Enterasys Matrix-V V2H124-24FX Manual

P/N 9033984-02

Matrix V-Series

V2H124-24FX

Fast Ethernet Switch

Hardware Installation Guide

Notice

ENTERASYS NETWORKS reserves the right to make changes in specifications and other

information contained in this document and its web site without prior notice. The reader should

in all cases consult ENTERASYS NETWORKS to determine whether any such changes have

been made.

The hardware, firmware, or software described in this document is subject to change without

notice.

IN NO EVENT SHALL ENTERASYS NETWORKS BE LIABLE FOR ANY INCIDENTAL,

INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING

BUT NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS

DOCUMENT, WEB SITE, OR THE INFORMATION CONTAINED IN THEM, EVEN IF

ENTERASYS NETWORKS HAS BEEN ADVISED OF, KNEW OF, OR SHOULD HAVE

KNOWN OF, THE POSSIBILITY OF SUCH DAMAGES.

Enterasys Networks, Inc.

50 Minuteman Road

Andover, MA 01810

Printed in Taiwan

Release Date: October 2004

ENTERASYS NETWORKS, ENTERASYS MATRIX, LANVIEW, MATRIX,

NETSIGHT,WEBVIEW, and any logos associated therewith, are trademarks or registered

trademarks of Enterasys Networks, Inc. in the United States and other countries.

All other product names mentioned in this manual may be trademarks or registered trademarks

of their respective companies.

Matrix V-Series Documentation URL: http://www.enterasys.com/support/manuals

ELECTRICAL HAZARD: Only qualified personnel should

perform installation procedures.

Notice

Regulatory Compliance Information

Federal Communications Commission (FCC) Notice

This device complies with Part 15 of the FCC rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a class A

digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment uses, generates, and can radiate radio frequency

energy and if not installed in accordance with the operator’s manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is likely

to cause interference in which case the user will be required to correct the interference at his

own expense.

WARNING: Changes or modifications made to this device which are not expressly approved

by the party responsible for compliance could void the user’s authority to operate the

equipment.

Industry Canada Notice

This digital apparatus does not exceed the class A limits for radio noise emissions from digital

apparatus set out in the Radio Interference Regulations of the Canadian Department of

Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites

applicables aux appareils numériques de la class A prescrites dans le Règlement sur le

brouillage radioélectrique édicté par le ministère des Communications du Canada.

AS/NZS CISPR 22

N826

Notice

iii

VCCI Notice

This is a class A product based on the standard of the Voluntary Control Council for Interference

by Information Technology Equipment (VCCI). If this equipment is used in a domestic

environment, radio disturbance may arise. When such trouble occurs, the user may be required

to take corrective actions.

Class A ITE Notice

WARNING: This is a class A product. In a domestic environment this product may cause

radio interference in which case the user may be required to take adequate measures.

BSMI EMC Statement — Taiwan

This is a class A product. In a domestic environment this product may cause radio interference

in which case the user may be required to take adequate measures.

ENVIRONMENTAL REQUIREMENTS

PRODUCT SAFETY

This product complies with the following: UL 60950, CSA C22.2 No. 60950, 73/23/EEC,

EN 60950, IEC 60950, EN 60825, 21 CFR 1040.10.

ELECTROMAGNETIC COMPATIBILITY (EMC)

This product complies with the following: 47 CFR Parts 2 and 15, CSA C108.8, 89/336/EEC,

EN 55022, EN 61000-3-2, EN 61000-3-3, EN 55024, AS/NZS CISPR 22, VCCI V-3.

Operating Temperature: 0°C to 50°C (32°F to 122°F)

Storage Temperature: -40°C to 70°C (-40°F to 158°F)

Operating Relative Humidity: 5% to 95% (non-condensing)

Notice

Safety Compliance

Warning: Fiber Optic Port Safety

When using a fiber optic media expansion module, never look at the

transmit laser while it is powered on. Also, never look directly at the fiber

TX port and fiber cable ends when they are powered on.

Avertissment: Ports pour fibres optiques - sécurité sur le plan optique

Ne regardez jamais le laser tant qu’il est sous tension. Ne regardez jamais

directement le port TX (Transmission) à fibres optiques et les embouts de

câbles à fibres optiques tant qu'ils sont sous tension.

