ESAB RS 400 User manual

RS 400 / RS 400 with ESU

Thyristorised MMA

Welding Power Source

Instruction manual

RS 400 / RS 400 with ESU

THYRISTORISED MMA WELDING POWER SOURCE

Instruction manual

For

Installation, Operation & General maintenance

CONTENTS

Item Page No.

SAFETY

1-2

ASSEMBLING 3

ACCESSORIES LIST 3

RATING 3

CAUTIONS FOR INSTALLATION 3-4

ITEMS FOR INSTALLATION 4

WELDING OPERATIONS 5

WORKING PRINCIPLES OF ESU UNIT 6

(IN MACHINES FITTED WITH ESU)

MAINTENANCE & INSPECTION 6-7

AFTER SALES SERVICE 7

FAULT FINDING 8-9

WIRING DIAGRAM RS 400 (STANDARD) 10

WIRING DIAGRAM RS 400 WITH ESU 11

TEST POINT VOLTAGES IN CONTROL PCB 12

SPARES IDENTIFICATION – RS 400

13 - 16

RECOMMENDED LIST OF SPARES – RS 400 17

SAFETY

Users of ESAB welding equipment have the ultimate responsibility for ensuring that

anyone who works on or near the equipment observes all the relevant safety

precautions. Safety precautions must meet the requirements that apply to this type of

welding equipment. The following recommendations should be observed in addition to

the standard regulations that apply to the workplace.

Trained personnel well acquainted with the operation of the welding equipment must

carry out all the work. Incorrect operation of the equipment may lead to hazardous

situations, which can result in injury to the operator and damage to the equipment.

1. Anyone who uses the welding equipment must be familiar with:

• its operation

• location of emergency stops

• its function

• relevant safety precautions

• welding

2. The operator must ensure that:

• no unauthorized person is stationed within the working area of the equipment

when it is started up.

• no one is unprotected when the arc is struck

3. The workplace must:

• be suitable for the purpose

• be free from drafts

4. Personal safety equipment

• Always wear recommended personal safety equipment, such as safety glasses,

flameproof clothing, and safety gloves.

• Do not wear loose—fitting items, such as scarves, bracelets, rings, etc., which

could become trapped or cause burns.

5. General precautions

• Make sure the return cable is connected securely.

• Only a qualified electrician may carry out work on high voltage equipment.

• Appropriate fire extinguishing equipment must be clearly marked and close at

hand.

• Lubrication and maintenance must not be carried out on the equipment during

operation.

Read and understand the instruction manual before installing or operating.

ESAB can provide you with all necessary welding protection and accessories.

WARNING

Arc welding and cutting can be injurious to yourself and others. Take

precautions when welding.

Ask for your employer’s safety practices which should be based on manufacturers’

hazard data.

ELECTRIC SHOCK – Can kill

• Install and earth the welding unit in accordance with applicable

standards.

• Do not touch live electrical parts or electrodes with bare skin, wet

gloves or wet clothing.

• Insulate yourself from earth and the workpiece.

• Ensure your working stance is safe.

FUMES AND GASES – Can be dangerous to health

• Keep your head out of the fumes.

• Use ventilation, extraction at the arc, or both, to take fumes and gases

away from your breathing zone and the general area.

ARC RAYS – Can injure eyes and burn skin.

• Protect your eyes and body. Use the correct welding screen and filter

lens and wear protective clothing.

• Protect bystanders with suitable screens or curtains.

FIRE HAZARD

• Sparks (spatter) can cause fire. Make sure therefore that there are no

inflammable materials nearby.

NOISE – Excessive noise can damage hearing

• Protect your ears. Use earmuffs or other hearing protection.

• Warn bystanders of the risk.

MALFUNCTION – Call for expert assistance in the event of malfunction.

PROTECT YOURSELF AND OTHERS!

CAUTION!

This product is solely intended for arc welding

Do not dispose of electrical equipment together with normal waste!

In accordance with national law, electrical equipment that has

reached the end of its life must be collected separately and returned

to an environmentally compatible recycling facility. As the owner of

the equipment, you should get information on approved collection

systems from the local representative. By applying this Directive you

will improve the environment and human health

ASSEMBLLING

The complete installation should consist the following items:

Description Type Quantity

1. Welding Power Source RS 400 Power

Source 1

2. Remote Controller

(Optional) RCU RS-400 1

ACCESSORIES LIST FOR THYRISTORISED WELDING RECTIFIER RS 400

Fuse, element 1A 1 piece

Instruction Manual 1 piece

RATING OF RS 400 THYRISTORISED MMA WELDING POWER SOURCE

CHARACTERISTICS CONSTANT CURRENT TYPE

Input:

SUPPLY VOLTAGE, PHASE & FREQUENCY 415± 10%, 3 Phases, 50 Hz, AC

RATED INPUT CURRENT 27 A

RATED RATING 19.4 KVA

Output:

OUTPUT CURRENT RANGE DC 10-400A (Single Range)

OPEN CIRCUIT VOLTAGE (NOMINAL) 95 V DC

TYPE OF WELDING CURRENT CONTROL STEPLESS

CLASS OF INSULATION ‘H’

COOLING FORCED AIR COOLED

APPROX DIMENSION (LxWxH) IN MM 825 x 695 x 1070

WEIGHT (APPROX) 195 KG.

