Enviro Cube Manual

CubeUnpacking&SetupInstructions

Contents

• Black sea ember wool (x1)

• Rear Vent Top Cover (x1)

• Unpacking & Setup Guide

(x1)

1. Remove the crate and packaging from the

unit. The unit is attached to the pallet and

will be removed at a later step.

Figure 1: Safety Screen Removal

Figure 2: Back Cover Removal

3. The rear panel is attached to the unit using

four (4) #8 T20 screws, two (2) on each side

near the back of the unit. Detach these

screws and remove the back panel. Refer to

Figure 2.

2. Remove the safety screen from the front of

the unit. Lift the screen up to disengage the

hooks and pull away from the unit. Refer to

Figure 1.

4. Lift the top cover up and o of the unit

(see Figure 3).

Figure 3: Top Plate Removal

5. Remove the front glass by lifting up to

disengage the hooks and pull away from

the unit. Refer to Figure 4.

Figure 4: Outer Glass Removal

6. Each of the side panels can now be

removed. Lift the panel up and away

from the unit. Refer to Figure 5.

Figure 5: Side Panel Removal

Figure 6: Unit Removal

7. The Cube is attached to the pallet via two

brackets at the bottom of the unit. Detach the

unit from these brackets by removing the four

(4) #8 HEX screws, two on each side. Lift the

unit up and place it off to the side for now.

Refer to Figure 6.

8. Remove the wood screws securing the brack-

ets to the pallet.

*NOTE: The next steps apply to both the pedes-

tal and platform options for the Cube. The shown

diagrams will use the pedestal as an example.

*NOTE: If you are planning to install the optional

fan kit, please complete everything up to wiring

the fan kit before continuing. The fan kit installa-

tion instructions are included with the fan kit.

*NOTE: If converting the Cube to a rear vented unit, unscrew the four (4) hex head bolts securing

the intake/exhaust adapter, rotate it 180º, and reat-tach.

*NOTE: If you are installing the optional fan kit, finish the remaining instructions (wiring the fan

kit) before continuing.

9. Place two brackets on the table and line up

the holes on the bracket to the table. Use four

(4) #8 T20 Screws to fasten. (Figure 7)

10. Retrieve the Cube unit and align it over the

brackets on the pedestal/platform. It will use the

same holes that the brackets were previously

attached to. Secure the unit to the pedestal as

shown in Figure 7.

11. The Cube is now properly secured to the

pedestal/platform. perform steps 2 through 6 in

reverse order to reattach all outer pieces of the

unit. Figure 7: Unit Attachment

Other manuals for Cube

1

Table of contents

Other Enviro Indoor Fireplace manuals

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Desa

Desa CCFPDFT Owner's operating & installation manual

Miles Industries

Miles Industries Vogue 1300IRN Installation & operating instructions