ESCALADE Atomic G01342W User manual

888-996-2729-1

1353-378-668-1:XAF

moc.stropsedalacse@gameroom

ytilauqtsehgihehtfoerastcudorpruotahterusneotevirtseW

fi,revewoH.strapgnissimrostcefedgnirutcafunamfoe

erfdna

,tcudorpwenruoyhtiwsmelborpynaevahuoy

EROTSEHTOTTINRUTERTONOD ,

:@eerfllotsutcatnocesaelp

:otetirwrO

stropSedalacsE

tnemtrapeDecivreSremotsuC

988xoB.O.P

60774NI,ellivsnavE

date code (if,rebmunledomruoyedivorpesaelpstropSedalacsEgnitcatnocnehW

erasrebmunesehT.traptnemecalp

eragnitseuqerfirebmuntrapdna,)elbacilppa

.launamsrenwosihtnidna,gnigakcap,tcudorpehtnodetacol

rebmuNledoMruoY

.straptuobagniriuqninehwdate coderuoyevahesaelP

G01342W/F

888-996-2729-1llaCecivreSremotsuCroF1stropSedalacsE2016©

Date Code: 2 - G01342W/F - 0416 - WJ

Purchase Date:

PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE

Make sure you understand the following tips before you begin to assemble your soccer table.

1. Start all bolts by hand before tightening.

2. Some drawings or images in this manual may not look exactly like your product. Please

read and understand the text before starting each assembly step.

TWO ADULTS ARE REQUIRED TO ASSEMBLE

THIS ATOMIC PROFORCE SOCCER TABLE

Assembly Tips

Tools Required:

READ AND FOLLOW ALL ASSEMBLY, OPERATION, AND

SAFETY INSTRUCTIONS CAREFULLY. AT LEAST TWO

ADULTS ARE NEEDED TO PUT THIS SOCCER TABLE

TOGETHER.

T1 - Allen Wrench (Included)

IMPORTANT! READ EACH STEP

IN THIS MANUAL BEFORE YOU

BEGIN THE ASSEMBLY.

Phillips Screwdriver

Furniture Polish and Cloth

HARDWARE IDENTIFIER

( To Scale)

H1 - 6mm x 22mm

Allen Head Bolt

(16 pcs)

H2 - 6mm x 19mm

Flat Washer (16 pcs)

H3 - 3mm x 28mm

Phillips Flat Head

Screw (8 pcs)

H4 - 4mm x 12mm

Phillips Round Head

Screw (84 pcs)

H5 - 3mm x 28mm

Phillips Washer Head

Screw (18 pcs)

(Not to Scale)

H6 - 4mm x 12mm

Phillips Flat Head

Screw (6 pcs)

H7 - 4mm x 51mm

Phillips Flat Head

Screw (12 pcs)

H8 - 4mm x 51mm

Zinc - Phillips Flat Head

Screw (4 pcs)

T1 - Allen Wrench

(1 pc)

ACCESSORIES IDENTIFIER

( Not to Scale)

A1- Soccer Ball (4 pcs)

!WARNING:

CHOKING HAZARD

Small parts.

Not for children under 3 yrs.

PARTS IDENTIFIER

( Not to Scale)

P1 - Side Apron

(2 pcs)

P2 - End Apron

(2 pcs)

P3 - Leg (4 pcs)

P5 - End Top Rail

(2 pcs)

P6 - Goal End

Board (2 pcs)

P4 - Playfield (1 pc)

P7 - Playfield Support

Brace (2 pcs)

P8 - Top Goal

Box (2 pcs)

P9 - Bottom Goal

Box (2 pcs)

P10 - Scorer (2 pcs) P11 - Leg Leveler

(4 pcs)

P12 - Playfield

Trim (2 pcs)

P13 - Plastic Rod

Washer (16 pcs)

P14 - Rod Bumper

(16 pcs)

P15 - Rod End

Cap (8 pcs)

P16 - Rod Handle

(8 pcs)

P17 - Outside Ball

Entry Cup (2 pcs)

!WARNING:

CHOKING HAZARD

Small parts.

Not for children under

3 yrs.

P18 - Plastic

Bracket (18 pcs)

ROD IDENTIFIER

( Not to Scale)

!WARNING:

CHOKING HAZARD

Small parts.

Not for children under

3 yrs.