CAUTIONS FOR INSTALLATION

a) Capacity of Equipment

Input Voltage AC 415 V 10%

Number of Phase &

Frequency 3 phases, 50 Hz

Capacity of Fuse (B Class)

63 Amps

Input Cable More than 10 mm2

Output Cable More than 50 mm2

 Provide a Switch Box for every Welding Power Source, and use designated

fuse

 Tolerance of Power Voltage Variation is 10% of rated input voltage.

 100 Amps MCB to be used as alternative to SFU.

a) Installation place

 Install in the place where less moisture and dust exist. Avoid direct sunlight and

rain, and maintain ambient temperature within –10o to +45o C as much as

possible.

 Keep the welding power source at least 20 cm. away from the wall (if any).

 In case of installation of more two units side by side, a distance of more than 20

cm is recommended between the two power sources.

 Use a shield to protect the welding arc in case of excessive air draft.

c) Ventilation

Adequate ventilation is recommended at the place of installation. For

example the following guideline should be followed:

a) In case of the area being more than 300 square meters (per unit), no

ventilation is required, provided the room is not completely airtight.

b) In case of the area being less than 300 square meters and the welding

is continuously performed, adequate ventilation is recommended with

the help of vent fan or exhaust duct.

c) While performing the grounding work, it is recommended that a skilled

electrician does the work.

ITEMS FOR INSTALLATION

No. Item No.

Item

1. Remote Control Unit RS 400

(Optional) 8. Welding cable

2. Work Piece 9. Welding cable

3. Switch Box (Input) 10. Input Cable

4. Connector for Remote Control Unit 11. Electrode Holder

5. Negative Terminal 12. Electrode

6. Positive Terminal 13. Terminal Block input

7. Control Cable for RCU RS 400 14. ON OFF Switch

WELDING OPERATION

Once the installation of the equipment is completed, connect the work Cable to

the negative output terminal and the cable end of the electrode holder to the

Positive output terminal. These cable connections should be tightened properly

to avoid electrical heating due to loose connections. Put the main Switch box in

‘ON’. Turn on “Power ON/OFF switch” on the rear panel. The green lamp on

the panel of the Power Source will glow and the fan will start rotating. Now the

equipment is ready. Connect an Electrode with the Electrode Holder. The

welding current can be controlled by the current control potentiometer mounted

on the front panel of the Power source or through Remote Controller as

explained below.

Welding Current Adjustment

Put the “Local / Remote” switch to ‘Local’ mode. Now set the DC output current

as required with the help of the current control potentiometer and ignite an

experimental Arc. For the fine-tuning of the required current, set the parameters

using the Ammeter mounted on the front panel of the power source.

Load Voltage / Open Circuit Voltage

Operate the “Amps/Volts” switch to Volts position; the meter on the front panel

will now indicate the output DC voltage. On releasing this switch, it will

automatically come back to Amps position and the meter will read the output

DC welding current.

Remote Controller

The output Welding current can be increased and decreased as desired from

the operation point with the help of the Remote Controller unit as per the

following guideline, even on load condition.

Set the Local/Remote switch to remote position and connect the remote

controller to the socket provided in the power source. Now set the Welding

current by turning current control potentiometer. Graduation of the current value

mentioned on the Remote Controller Unit should be followed as guideline.

However, for accurate output current, adjust the potentiometer to a proper

value from the METER, mounted on the Front panel of the power source after

generating an experimental arc.

Welding with Cellulosic Electrode

 Put Normal/Cellulosic Switch to Cellulosic Position depending on the

size of the electrode.

 Keep the main potentiometer around the middle position of the scale &

do the welding.

Working Principle of Energy Saving Unit:

Energy Saving Circuit is an optional feature in the RS 400 Machine. Working

principle of the ESU is explained below:

The extra items fitted in RS 400 having the Energy Saving feature comprises of:

a) Control Transformer for ESU

b) Control PCB for ESU

c) Line Contactor- ESU

The unit, when energized provides an auxiliary low 55-60 VD.C to the output of the

main Welding Rectifier.

On attempting to strike the welding arc, the output is sensed by the PCB, which

triggers on the coil of the main line contactor. The contactor (3 pole) provides the 3-

phase A.C supply to the welding machine.

The machine is enabled, and welding can be done as usual. The contactor stays ON

throughout the welding period by current sensing circuit (provided by Hall Sensor in

the Machine)

When the welding is stopped, the output of the rectifier reaches the O.C.V of the

machine (about 100 V D.C). The PCB senses this and the disables the main contactor

to switch off the supply to the Machine, and once again the low voltage of 55-60 V DC

appears across the welding terminals, which is a low safe voltage.

