ESAB Aristo W82 User manual

Aristo®

Instruction manual

0460 971 301 GB 20161014

Valid for: W82 serial no. 544-, 628-xxx-xxxx

RetrofitMig4004iWeldCloud™serialno.550-xxx-xxxx

W82,

RetrofitMig4004iWeldCloud™

TABLE OF CONTENTS

0460 971 301 © ESAB AB 2016

1SAFETY ........................................................................................................... 4

1.1 Meaning of symbols ...................................................................................... 4

1.2 Safety precautions ........................................................................................ 4

2INTRODUCTION.............................................................................................. 7

2.1 Equipment...................................................................................................... 7

3TECHNICAL DATA .......................................................................................... 8

4INSTALLATION................................................................................................ 9

4.1 Assembly instruction .................................................................................... 9

4.2 System description ....................................................................................... 9

4.3 How to set-up the U82 for use with W82 ..................................................... 10

4.3.1 Save your stored data ................................................................................. 10

4.3.2 Convert the U82 stand alone unit to a presentation unit ............................. 10

4.4 System diagrams........................................................................................... 11

5OPERATION .................................................................................................... 13

5.1 Connections and control devices ................................................................ 13

5.2 Overheating protection ................................................................................. 14

5.3 Arc voltage feedback .................................................................................... 14

6MAINTENANCE............................................................................................... 16

6.1 Inspection and cleaning................................................................................ 16

7ORDERING SPARE PARTS ............................................................................ 17

DIAGRAM ............................................................................................................... 18

ORDERING NUMBERS.......................................................................................... 21

ACCESSORIES ...................................................................................................... 22

Rights reserved to alter specifications without notice.

1 SAFETY

0460 971 301 -4- © ESAB AB 2016

1 SAFETY

1.1 Meaning of symbols

As used throughout this manual: Means Attention! Be Alert!

DANGER!

Means immediate hazards which, if not avoided, will result in immediate,

serious personal injury or loss of life.

WARNING!

Means potential hazards which could result in personal injury or loss of

life.

CAUTION!

Means hazards which could result in minor personal injury.

WARNING!

Before use, read and understand the instruction manual

and follow all labels, employer´s safety practices and

Material Safety Data Sheets (MSDSs).

1.2 Safety precautions

NOTE!

The unit is tested by ESAB in a general set-up. The responsibility for safety and

function, of the specific set-up, lies with the integrator.

Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who

works on or near the equipment observes all the relevant safety precautions. Safety

precautions must meet the requirements that apply to this type of equipment. The following

recommendations should be observed in addition to the standard regulations that apply to

the workplace.

All work must be carried out by trained personnel well-acquainted with the operation of the

equipment. Incorrect operation of the equipment may lead to hazardous situations which can

result in injury to the operator and damage to the equipment.

1. Anyone who uses the equipment must be familiar with:

○ its operation

○ location of emergency stops

○ its function

○ relevant safety precautions

○ welding and cutting or other applicable operation of the equipment

2. The operator must ensure that:

○ no unauthorised person is stationed within the working area of the equipment

when it is started up

○ no-one is unprotected when the arc is struck or work is started with the equipment

3. The workplace must:

○ be suitable for the purpose

○ be free from drafts

1 SAFETY

0460 971 301 -5- © ESAB AB 2016

4. Personal safety equipment:

○ Always wear recommended personal safety equipment, such as safety glasses,

flame-proof clothing, safety gloves

○ Do not wear loose-fitting items, such as scarves, bracelets, rings, etc., which

could become trapped or cause burns

5. General precautions:

○ Make sure the return cable is connected securely

○ Work on high voltage equipment may only be carried out by a qualified

electrician

○ Appropriate fire extinguishing equipment must be clearly marked and close at

hand

○ Lubrication and maintenance must not be carried out on the equipment during

operation

WARNING!

Arc welding and cutting can be injurious to yourself and others. Take precautions

when welding and cutting.

ELECTRIC SHOCK - Can kill

• Install and ground the unit in accordance with instruction manual.

• Do not touch live electrical parts or electrodes with bare skin, wet gloves or

wet clothing.

• Insulate yourself from work and ground.

• Ensure your working position is safe

ELECTRIC AND MAGNETIC FIELDS - Can be dangerous to health

• Welders having pacemakers should consult their physician before welding.

EMF may interfere with some pacemakers.

• Exposure to EMF may have other health effects which are unknown.

• Welders should use the following procedures to minimize exposure to EMF:

○ Route the electrode and work cables together on the same side of your

body. Secure them with tape when possible. Do not place your body

between the torch and work cables. Never coil the torch or work cable

around your body. Keep welding power source and cables as far away

from your body as possible.

○ Connect the work cable to the workpiece as close as possible to the

area being welded.

FUMES AND GASES - Can be dangerous to health

• Keep your head out of the fumes.

• Use ventilation, extraction at the arc, or both, to take fumes and gases

away from your breathing zone and the general area.

