ESAB 35833 User manual

INSTRUCTIONS for F-15-342

July, 1996

F-15-342

DUAL CYLINDER RACK KIT

P/N 35833

FOR USE ON THE ESP-100i POWER SOURCE

This kit includes the following components (See Fig.1):

1 — Dual Cylinder Bracket, 36621

1 — Cylinder Rack, 30511

2 — Chain, 3 ft., 678944

4 — Screw, 3/8"-16 X 1" Long

4 — Lockwasher, 3/8"

4 — Flatwasher, 3/8"

8 — Screw 1/4"-20 X 1/2" Long

1 — Handle, 678402

2. Assemble the cylinder rack (35011) to the top rear

panel of the unit using four (4) 1/4-20 X 1/2" long

screws. Tighten all screws firmly with a wrench.

3. Slide at least the second link of each chain into the

center slot of the upper cylinder bracket.

4. Mount the handle to the top front of the ESP-100i

powersourceasillustrated,usingfour(4)1/4-20X1/

2" screws.

Whenyouputthecylindersinplace,pullthechaintightly

around each cylinder and slide a chain link into the outer

slot of the cylinder support. Be sure to pull the link down

firmly into each slot to secure the chain so that there is

little slack of the chain about the cylinder. DO NOT just

"loop" a link over the end of the rack.

Never lift a power source with cylinder(s) attached.

Be sure this information reaches the operator.

You can get extra copies through your supplier.

F-15-342 7/96 3C Printed in U.S.A.

(2) CHAIN, 36"

- 678944

CYLINDER RACK

SUPPORT - 30511

BRACKET, 2-Cyl. - 36621

(4) SCREW, 3/8-16 X 1"

(4) WASHER, 3/8"

(4) LOCKWASHER, 3/8"

(4) SCREW, 1/4-20 X 1/2", WASHER HEAD

(4) SCREW, 1/4-20 X 1/2", WASHER HEAD

To assemble the kit to the ESP-100i power source, re-

fer to Figure 1 and proceed as follows:

1. Assemblethedualcylinderbracket assembly(36621)

tothebaseoftherearsideofthepowersourceusing

four(4) setsof 3/8"-16X1" longscrews,lockwashers,

andwashers. Tightenthescrewsfirmly withawrench.

Fig. 1 - Mounting Dual Cylinder Rack Kit Components to ESP-100i Power Source

HANDLE - 678402

HANDLE - 678402

(4) SCREW, 3/8-16 X 1"

(4) WASHER, 3/8"

(4) LOCKWASHER, 3/8"

(4) SCREW, 1/4-20 X 1/2", WASHER HEAD

(4) SCREW, 1/4-20 X 1/2", WASHER HEAD

CYLINDER RACK

SUPPORT - 30511

(2) CHAIN, 36"

- 678944

BRACKET, 2-Cyl. - 36621

F-15-342 7/96 5C Printed in U.S.A.

Fig. 1 - Mounting Dual Cylinder Rack Kit Components to ESP-100i Power Source

Table of contents

Other ESAB Welding System manuals

Popular Welding System manuals by other brands

Berner

Berner PLASMACUT 54 instruction manual

Pro Spot

Pro Spot PR-155 Assembly instructions

Forney

Forney 210 operating manual

Thermal Arc

Thermal Arc 400S operating manual

Lincoln Electric

Lincoln Electric HANDYMIG 170I Operator's manual

GYS

GYS PROTIG 201 AC/DC Original instructions

TAFA

TAFA 30*8B35 owner's manual

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Technical specifications

CIGWELD

CIGWELD 636804 use instructions

Red-D-Arc

Red-D-Arc DC-400 Operator's manual

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 owner's manual

Elettro

Elettro HI-MIG 3000 SYNERGIC instruction manual

WIA

WIA Weldmatic 270 CP132-2 Operator's manual

Sonics

Sonics H520T instruction manual

Miller

Miller Big Blue 400D owner's manual

NewArc

NewArc RT2000 Operational manual

Hypertherm

Hypertherm powermax1000 Operator's manual

Lincoln Electric

Lincoln Electric POWER WAVE I400 Operator's manual