Episode EA-WAKE-2D User manual

EA-WAKE-2D

Wake Amp

Owner’s Manual

Introduction

Thank you for purchasing Episode® Electronics. To complete installation, follow these guidelines. Visit

our website for design recommendations and speaker calculators.

Contents

• 1x WAKE Amp

• 2x Junction box screws

• 1x Face plate

• 2x Faceplate screws

• 1x Power supply

• 1x Power supply adapter

Selecting Wire

The WAKE Amp can accommodate 14 to 22 gauge speaker wire. The longer your run, the thicker

the wire should be. All in-wall and in-ceiling wire installations are subject to local code ﬁre ratings.

Never use lamp or zip cord for an installation where the wire will be in a wall or ceiling. Always use

multi-strand copper speaker wire for your installations. UV protected wire should be used for outdoor

installations.

• Check your local building and ﬁre rating codes for low voltage device installation & wiring

requirements before you begin your installation.

• In existing construction installations, check for obstructions such as any pipes, conduit or wiring

before cutting into drywall.

Selecting a Junction Box

The WAKE Amp is compatible with deep and backless single gang plastic back boxes.

Caution: Do not use a metal back box as it signiﬁcantly impacts Bluetooth performance

and range.

Getting Connected

1. Strip back 1/4” of insulation from each wire that is to be connected to the ampliﬁer. Twist the

exposed conductors tightly so there are no stray strands.

2. Connect the wires going to each speaker making sure to maintain proper polarity.

Warning: Do not connect the power supply to AC power while wiring the WAKE Amp.

3. Once all conductors are inserted into the connectors, visually inspect each of your connections

to ensure that there are no stray strands or exposed wire, that could cause a short. Make sure

that the connection is tightened down on bare wire and not insulation.

CAUTION: Reversing the power and speaker connections can cause damage to the

ampliﬁer or speakers and is not covered under warranty.

4. Install the ampliﬁer in the junction box using the provoided junction box screws. Be careful not

to force the ampliﬁer into the box, as this may cause the connections to become loose.

5. Place the wall plate over the WAKE Amp, then insert and tighten the short faceplate screws until

the cover is tight and ﬂush with the wall.

6. Use the supplied adapter to connect the amp to the power supply.

+ Right

– Right

+ Left

– Left

– Power

+ Power

–

To Right Speaker

To Left Speaker

To Power

–

Mobile App Setup

Download the WAKE Amp mobile app from the Apple App Store or Google Play store.

Open the app and it automatically searches for available WAKE Amps. Tap the WAKE Amp you want

to conﬁgure and the Amp Setup page appears.

Tap the icons along the bottom of the page, to navigate through conﬁguration options.

To disconnect from a WAKE Amp, tap the overﬂow icon ( ), in the upper right corner.

Amp Setup Tab

The Amp Setup tab contains general setup options. The following sections outline each header and

it’s respective ﬁelds.

LED Settings

• LED Timeout After 10 Seconds. Toggle on for the LEDs to turn o after 10 seconds of inactivity.

• LED Brightness. Use the slider to adjust the brightness of the LEDs.

Keypad Volume Settings

• Keypad Controls Volume. Selecting this feature causes the WAKE Amp’s buttons to control the amp

volume.

• Keypad Controls Music. Selecting this feature causes the WAKE Amp’s volume to be controlled by

the source and the WAKE Amp’s buttons control track forward, back and pause.

• Amp Fixed Volume. Sets ﬁxed ampliﬁer level for use when volume is being adjusted at the source.

Use this slider to optimize output level without overdriving ampliﬁer.

Note: This feature is only available when Keypad Controls Music is selected.

Name Change

Tap the pencil icon to edit the name of the WAKE Amp. It’s best to name the WAKE Amp after the

location it’s installed in.

Speaker Size

Tap to select the size of the connected speakers to properly tune the WAKE Amp.

Use the Small setting for in-celing, in-wall, or bookshelf speakers. Use the Large settings for

ﬂoorstanding or other large speakers.

Bluetooth Reconnect

Toggle on to have the WAKE Amp try to automatically reconnect to the paired Bluetooth device, if

disconnected.

If toggled o, the WAKE Amp automatically enters Bluetooth Pairing mode after disconnecting from a

paired device.