R1 - 2 Player Rod

Assembly Black (1 pc)

R2 - 3 Player Rod

Assembly Black (2 pcs)

R3 - 5 Player Rod

Assembly Black (1 pc)

R4 - 2 Player Rod

Assembly Ivory (1 pc)

R5 - 3 Player Rod

Assembly Ivory (2 pcs)

R6 - 5 Player Rod

Assembly Ivory (1 pc)

STEP 1:

Find a clean, level place to begin the assembly of your soccer table. We recommend building the table on the

box top to protect the parts during assembly.

Attach P13 Plastic Rod Washer and P14 Rod Bumper to the rods as shown in FIGURE 1. Place one P1 Side

Apron UPSIDE DOWN with the laminated side facing out as shown in FIGURE 1.

Align the rods as shown in FIGURE 1.

Please note the location of the hole that is near one end of each rod. This is the handle end of the rod.

There will be four handles on each side of the table. It is critical that you set the rods as shown below so

the table will be correct when flipped over.

PARTS REQUIRED:

1 pc - P1 Side Apron 1 pc - R1 2 Player Rod Assembly Black 1 pc - R4 2 Player Rod Assembly Ivory

16 pcs - P13 Plastic Rod Washer 2 pcs - R2 3 Player Rod Assembly Black 2 pcs - R5 3 Player Rod Assembly Ivory

16 pcs - P14 Rod Bumper 1 pc - R3 5 Player Rod Assembly Black 1 pc - R6 5 Player Rod Assembly Ivory

FIGURE 1

P14

P13

P14

R1, R2 and R3

Hole/Handle End

R4, R5 and R6

Hole/Handle

goes on the

other end of

these rods

C1 Rod Bushing

Note: C1 Rod Bushings

are already attached

onto P1 Side Apron

STEP 2:

Once your are sure you have the rods set

correctly, slide the other P1 Side Apron on

the rods as shown in FIGURE 2.

PARTS REQUIRED:

1 pc - P1 Side Apron

FIGURE 2

R1, R2 and R3

Hole/Handle End

R4, R5 and R6

Hole/Handle

goes on the

other end of

these rods

C1 Rod Bushing

Note: C1 Rod Bushings

are already attached

onto P1 Side Apron

PARTS REQUIRED:

16 pcs - H4 Phillips Round Head Screw

2 pcs - P5 End Top Rail

2 pcs - P6 Goal End Board

4 pcs - P18 Plastic Bracket

STEP 3:

Place two P18 Plastic Brackets onto each inside

end of P6 Goal End Board as shown and attach

using the pre-drilled pilot holes with H4 Screws

as shown in FIGURE 3A.

Tighten, but do not strip out H4 screws.

NOTE: Be sure bottom edge of P18 Plastic

Brackets is flush with bottom edge of board.

Next, attach this assembly to P5 End Top Rail

using pre-drilled pilot holes with H4 Screws as

shown in FIGURE 3B.

Tighten, but do not strip out H4 screws.

NOTE: Be sure bottom edge of P6 Goal End

Board is flush with bottom edge of P5 Top Rail.

Repeat procedure for second assembly.

White laminate

this side

P18

FIGURE 3A

Black laminate

on bottom side

Round Corner

this position

FIGURE 3B

Edge must be

flush for correct

assembly

Edge must be

flush for correct

assembly

NOTE: See STEP 4 to look at

correct assembly P5 and P6.

STEP 4:

Attach P5/P6 assemblies from STEP 3 to P1 Side Apron using pre-drilled pilot holes with H3 Screws as shown

in FIGURE 4. Tighten, but do not strip out H3 Screws.

IMPORTANT NOTE: The holes are pre-drilled at an ANGLE on purpose, be sure to allow H3 Screws to follow

pre-drilled holes.

PARTS REQUIRED:

8 pcs - H3 Phillips Flat Head Screw

FIGURE 4

P5/P6

Assembly

P5/P6

Assembly H3 P1

STEP 5:

Install one piece P18 Plastic Bracket

into each inside corner of P1 Side Apron

using pre-drilled pilot holes and H4

screws as per FIGURE 5 and DETAIL A.

Tighten, but do not strip out H4 screws.

PARTS REQUIRED:

16 pcs - H4 Phillips Round Head Screw

4 pcs - P18 Plastic Bracket

P18

DETAIL A

FIGURE 5

IMPORTANT NOTE:

Be sure to keep this assembly

square during P5/P6 assembly.

STEP 6:

Carefully peel the protective film strips off of the 3 pieces of adhesive tape on the underside of both P12 Playfield

Trims. Turn them over and carefully place them along P1 Side Aprons as shown in DETAIL B and FIGURE 6.