In the no-weld condition, the line contactor remains disabled, and the Main

Transformer also remains unconnected, thereby reducing the no-load losses of the

machine to a very low value

MAINTENANCE & INSPECTION

The maintenance and inspection should be carried out only after the switches

in the Main switch box certainly turned OFF.

Try to maintain and inspect the set regularly as per the following guide lines.

a) Regular Inspection

Every 3-6 months, depending on operation frequency:

Inspection Portion Inspection Point Maintenance Method

Fuse Box Fastening & Looseness

at the Connection.

Confirmation of proper

fuse

Refer to the Equipment

capacity

Input and Output

Connections Fastening & Looseness

at the Connection.

Confirmation of

Installation

Faster first and Tape

Interior of Welding

Power Source Sedimentation of Dust.

Trace of Overheat. Blow off dust with

Compressed Air.

b) Cautions to Insulation Voltage – Proof Test & Insulation Resistance

Measurement Test:

Careless execution of Dielectric Strength test and Insulation Resistance

Measurement will cause damage to the power source since thyristors,

transistors and other semiconductor parts are used in the unit. While

conducting these tests in accordance with the by-laws of your company, the

following steps should be performed first: -

 Take of the cables from the switch box that are connected to the three

input terminals and short circuit the three input terminals.

 Take off the cable that is connected to two output terminals and short

circuit the two output terminals.

 Short circuit between positive and negative output of Rectifier bank with

three AC terminals of rectifier bank.

 Use 500 V Megger only.

 Go back to original conditions removing short-circuit etc. once the test is

over.

AFTER SALES SERVICE

In case of any abnormality observed during usage of the equipment,

which could not be rectified at site, please contact immediately Area

Sales Manager of the nearest unit of ESAB INDIA LIMITED with the

following details:

1) Serial Number of the equipment & type

2) Nature of the complaint with the relevant details, if possible and the

details of Input Supply.

3) Date of purchase of the equipment and the date of commissioning.

The qualified and trained service teams of ESAB INDIA LIMITED,

located of the zonal head quarters render the after sales service to the

customers and also assist in intelligent selections of Welding Equipment

& consumable for various applications.

This manual suits for next models

Table of contents

Other ESAB Welding System manuals

ESAB

ESAB LKA 180 User manual

ESAB

ESAB Mig 4004i User manual

ESAB

ESAB Aristo Mig 5000i 400 V User manual

ESAB

ESAB Rogue EMP 210 PRO User manual

ESAB

ESAB Tig 4000i Aristo User manual

ESAB

ESAB OCF 2L User manual

ESAB

ESAB Origo Mig 4002c User manual

ESAB

ESAB Origo Tig 3001i User manual

ESAB

ESAB LPH 80 User manual

ESAB

ESAB ORIGO Mig C280 PRO User manual

ESAB

ESAB Precision Plasmarc EPP-600 User manual

ESAB

ESAB Aristo 300 User manual

ESAB

ESAB LTH 161 User manual

ESAB

ESAB A2 Multitrac User manual

ESAB

ESAB Railtrac B42V User manual

ESAB

ESAB Jesse James SIGNATURE Series User manual

ESAB

ESAB Retrofit Aristo Mig 4004i WeldCloud User manual

ESAB

ESAB Rustler EM 280C PRO User manual

ESAB

ESAB Firepower MST-200 User manual

ESAB

ESAB Miniarc 150 User manual

ESAB

ESAB SR-B 9 User manual

ESAB

ESAB LHF 250 User manual

ESAB

ESAB ESP-150 User manual

ESAB

ESAB LAF 800 DC User manual

Popular Welding System manuals by other brands

Berner

Berner PLASMACUT 54 instruction manual

Pro Spot

Pro Spot PR-155 Assembly instructions

Forney

Forney 210 operating manual

Thermal Arc

Thermal Arc 400S operating manual

Lincoln Electric

Lincoln Electric HANDYMIG 170I Operator's manual

GYS

GYS PROTIG 201 AC/DC Original instructions

TAFA

TAFA 30*8B35 owner's manual

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Technical specifications

CIGWELD

CIGWELD 636804 use instructions

Red-D-Arc

Red-D-Arc DC-400 Operator's manual

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 owner's manual

Elettro

Elettro HI-MIG 3000 SYNERGIC instruction manual

WIA

WIA Weldmatic 270 CP132-2 Operator's manual

Sonics

Sonics H520T instruction manual

Miller

Miller Big Blue 400D owner's manual

NewArc

NewArc RT2000 Operational manual

Hypertherm

Hypertherm powermax1000 Operator's manual

Lincoln Electric

Lincoln Electric POWER WAVE I400 Operator's manual