EQ Tab

The EQ tab includes Treble and Bass adjustments.

Loudness boost is a dynamic EQ boost to both bass and treble when the amp is at lower volumes.

This feature makes the speakers sound more dynamic at lower volumes without coloring the speaker

at higher volumes.

Info Tab

The Info tab displays the WAKE Amp’s current ﬁrmware version and a link to the device manual.

Firmware Tab

The ﬁrmware tab checks for new ﬁrmware versions. Tap the Update button to push ﬁrmware updates

via Bluetooth.

Note: The ﬁrmware update process uses Bluetooth to transfer the ﬁrmware ﬁle from the

mobile device to the WAKE Amp. This process can take up to 20 min. To reduce ﬁle

transfer time ensure that the mobile device is in close proximity to the WAKE Amp.

Pairing Your Bluetooth Device To The WAKE Amp

Press and hold the button for 5 seconds to enter pairing mode on the WAKE Amp. LEDS 1-5

start to run from left to right and the WAKE Amp’s name appears in the Discoverable list of the device

you’re pairing it to.

The WAKE Amp may appear twice in some devices Discoverable list. Once as a traditional audio

Bluetooth connection, and again as a Bluetooth low energy data connection (used for communication

with the mobile app). Be sure to connect to the WAKE Amp’s audio device connection.

Note: Wireless devices may be susceptible to RF interference from other devices. To reduce

potential interference and maximize wireless performance, check the proximity to

other wireless devices and relocate them accordingly. Signal interference created by

microwave ovens, ceiling fans, or other appliances subsides when those devices are not

in use.

Button Behavior

Button Volume Mode Music Mode

Volume Up Next Track

Volume Down Previous Track

Mute Play/Pause

LEDs

Numbered 1 through 5, from left to right. The following table describes the

LED behaviors.

Function LED Behavior

Firmware Update LED 1 blinks during update process.

Mute/Pause LED 1 illuminates red.

No Source Connected LED 1 slowly blinks blue.

Factory Reset LEDs 1-5 blink red.

Bluetooth Pairing Mode LEDs 1-5 blink blue.

Error LEDs 1-5 illuminate red.

Current Volume

LEDs 1-5 illuminate blue to show the current

volume level. For example, if LEDs 1 and 2 are

illuminated the volume is at 40%.

Factory Reset Procedure

Press and hold the and buttons until the LEDs blink red, then release the buttons.

LEDs 1 through 5 blink red and blue during the procedure. Once they stop, use the WAKE Amp mobile

app to set up the amp again.

Note: Factory resetting the amp also resets the paired device list, so the user must pair the

WAKE Amp to the source again.

Firmware Recovery Mode

There are two ways to recover a WAKE Amp if it fails a ﬁrmware update. Once restored, try the

ﬁrmware update again.

Hardware Method

1. Remove power by unplugging the power supply from the AC power outlet.

2. Press and hold the and buttons.

3. Plug the power supply back in to the AC power outlet.

4. Once LEDs turn on pink, release the buttons.

5. All LEDs slowly blink pink. The unit is validating the stored factory default ﬁrmware ﬁle.

6. All LEDs quickly blink pink. The unit is reprogramming the processor memory.

7. LED 1 blinks pink. The unit is reprogramming the Bluetooth module.

8. LED 1 blinks blue. The unit is ready to use.

Software Method

1. Press and hold the and buttons.

2. Once LEDs start blinking red, release the buttons.

3. While the LEDs are still blinking red, press and hold the and buttons once more.

4. Once the LEDs turn pink, release the buttons.

5. All LEDs slowly blink pink. The unit is validating the stored factory default ﬁrmware ﬁle.

6. All LEDs quickly blink pink. The unit is reprogramming the processor memory.

7. LED 1 blinks pink. The unit is reprogramming the Bluetooth module.

8. LED 1 blinks blue. The unit is ready to use.

Restarting the WAKE Amp

Press and hold the button. Continue holding while LEDs 1-5 start blinking blue, then release

the button when they start blinking red.

Note: If you continue to hold the button, the LEDs stop blinking. Releasing the button after this

time has no eect and you’ll have to try again.