Warnhinweis: Faseroptikanschlüsse - Optische Sicherheit

Niemals ein Übertragungslaser betrachten, während dieses eingeschaltet

ist. Niemals direkt auf den Faser-TX-Anschluß und auf die

Faserkabelenden schauen, während diese eingeschaltet sind.

Safety Information

Class 1 Laser Transceivers

Laser Radiation and Connectors

When the connector is in place, all laser radiation remains within the fiber. The maximum

amount of radiant power exiting the fiber (under normal conditions) is -12.6 dBm or

55 x 10-6 watts.

Removing the optical connector from the transceiver allows laser radiation to emit directly from

the optical port. The maximum radiance from the optical port (under worst case conditions) is

0.8 W cm-2 or 8 x 103W m2sr-1.

Do not use optical instruments to view the laser output. The use of optical instruments to

view laser output increases eye hazard. When viewing the output optical port, power must

be removed from the network adapter.

CLASS I

LASER DEVICE

DISPOSITIF LASER

DE CLASSE I

LASERGER

DER KLASSE I

ÄT

Notice

Please read the following safety information carefully before installing the

switch:

WARNING: Installation and removal of the unit must be carried out by qualified personnel

only.

• This guide is intended for use by network administrators who are responsible for setting up

and installing network equipment; consequently it assumes a basic working knowledge of

LANs (Local Area Networks).

• The unit must be connected to an earthed (grounded) outlet to comply with international

safety standards.

• Do not connect the unit to an A.C. outlet (power supply) without an earth (ground)

connection.

• The appliance coupler (the connector to the unit and not the wall plug) must have a

configuration for mating with an EN 60320/IEC 320 appliance inlet.

• The socket outlet must be near to the unit and easily accessible. You can only remove power

from the unit by disconnecting the power cord from the outlet.

• This unit operates under SELV (Safety Extra Low Voltage) conditions according to

IEC 60950. The conditions are only maintained if the equipment to which it is connected also

operates under SELV conditions.

France and Peru only

This unit cannot be powered from IT†supplies. If your supplies are of IT type, this unit must be

labelled Neutral, connected directly to earth (ground).

†Impédance à la terre

Power Cord Set

U.S.A. and Canada The cord set must be UL-approved and CSA certified.

The minimum specifications for the flexible cord are:

- No. 18 AWG - not longer than 2 meters, or 16 AWG.

- Type SV or SJ

- 3-conductor

The cord set must have a rated current capacity of at least 10 A.

The attachment plug must be an earth-grounding type with NEMA 5-15P

(15 A, 125 V) or NEMA 6-15P (15 A, 250 V) configuration.

Denmark The supply plug must comply with Section 107-2-D1, Standard DK2-1a

or DK2-5a.

Switzerland The supply plug must comply with SEV/ASE 1011.

Notice

Veuillez lire à fond l'information de la sécurité suivante avant d'installer le

Switch:

AVERTISSEMENT: L’installation et la dépose de ce groupe doivent être confiés à un

personnel qualifié.

• Ne branchez pas votre appareil sur une prise secteur (alimentation électrique) lorsqu'il n'y a

pas de connexion de mise à la terre (mise à la masse).

• Vous devez raccorder ce groupe à une sortie mise à la terre (mise à la masse) afin de respecter

les normes internationales de sécurité.

• Le coupleur d’appareil (le connecteur du groupe et non pas la prise murale) doit respecter une

configuration qui permet un branchement sur une entrée d’appareil EN 60320/IEC 320.

• La prise secteur doit se trouver à proximité de l’appareil et son accès doit être facile. Vous ne

pouvez mettre l’appareil hors circuit qu’en débranchant son cordon électrique au niveau de

cette prise.

• L’appareil fonctionne à une tension extrêmement basse de sécurité qui est conforme à la

norme IEC 60950. Ces conditions ne sont maintenues que si l’équipement auquel il est

raccordé fonctionne dans les mêmes conditions.

France et Pérou uniquement:

Ce groupe ne peut pas être alimenté par un dispositif à impédance à la terre. Si vos alimentations sont

du type impédance à la terre, ce groupe doit être alimenté par une tension de 230 V (2 P+T) par le

biais d’un transformateur d’isolement à rapport 1:1, avec un point secondaire de connexion portant

l’appellation Neutre et avec raccordement direct à la terre (masse).

U.K. The supply plug must comply with BS1363 (3-pin 13 A) and be fitted with

a 5 A fuse which complies with BS1362.