ARC RAYS - Can injure eyes and burn skin

• Protect your eyes and body. Use the correct welding screen and filter lens

and wear protective clothing.

• Protect bystanders with suitable screens or curtains.

NOISE - Excessive noise can damage hearing

Protect your ears. Use earmuffs or other hearing protection.

1 SAFETY

0460 971 301 -6- © ESAB AB 2016

MOVING PARTS - Can cause injuries

• Keep all doors, panels and covers closed and securely in place. Have only

qualified people remove covers for maintenance and troubleshooting as

necessary. Reinstall panels or covers and close doors when service is

finished and before starting engine.

• Stop engine before installing or connecting unit.

• Keep hands, hair, loose clothing and tools away from moving parts.

FIRE HAZARD

• Sparks (spatter) can cause fire. Make sure that there are no inflammable

materials nearby.

• Do not use on closed containers.

MALFUNCTION - Call for expert assistance in the event of malfunction.

PROTECT YOURSELF AND OTHERS!

CAUTION!

This product is solely intended for arc welding.

WARNING!

Do not use the power source for thawing frozen pipes.

CAUTION!

Class A equipment is not intended for use in residential

locations where the electrical power is provided by the

public low-voltage supply system. There may be potential

difficulties in ensuring electromagnetic compatibility of class

A equipment in those locations, due to conducted as well

as radiated disturbances.

NOTE!

Dispose of electronic equipment at the recycling

facility!

In observance of European Directive 2012/19/EC on Waste

Electrical and Electronic Equipment and its implementation

in accordance with national law, electrical and/or electronic

equipment that has reached the end of its life must be

disposed of at a recycling facility.

As the person responsible for the equipment, it is your

responsibility to obtain information on approved collection

stations.

For further information contact the nearest ESAB dealer.

ESAB can provide you with all necessary welding protection and accessories.

2 INTRODUCTION

0460 971 301 -7- © ESAB AB 2016

2 INTRODUCTION

Aristo® W82

W82is a control unit that enables communication between welding

equipment and automation equipment, such as robots and

computers. Communication protocols: DeviceNet, Profibus,

CANopen and Ethernet.

W82is used together with ESAB CANbus equipped power sources

for welding automation. For power source and wire feed unit

handling, see the relevant instruction manual.

Retrofit Mig 4004i WeldCloud™

Retrofit Mig 4004i WeldCloud™ is retrofitted on top of supported

ESAB power sources. It connects to the CANbus internally.

Communication protocol: WeldCloud™.

There are two versions of Retrofit Mig 4004i WeldCloud™ available,

with different functionality. The available versions have ordering

numbers 0445302880 (without connection for ethernet and

communication with robot system) and 0445302881 (with

connection for ethernet and communication with robot system).

For information about supported power sources, contact your ESAB

sales representative.



2.1 Equipment



Aristo® W82

• W82DeviceNet, W82Profibus, W82CANopen and W82Ethernet are supplied with a

USB memory and an instruction manual.

• W82Integrated is supplied with an instruction manual.



Retrofit Mig 4004i WeldCloud™

• Retrofit Mig 4004i WeldCloud™ is supplied with the software WeldCloud™ and a

Quick start guide.



Measurement cable kit and connection cables for different power sources are available as

accessories, see "ACCESSORIES" chapter and separate spare parts list.

3 TECHNICAL DATA

0460 971 301 -8- © ESAB AB 2016

3 TECHNICAL DATA

Aristo®W82

Supply voltage (to feed unit through W82)42 V, 50-60 Hz

Supply voltage (from robot) 24 V DC

Supply voltage (from power source) 12 V DC

Weight 4 kg (8.8 lb.)

Dimensions (l × w × h) 366 × 101 × 159 mm (14.41×3.98×6.26in.)

Enclosure class IP23

Retrofit Aristo®Mig 4004i WeldCloud™ (0445 302 880)

Supply voltage (to feed unit through WeldCloud™) 42 V, 50-60 Hz

Supply voltage (from power source) 12 V DC

Weight 6 kg (13.2 lb.)

Dimensions (l × w × h) 527 × 257 × 115 mm

(20.75×10.12×4.52in.)

Enclosure class IP23

Retrofit Aristo®Mig 4004i WeldCloud™ (0445 302 881)

Supply voltage (to feed unit through WeldCloud™) 42 V, 50-60Hz

Supply voltage (from power source) 12 V DC

Weight 6 kg (13.2 lb.)

Dimensions (l × w × h) 527×257×105mm

(20.75×10.12×4.13in.)

Enclosure class IP23

Enclosure class

The IP code indicates the enclosure class, i.e. the degree of protection against penetration

by solid objects or water.

Equipment marked IP23 is intended for indoor and outdoor use.

4 INSTALLATION

0460 971 301 -9- © ESAB AB 2016

4 INSTALLATION

The installation must be carried out by a professional.