Speciﬁcations

Input Voltage 100V - 240V

Power Consumption for Power

Supply 1.5A

Power Output 60W

Output Voltage 15V

Power Consumption 4A

Channels 2

Power Output @ 4 ohms 25W/Ch

Frequency Response 20Hz - 20kHz

Wireless Protocols Bluetooth Class 1/BLE

Range Up to 30m*

Installation Compatible with deep and backless single-gang plastic back boxes

Dimensions (W x H x D) 101.7 mm (4”) x 38.5 mm (1.5”) x 81mm (3.2”)

Weight 114 g (.25 lb)

*Varies depending on the Bluetooth source.

Technical Support

For chat and telephone, visit tech.control4.com/s/contactsupport • Email: T[email protected]om. Visit tech.control4.

com for discussions, instructional videos, news, and more.

Warranty and Legal Notices

Find details of the product’s Limited Warranty at snapone.com/legal/ or request a paper copy from Customer Service at

866.424.4489. Find other legal resources, such as regulatory notices and patent and safety information, at snapone.com/

legal/ .

of Snap One, LLC (formerly known as Wirepath Home Systems, LLC), in the United States and/or other countries. 4Store,

4Sight, Control4, Control4 My Home, SnapAV, Araknis Networks, BakPak, Binary, Dragonﬂy, Episode, Luma, Mockupancy,

Nearus, NEEO, Optiview, OvrC, Pakedge, Sense, Strong, Strong Evolve, Strong VersaBox, SunBriteDS, SunBriteTV, Triad,

Truvision, Visualint, WattBox, Wirepath, and Wirepath ONE are also registered trademarks or trademarks of Snap One, LLC.

Other names and brands may be claimed as the property of their respective owners. Snap One makes no claim that the

information contained herein covers all installation scenarios and contingencies, or product use risks. Information within this

speciﬁcation subject to change without notice. All speciﬁcations subject to change without notice.

Version 211020

200-EA-WAKE-001-A

This manual suits for next models

Table of contents

Other Episode Amplifier manuals

Episode

Episode ECA-70VMINI-60W User manual

Episode

Episode EA-AMP-12D-70A User manual

Episode

Episode EA-AMP-SUB-1D-500 User manual

Episode

Episode EA-AMP-SUB-1D-500R User manual

Episode

Episode E-1230-A User manual

Episode

Episode EA-AMP-SUB-1D-300 User manual

Episode

Episode EA-AMP-HYB-2D-1000 User manual

Episode

Episode CR-CDI1000-LSCAPE Instruction manual

Episode

Episode EA-AMP-HYB-2D-1000 User manual

Episode

Episode ECA-70VMINI-60W User manual

Episode

Episode EA-AMP-SUB-1D-500R User manual

Episode

Episode CR-CDI1000-LSCAPE User manual

Episode

Episode EA-RSP-2D-200 User manual

Episode

Episode ECA-70MIXAMP-1-120 User manual

Episode

Episode DYNAMIC Series User manual

Episode

Episode EA-AMP-12D-70 User manual

Episode

Episode EA-AMP-12D-45A User manual

Episode

Episode EA-MINI-2D-35 User manual

Episode

Episode EA-AMP-COMM-1A-120 User manual

Episode

Episode EA-MINI-SUB-1D-100 User manual

Episode

Episode E-2100 User manual

Episode

Episode ECA-70MIXAMP-1-240 User manual

Episode

Episode EA-AMP-SUB-1D-110 User manual

Episode

Episode EA-AMP-HYB-2D-1000 User manual

Popular Amplifier manuals by other brands

ASTRO

ASTRO HVO V40 P operating manual

Marantz

Marantz SUPERSCOPE BLA-545 Service data

NAD

NAD CI980 Quick setup guide

Technics

Technics SE-CH770 Service manual

Harman Kardon

Harman Kardon HK6300 instruction manual

NAD

NAD T975 owner's manual

McIntosh

McIntosh MA6850 Brochure & specs

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N manual

Viatron

Viatron Autrix Technical manual

GME

GME GA9800 instruction manual

Atlas

Atlas CP700 Specification sheet

Roland

Roland KC-1000 owner's manual

Pyle

Pyle PFMRA350BW user manual

Advantage

Advantage S-250 manual

IRT Electronics

IRT Electronics DVA-3007 manual

Dimavery

Dimavery BA-100 Series user manual

Sony

Sony XM-S400D operating instructions

Schertler

Schertler ROY X quick guide