PARTS REQUIRED:

2 pcs - P12 Playfield Trim

FIGURE 6

DETAIL B

Peel and Turn Over

STEP 7:

Place P4 Playfield with graphics

facing down onto the main cabinet.

Align P4 Playfield holes with P12

Playfield Trims holes and attach

using H5 Screws as shown in

FIGURE 7.

Tighten, but do not strip out H5

Screws.

PARTS REQUIRED:

18 pcs - H5 Phillips Washer

Head Screw

1 pc - P4 Playfield

P12

FIGURE 7

Graphic

facing down

IMPORTANT NOTE:

P4 Playfield must be evenly

spaced on top of both ends

of P6 Goal End Board - at each

end of cabinet assembly.

P1 Side Aprons may be slightly

warped. Please keep P1 Side

Aprons pushed in tight against

the P4 Playfield for correct assembly.

All screws must be screwed

STRAIGHT down.

NOTE: Adhesive

strip this side.

STEP 8:

Attach P18 Plastic Brackets onto the back side

of P2 End Apron using pre-drilled pilot holes

with H4 Screws as shown in FIGURE 8.

Tighten, but do not strip out H4 screws.

NOTE: Be sure bottom edge of P18 Plastic

Brackets is flush with bottom edge of apron.

Attach P8 Top Goal Box and P9 Bottom Goal

Box onto the back side of P2 End Apron using

pre-drilled holes with H4 Screws as shown in

FIGURE 8.

Tighten, but do not strip out H4 screws.

Repeat procedure for second assembly.

PARTS REQUIRED:

20 pcs - H4 Phillips Round Head Screw 2 pcs - P8 Top Goal Box 4 pcs - P18 Plastic Bracket

2 pcs - P2 End Apron 2 pcs - P9 Bottom Goal Box

FIGURE 8

P18

STEP 9:

Attach previous assemblies from STEP 8 to the end of table cabinet using pre-drilled pilot holes with H7 Screws

as shown in FIGURE 9. Tighten, but do not strip out H7 screws.

Install H4 Screws into previously installed P18 Plastic Brackets as shown in FIGURE 9.

Tighten, but do not strip out H4 screws.

PARTS REQUIRED:

8 pcs - H4 Phillips Round Head Screw

12 pcs - H7 Phillips Flat Head Screw

H7 STEP 8

Assembly

STEP 8

Assembly

P18

FIGURE 9

NOTE:

Ball Opening

in P2 End Apron

must be in this

position.

NOTE:

Opening of P9 Bottom Goal

Box must be in this position.

This manual suits for next models

Table of contents

Languages:

Other ESCALADE Game manuals

ESCALADE

ESCALADE Triumph 35-7052-2 User manual

ESCALADE

ESCALADE Atomic G01344W User manual

ESCALADE

ESCALADE Triumph User manual

ESCALADE

ESCALADE Triumph 35-7077 User manual

ESCALADE

ESCALADE Viva Sol User manual

ESCALADE

ESCALADE ping-pong T8466F User manual

ESCALADE

ESCALADE Triumph 45-6747 User manual

ESCALADE

ESCALADE G07611 User manual

ESCALADE

ESCALADE Mizerak P0900 User manual

ESCALADE

ESCALADE Triumph Hyperloop User manual

Popular Game manuals by other brands

Outdoor Play

Outdoor Play Box it! 2020 instruction manual

Beleduc

Beleduc Papilio Instruction

Costway

Costway UY10001 user manual

Vex

Vex Add It Up Assebly instructions

DGT

DGT Centaur manual

Radica Games

Radica Games BUCKAROO 630 instruction manual

Fundex Games

Fundex Games Timber Tumble User instructions

Go! Gater

Go! Gater 1-1-16453-TP02 Assembly instructions

Smoby

Smoby BBF Challenger quick start guide

Hathaway

Hathaway BG2019SK Assembly instructions

Roberto Sport

Roberto Sport INGLESE Assembly instructions

Beleduc

Beleduc XXL Witches' Kitchen Instruction

Koala Technologies

Koala Technologies KoalaWare Spider Eater owner's manual

Tomy

Tomy The Magic Oven manual

Sega

Sega GAME SHOW owner's manual

Tiger Electronics

Tiger Electronics Last Out 7-584-0 instructions

Fisher-Price

Fisher-Price RollOverRover manual

Mattel

Mattel World Championship Football instructions