Ergotron 97 815 User manual
1 of 10
888-97-332-G-00 rev. D • 12/14
VESA Scanner Bracket
= 2.2 lbs (1 kg)
User's Guide - English
Guía del usuario - Español
Manuel de l’utilisateur - Français
Gebruikersgids - Deutsch
Benutzerhandbuch - Nederlands
Guida per l’utente - Italiano
Användarhandbok - svenska
ユーザーガイド: 日本語
用户指南 : 汉语
CAUITON: Make sure you know the max. weight capacity of your mounting solution before attaching the scanner shelf. Include the
weight of your monitor, scanner shelf, scanner base and scanner: when guring mounted weight on your mounting solution. Failure
to follow this Caution may lead to equipment damage and/or personal injury.
For the latest User Installation Guide please visit: www.ergotron.com
2 of 10
888-97-332-G-00 rev. D • 12/14
M5
M4
M4
M4 SEM
M5
1x
5x
5x
1x
M4 x 10mm
M4 x 35mm
M4 x 14mm
M3.5 x 8mm
M3 x 10mm
6x
1x
1x
2x
1x
4x
1x
1x
1x 1x
6x
7mm
8mm
1x 8-32 x 5/16"
Components
Tools Needed
3 of 10
888-97-332-G-00 rev. D • 12/14
1
ab
c
1x 1x1x
1x
M3 x 10mm M4 x 10mmM3.5 x 8mm
M4
A "stop rotate" screw will keep your display from rotating, which could cause the mounted scanner to fall o. There
may already be a "stop rotate screw" installed between your display and theVESA plate.
a) Test to see if a "stop rotate screw" is installed by trying to rotate your display. If it will not turn, the "stop rotate screw" is already
installed, skip steps 1b - 1d below, and go straight to step 2 on the next page. If your display rotates freely, you'll need to install one of the
provided "stop rotate screws" as shown in steps 1b - 1d below.
b) Rotate your diplay to the orientation you will be using it in from now on (once you install the "stop rotate screw", the display will be
xed in either portrait or landscape position). Remove the display from theVESA plate with a phillips screwdriver. You can discard the
screws or thum screws since replacements are provided with this product.
c) Insert the provided washer and one of the three provided stop-rotate screws : M3x10 mm, M3.5x8mm, or M4x10mm depending on the
diameter of the hole in yourVESA plate.
d) Reattach your display to the VESA plate using two of the provided M4x10mm screws. NOTE: insert the screws into theVESA plate oposite
the side of the display that the scanner will be mounted! If thumb screws were previously inserted, do not use them.
4 of 10
888-97-332-G-00 rev. D • 12/14
2
d
M4 x 14mm
2x
M4 x 14mm
2x
2x
M4 x 10mm
1A
NOTE: insert the screws into the VESA
plate oposite the side of the display
that the scanner will be mounted!
Right-mount scanner holder position
M4x10mm
screws are located on
the left side of the
VESA plate.
M4x10mm screws are
located on the right side
of the VESA plate.
Left-mount scanner holder position
Attach part "1A" to VESA plate at the back of your display. Insert two of the provided M4x14mm phillips screws
through the bracket, the VESA plate and display.
NOTE: Do not use thumb screws
for this installation!
5 of 10
888-97-332-G-00 rev. D • 12/14
4
31B
2x
M4 x 10mm
Loosen the thumb screw on part "1A" (at the back of the display) and adjust so that part "1B" comes
into contact with the side of the display.
Loosen the thumb screw on part "1A" (at the back of the display) and adjust so that part "1B" can be
attached to part "1A", then attach "1B" to "1A".
6 of 10
888-97-332-G-00 rev. D • 12/14
6
5Pull the front section of part "1B" forward so that it grips the front of the display.
Tighten with phillips screwdriver until snug.
Tighten the front screw until the spacer holds the display snug.
7 of 10
888-97-332-G-00 rev. D • 12/14
8
7
2A
Adjust the L-bracket to desired height and tighten screws with a at-head screwdriver.
NOTE: If the scanner is mounted too low it may interfere with the
keyboard tray when moved into the full-up position. In that case, raise
the scanner L-bracket (part "2A") higher in relation to the display.
Slide part "2A", L-bracket, into part "1B"
8 of 10
888-97-332-G-00 rev. D • 12/14
9
M4 SEM
M4 x 14mm
4x
2x
M4
M4
M5
M5
M4
M4
2x
4x
1x
1x
2x
4x
1x
1x
M5
M5
Choose the scanner mount conguration that matches your scanner.
4-corner mount: attach interface plate to L-bracket using 1 washer and 1 nut,
then attach scanner base with 4 phillips screws, 4 washers and 4 nuts.
Keyhole mount: attach interface plate to L-bracket using 1 washer and 1 nut,
then attach scanner base using 2 shoulder screws, 2 washers and 2 nuts.
9 of 10
888-97-332-G-00 rev. D • 12/14
M4
M4
M4
M4
1x
1x
1x
1x
1x
8-32 x 5/16"
M4 x 35mm
M4 x 35mm
1x
1x
Single hole, center mount: scanner base attaches directly to the
L-bracket using: 1 screw, washer and nut.
Single hole, center mount plus side screw: scanner base attaches
directly to the L-bracket using: 1 screw from bottom, 1 screw from
top with washer and nut.
10 of 10
888-97-332-G-00 rev. D • 12/14
10
Adjustment Step
Route cables.
Adjust your mounting solution to handle the added weight.
Adjustments should move smoothly and easily through the full range of motion and stay where you set it. If adjustments
are dicult and do not stay in the desired position, follow the instructions to loosen or tighten the tension to create a
smooth, easy adjustment motion. Depending on your product and the adjustment, it may take several turns to notice a
dierence.
For local customer care phone numbers visit: http://contact.ergotron.com
Table of contents
Other Ergotron Rack & Stand manuals
Ergotron
Ergotron Zido User manual
Ergotron
Ergotron LX Dual Side-by-Side Arm User manual
Ergotron
Ergotron Neo-Flex User manual
Ergotron
Ergotron NF User manual
Ergotron
Ergotron LX Sit-Stand Collar Kit User manual
Ergotron
Ergotron Tablet Management Wall Mount 10 User manual
Ergotron
Ergotron Neo-Flex LCD Arm User manual
Ergotron
Ergotron LX User manual
Ergotron
Ergotron LX Desk Mount LCD Arm User manual
Ergotron
Ergotron DS100 Series User manual
Ergotron
Ergotron 100 Series User manual
Ergotron
Ergotron Command Post User manual
Ergotron
Ergotron StyleView Sit Stand Combo Arm User manual
Ergotron
Ergotron AnthroBench 293 Series User manual
Ergotron
Ergotron Neo-Flex 45-174-300 Dimensions
Ergotron
Ergotron MX Desk Mount LCD Arm User manual
Ergotron
Ergotron Power Strip User manual
Ergotron
Ergotron Neo-Flex 33-334-085 Dimensions
Ergotron
Ergotron MXV User manual
Ergotron
Ergotron WorkFit-B User manual
Popular Rack & Stand manuals by other brands
Salamander
Salamander Acadia AC/W/L400/WH Assembly instructions
Fohhn
Fohhn VAT-09 Mounting instruction
ricoo
ricoo FS0522 quick start guide
AMSOIL
AMSOIL BMK-22 Installation and service instructions
Kargo Master
Kargo Master 48220 installation guide
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 installation instructions
