-Lindgren calibration service
•Steps to receive your shipment
•Warranty information
The ETS-Lindgren
Model 3810/2 Line
Impedance Stabilization
Network (LISN) is a
two-channel low pass filter
network designed to isolate
the Equipment Under Test
from an external power
source while steering any
radio frequency signals
from the power line to a
50-ohm port.
8 | Introduction
This page intentionally left blank.
Maintenance | 9
2.0 Maintenance
Before Servicing contact ETS-Lindgren.
Servicing (or modifying) the unit yourself
may void your warranty. If you attempt to
service the unit yourself, disconnect all
electrical power before starting. There are
voltages at many points in the instrument
which could, if contacted, cause personal
injury. Only trained service personnel
should perform adjustments and/or
service procedures upon this instrument.
Before performing any maintenance,
follow the safety information in the
ETS-Lindgren Product Information
Bulletin included with your shipment.
Inside the Model 3810/2 are LETHAL
voltages with which you could come into
contact. Capacitors inside the unit may
still be CHARGED even when the unit is
disconnected from power.
Only trained service personnel should
perform adjustments and/or service
procedures.
WARRANTY
10 | Maintenance
For the steps to return a system or system component to ETS-Lindgren for
service, see the Product Information Bulletin included with your shipment.
Clean the exterior of the cabinet using a
damp cloth and mild cleaner. Always
unplug the unit before cleaning.
Maintenance of the Model 3810/2 is
limited to external components such as
cables or connectors.
If you have any questions concerning
maintenance, contact ETS-Lindgren
Customer Service.
To prevent electrical shock, do not
remove cover.
Service Procedures
This manual suits for next models
3
Table of contents
