ErgoAV ERTSL2-01B User manual
Model: ERTSL2-01B
Table Top TV Stand Instruction Manual
V1.0
THANK YOU FOR CHOOSING THIS ERGOAV PRODUCT!
At ErgoAV, we want to add value to your AV experience by providing the highest
quality products and services in the industry. If you have any concerns or
comments, please contact us.
ErgoAV Customer Care
Phone (877) 419-7832 M-F 8am to 8pm CST
email: [email protected]
website: www.ergoav.com
adress: 9501 Louisiana Ave N, #200 Brooklyn Park, MN 55445
English pages: 02-16 French pages: 17-30 Spanish pages: 31-46
Before getting starting, let's make sure this mount is perfect for you!
IMPORTANT SAFETY INFORMATION
CAUTION: Avoid potential personal injuries and property damage!
Do not use this product for any purpose that is not explicitly specified in this
manual. Do not exceed weight capacity. We are not liable for damage or
injury caused by improper mounting, incorrect assembly or inappropriate use.
Please carefully read all instructions before attempting assembly. If you do
not understand the instructions or have any concerns or questions, please
contact our Technical Support line at (877) 419-7832 or customer service at
99 lbs/
44.9 kg
1
Measure Your TV VESA Pattern:
Minimum: 100 x 100mm/4 x 4 in (WxH)
Maximum: 600 x 400mm/24 x 16 in (WxH)
1
W
H
Solid Concrete
or Concrete Block
DO NOT install into drywall alone.
Wood Studs
(with Drywall)
For safety strap
installations, you will
need to verify your
wall construction.
If this mount is NOT compatible, please contact our Technical Support line at
mount.
If your TV is not between the minimum and
maximum measurements, do not use
this product.
If your TV weighs more than 99 lbs,
do not use this product.
02
Supplied Parts and Hardware
WARNING: This product contains small items that could be a choking
hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. Do not
use damaged or defective parts. lf you require replacement parts, please
contact our Technical Support line at (877) 419-7832 or customer service at
• Please note: Not all hardware included in this package will be used.
Tools Needed (Not lncluded)
AwlStud Finder
Tape Measure
Tape
Measure
Tape
Measure Pencil
Pencil
1/8 in (3mm)
Wood Drill Bit
5/16 in (8mm)
Concrete Drill Bit Hammer
Drill
Drill
Phillips
Screwdriver
Phillips
Screwdriver
Phillips
Screwdriver
For safety straps installation into concrete wall
For safety strap installatcon into wood table/furniture and wood stud applications
For TV stand assembly
(B1) x4
M4/M5
Washer
(B2) x4
M6/M8
Washer
(N) x2
TV Bracket
Supplied Parts and Hardware for Step 1
03
Step 1 Secure the TV Brackets [N] to TV
Select TV Bolts
Only one bolt size fits your TV.
(C1) x4
M4x12mm
Bolt
(C2) x4
M4x30mm
Bolt
(D1) x4
M6x15mm
Bolt
(D2) x4
M6x35mm
Bolt
(E1) x4
M8x15mm
Bolt
(E3) x4
M8x50mm
Bolt
Bolts and spacers are shown in actual size.
(F1) x8
L2.5mm
Spacer
(F2) x4
L10mm
Spacer
(F3) x4
L22mm
Spacer
(E2) x4
M8x35mm
Bolt
Bolt length: Verify adequate thread engagement with bolts or bolts/spacers
combination. We recommend thread engagement by at least 5 turns.
-Too short will not hold the TV.
-Too long will damage the TV.
OR OR
Too Short Correct Too Long
M6 M8M4
04
Please Note: When using the spacers it is important to note that they can be used in
multi-layers (meaning stacked). If you have any difficulty understanding how to install
the TV bolts or spacers, please contact our Technical Support line at (877) 419-7832
N
When attaching the TV brackets to the
back of the TV, ensure the Up Arrows are
pointing to the top of the TV and are
equally centered on the back of the TV.
UP
TV Brackets have “three height locations”, which determines the height
position of your TV while attaching your TV on the stand in Step 5 on page 11.
You can choose the proper height.