See the service manual Aristo® W82, Retrofit Mig 4004i WeldCloud™, WeldCloud™

Mobile.

For Retrofit Aristo® Mig 4004i WeldCloud™, make sure the antenna on the top box is not

covered or blocked.

4.1 Assembly instruction

Connection of Aristo® W82 to Mig 5000i, Mig 5000iw, Mig U5000i, Mig U5000iw power

source

1. Remove the screws on the rear handle of

the power source.

2. Put the W82onto the welding power

source.

3. Screw the W82and the handle into place

in the same screw holes.

Connection of Retrofit Aristo® Mig 4004i WeldCloud™

For instructions on how to connect the Retrofit Aristo® Mig 4004i WeldCloud™, see the

service manual for Aristo® W82, Retrofit Mig 4004i WeldCloud™ or contact the nearest

ESAB Service Center or distributor.

Connection of Aristo® W82 to Mig 3001i, Mig 4001i, Mig 4002c, Mig 5002c and Mig

6502c power sources

Connect the W82with a 2 m cable and place it on the floor or on a stand next to the power

source.

4.2 System description

It is possible to configure the U82unit for stand-alone usage (stand-alone unit) or

presentation usage (presentation unit). The presence of a W82unit within the welding system

determines which unit that is to be used.

4 INSTALLATION

0460 971 301 - 10 - © ESAB AB 2016

The stand-alone unit is used when there is

no W82unit in the system.

The presentation unit is used when there

is a W82unit in the system.

During unit start-up it is possible to see if the unit is a presentation unit or not.

4.3 How to set-up the U82 for use with W82

NOTE!

It is necessary to change the U82stand-alone unit to a presentation unit before it

is used together with a W82unit.

4.3.1 Save your stored data

1. Connect the U82stand-alone unit to a power source or a wire feed unit.

2. Turn ON the main switch on the power source.

3. Export weld data sets from the U82memory to a USB memory (see chapter

Export/Import in the U82instruction manual).

4. Turn OFF the main switch on the power source.

5. Remove the USB memory.

4.3.2 Convert the U82 stand alone unit to a presentation unit

1. Connect the enclosed USB memory to a PC. Make sure that the computer is set to show

file extensions.

2. Rename: "update.txt_" to "update.txt" and "reset.txt_" to "reset.txt"

Other manuals for Aristo W82

This manual suits for next models

Table of contents

Other ESAB Welding System manuals

ESAB

ESAB Powercut 650 User manual

ESAB

ESAB Warrior 400i CC/CV User manual

ESAB

ESAB Origo Mig 4002cw User manual

ESAB

ESAB Caddy Tig 1500i VRD User manual

ESAB

ESAB Aristo WeldCloud Mig U5000i User manual

ESAB

ESAB Cutmaster 100 SL100 1Torch User manual

ESAB

ESAB CIGWELD WeldSkill 185LCD User manual

ESAB

ESAB Renegade ES 210i User manual

ESAB

ESAB Cutmaster 40 User manual

ESAB

ESAB Origo Mig C141 User manual

ESAB

ESAB Caddy Tig 1500i User manual

ESAB

ESAB Renegade ET 300i User manual

ESAB

ESAB Powercut 900 User manual

ESAB

ESAB Aristo Mig U5000i 400 V User manual

ESAB

ESAB LKA 180 User manual

ESAB

ESAB Buddy Feed 402 User manual

ESAB

ESAB Origo Mag C140 User manual

ESAB

ESAB Retrofit Aristo Mig 4004i WeldCloud User manual

ESAB

ESAB EMP 210 User manual

ESAB

ESAB Retrofit Aristo Mig 4004i WeldCloud User manual

ESAB

ESAB Aristo WeldCloud Mig U5000i User manual

ESAB

ESAB PowerCut 700 PT-39 User manual

ESAB

ESAB Renegade ET 180iP User manual

ESAB

ESAB Powercut 650 User manual

Popular Welding System manuals by other brands

Berner

Berner PLASMACUT 54 instruction manual

Pro Spot

Pro Spot PR-155 Assembly instructions

Forney

Forney 210 operating manual

Thermal Arc

Thermal Arc 400S operating manual

Lincoln Electric

Lincoln Electric HANDYMIG 170I Operator's manual

GYS

GYS PROTIG 201 AC/DC Original instructions

TAFA

TAFA 30*8B35 owner's manual

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Technical specifications

CIGWELD

CIGWELD 636804 use instructions

Red-D-Arc

Red-D-Arc DC-400 Operator's manual

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 owner's manual

Elettro

Elettro HI-MIG 3000 SYNERGIC instruction manual

WIA

WIA Weldmatic 270 CP132-2 Operator's manual

Sonics

Sonics H520T instruction manual

Miller

Miller Big Blue 400D owner's manual

NewArc

NewArc RT2000 Operational manual

Hypertherm

Hypertherm powermax1000 Operator's manual

Lincoln Electric

Lincoln Electric POWER WAVE I400 Operator's manual