Eplus L-2140D User manual

ELECTRO-HYDRAULIC 2-POST LIFT

L-2140D

ASSEMBLY MANUAL

Ver.20.2.2

L-2140D ASSEMBLY MANUAL

This manual has been prepared for workshop personnel expert in the use of the lift (operator) and technicians responsible

for routine maintenance (Maintenance ﬁtter).

This manual must be read with User’s Manual.

The lifting, transport, unpacking, assembly, installation, starting up, initial adjustment and testing, extraordinary mainte-

nance, repair, overhauls, transport and dismantling of the lift must be performed by specialized personnel from the licensed

dealer or a service center authorized by the manufacturer.

ALL PACKING, LIFTING, HANDLING, TRANSPORT AND UNPACKING OPERATIONS ARE TO BE PERFORMED EXCLUSIVELY BY EXPERT

PERSONNEL.

SKILLED AND AUTHORIZED PERSONNEL ONLY SHOULD BE ALLOWED TO PERFORM THESE OPERATIONS, FOLLOW ALL INSTRUC-

TIONS SHOWN BELOW CAREFULLY, IN ORDER TO PREVENT POSSIBLE DAMAGE TO THE CAR LIFT OR RISK OF INJURY TO PEOPLE.

BE SURE THAT THE OPERATING AREA IS CLEARED OF PEOPLE.

L-2140D ASSEMBLY MANUAL

Step

To disassembly the package and

remove all components and accessories.

L-2140D ASSEMBLY MANUAL

12 x

Step

To remove ﬁxing bolts of packing brackets.

L-2140D ASSEMBLY MANUAL

Install area

Operator zone

Step

To move two columns to install area.

Pay attention: to recognize and decide

command and slave column’s position

to install.

L-2140D ASSEMBLY MANUAL

Step

To lift up two columns.

L-2140D ASSEMBLY MANUAL

Step

To measure the distance of two columns,

and two columns face each other accurately.

L-2140D ASSEMBLY MANUAL

Step

To install the beam.

L-2140D ASSEMBLY MANUAL

Step

To install the beam.

Pay attention to the limit switch on beam and

power unit support should be on the same side.

L-2140D ASSEMBLY MANUAL

Percussion drilling

chopping bit 18.5mm

depth 150mm

1Air purge to remove

dust inside of hole.

Insert bolt with bushes and

screw nut, not to tighten to

death, insert bushes under

the column baseplate to

adjust, by aid of spirit level

measurement to make

column to be vertical at 90°.

Insert long pin with

hammer to hit in to

the end。

Step

To ﬁx well columns.

Other Eplus Lifting System manuals

Eplus

Eplus L-2040D User manual

Popular Lifting System manuals by other brands

morse

morse 82H-124 Operator's manual

Braun

Braun NL955 Series Operator's manual

haacon

haacon 1889.10 quick start guide

Protekt

Protekt AT 252 instruction manual

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 operating manual

Nova Technology International, LLC

Nova Technology International, LLC NAS Series quick start guide

Genie

Genie Z-60/34 Operator's manual

Screen Technics

Screen Technics INTERFIT Vertical Up Lift instructions

Mortuary Lift

Mortuary Lift ULTIMATE 1000 instructions

Custom Equipment

Custom Equipment Hy-Brid 3 Series MAINTENANCE & TROUBLESHOOTING MANUAL

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Maintenance and troubleshooting manual

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 MAINTENANCE & TROUBLESHOOTING MANUAL

BERG

BERG BeNomic EasyLeaf Technical manual

Powermate

Powermate LiftGate LG-3 Installation & operation manual

Snorkel

Snorkel TM12 Series Operator's manual

Terberg

Terberg OMNIDEKA Translation of the original instructions

Harmar Mobility

Harmar Mobility AL625 Installation & owner's manual

Rotary

Rotary SPO16 installation instructions