Height Location #1
Height Location #3 Height Location #2
Bump
See Option C Cables
See Option D Recessed Holes
See Option E
Spacers
Curved TV
See Option B
Parts Needed if You Have a TV as Shown Below
F1+F1 F1+F2 F1+F3F1+F1+F2 F1+F1+F3 F2+F3 F1+F2+F3 F1+F1+F2+F3
05
Option A (For Flat Back TV )
B1/B2
C1/D1/E1
Option B (For Curved Back TV)
Option C (For TV with A “Bump”)
B1/B2
C2/D2/E2/E3
Phillips Screwdriver
(Not lncluded)
Refer back to Spacer Instructions
on Page 05, If needed
B1/B2
C2/D2/E2/E3
F1/F2/F3
Spacers must be large enough so TV bracekts are flush (NO GAP) on bump.
Refer back to Spacer Instructions
on Page 05, If needed
Spacers must be tall enough so that the curve on the back of the TV will not
interfere with the mounting plate.
F1/F2/F3F1/F2/F3
06
Option D (for TV with Cable Interference)
Option E (For Recessed Holes ）
For cable interference, use spacers [F1], [F2] and [F3]
to create extra space between the TV and TV brackets.
N
Phillips Screwdriver
(Not lncluded)
Refer back to Spacer Instructions
on Page 05, If needed
Refer back to Spacer Instructions
on Page 05, If needed
N
The spacer need to fill in the recessed holes on the basis of the TV so
that the TV brackets are as close to the TV as possible.
C2/D2/E2
B1/B2
F1/F2/F3
C2/D2/E2/E3
B1/B2
F1/F2/F3
F1/F2/F3F1/F2/F3 B1/B2
C2/D2/E2/E3
B1/B2
C2/D2/E2/E3
07
Step 2-1
(W) x6
Foot Pad
(R) x1
Reinforcement
Plate
(Y) x1
Trim Ring
Supplied Parts and Hardware for Step 2
This bolt is shown in
actual size.
(L) x3
M6x25mm
Bolt (P) x1
Support Pillar
(O) x1
Tempered
Glass Base
(V) x1
5/32 in (4mm)
Allen Key
Step 2 Assemble the Base
Connect the support pillar [P] to tempered glass base [O]
R
OYP
L
V
When assembling the support pillar
[P], ensure the side of the reinforcing
plate [R] with paper is facing the
glass base [O].
Note: Do Not
overtighten the
bolts [L].
O
V
LR
P
Table
Step 2-2
Place foot pads [W] to
the painted side of the
tempered glass
base [O] in the
corners W
Table
O
W
08
Distance from the hooks on the TV
Brackets to the bottom of the TV Recommended TV Mounting
Plate Location
20 1/8" to 23 1/2"
16 3/4" to 20 1/8"
Less Than 16 3/4"
Location #1
Location #2
Location #3
Note: Before attaching the TV Mounting
Plate to the pillar, measure the distance
from the upper hook on the TV Bracket
to the bottom of the TV. Then refer to
chart below for the recommended
mounting location. To add an additional
“2” of space between your TV and the
base, use the lower hooks located on
the TV Brackets. We always recommend
using the lowest possible attachment
location for the safest assembly.
(M) x1
TV Plate
(X) x2
Safety Strap
Supplied Parts and Hardware for Step 3
(V) x1
5/32 in (4mm)
Allen Key
(S) x4
M6x50mm
Bolt
This bolt is shown in actual size.
Step 3 Connect the TV Plate [M] to Support Pillar [P]
Mounting Location #1
Mounting Location #2
Mounting Location #3
(T) x4
M6x8mm
Bolt
(A) x1
Swivel Component
Location #1Location #1
Location #2Location #2
Location #3Location #3
09
Connect swivel component [A]
and safety straps [X] to support
pillar [P] using bolts [S] by the
allen key [V].
Connect TV plate [M] to
swivel component [A]
using bolts [T] by the
allen key [V].
(K) x2
Wire Clip
Supplied Part for Step 4
PX
AS
T
Note: Make sure the
bump of the TV plate
faces back side of
the TV stand.
You may need assistance with this step
A
M
10
This manual suits for next models
1
Table of contents
Languages:
Other ErgoAV Rack & Stand manuals
Popular Rack & Stand manuals by other brands
Salamander
Salamander Acadia AC/W/L400/WH Assembly instructions
Fohhn
Fohhn VAT-09 Mounting instruction
ricoo
ricoo FS0522 quick start guide
AMSOIL
AMSOIL BMK-22 Installation and service instructions
Kargo Master
Kargo Master 48220 installation guide
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 installation instructions