The mains cord must be <HAR> or <BASEC> marked and be of type

HO3VVF3GO.75 (minimum).

Europe The supply plug must comply with CEE7/7 (“SCHUKO”).

The mains cord must be <HAR> or <BASEC> marked and be of type

HO3VVF3GO.75 (minimum).

IEC-320 receptacle.

Power Cord Set

Notice

vii

Bitte unbedingt vor dem Einbauen des Switches die folgenden Sicherheitsan-

weisungen durchlesen:

WARNUNG: Die Installation und der Ausbau des Geräts darf nur durch Fachpersonal

erfolgen.

• Diese Anleitung ist fr die Benutzung durch Netzwerkadministratoren vorgesehen, die fr die

Installation und das einstellen von Netzwerkkomponenten verantwortlich sind; sie setzt

Erfahrung bei der Arbeit mit LANs (Local Area Networks) voraus.

• Das Gerät sollte nicht an eine ungeerdete Wechselstromsteckdose angeschlossen werden.

• Das Gerät muß an eine geerdete Steckdose angeschlossen werden, welche die internationalen

Sicherheitsnormen erfüllt.

• Der Gerätestecker (der Anschluß an das Gerät, nicht der Wandsteckdosenstecker) muß einen

gemäß EN 60320/IEC 320 konfigurierten Geräteeingang haben.

• Die Netzsteckdose muß in der Nähe des Geräts und leicht zugänglich sein. Die

Stromversorgung des Geräts kann nur durch Herausziehen des Gerätenetzkabels aus der

Netzsteckdose unterbrochen werden.

• Der Betrieb dieses Geräts erfolgt unter den SELV-Bedingungen

(Sicherheitskleinstspannung) gemäß IEC 60950. Diese Bedingungen sind nur gegeben, wenn

auch die an das Gerät angeschlossenen Geräte unter SELV-Bedingungen betrieben werden

Cordon électrique - Il doit être agréé dans le pays d’utilisation

Etats-Unis et Canada: Le cordon doit avoir reçu l’homologation des UL et un certificat de la

CSA.

Les spe'cifications minimales pour un cable flexible sont AWG No. 18,

ouAWG No. 16 pour un cable de longueur infe'rieure a` 2 me'tres.

- type SV ou SJ

- 3 conducteurs

Le cordon doit être en mesure d’acheminer un courant nominal d’au

moins 10 A.

La prise femelle de branchement doit être du type à mise à la terre (mise

à la masse) et respecter la configuration NEMA 5-15P (15 A, 125 V) ou

NEMA 6-15P (15 A, 250 V).

Danemark: La prise mâle d’alimentation doit respecter la section 107-2 D1 de la

norme DK2 1a ou DK2 5a.

Suisse: La prise mâle d’alimentation doit respecter la norme SEV/ASE 1011.

Europe La prise secteur doit être conforme aux normes CEE 7/7 (“SCHUKO”)

LE cordon secteur doit porter la mention <HAR> ou <BASEC> et doit

être de type HO3VVF3GO.75 (minimum).

Notice

viii

Stromkabel. Dies muss von dem Land, in dem es benutzt wird geprüft werden:

Schweiz Dieser Stromstecker muß die SEV/ASE 1011Bestimmungen einhalten.

Europe Das Netzkabel muß vom Typ HO3VVF3GO.75 (Mindestanforderung)

sein und die Aufschrift <HAR> oder <BASEC> tragen.

Der Netzstecker muß die Norm CEE 7/7 erfüllen (”SCHUKO”).

Other manuals for Matrix-V V2H124-24FX

Table of contents

Other Enterasys Switch manuals

Enterasys

Enterasys SmartSwitch 2200 Operation manual

Enterasys

Enterasys Vertical Horizon VH-2402-L3 User manual

Enterasys

Enterasys Matrix 7H4385-49 Manual

Enterasys

Enterasys Matrix E1 1G694-13 User manual

Enterasys

Enterasys SecureStack C2 C2G124-24 Manual

Enterasys

Enterasys Enterasys SecureStack B2 B2G124-24 Manual

Enterasys

Enterasys Matrix 7H4382-49 User manual

Enterasys

Enterasys Vertical Horizon VHIM100-S2MFX 100BASE FX-SC User manual

Enterasys

Enterasys S Series Manual

Enterasys

Enterasys SmartSwitch 6G302-06 User manual

Enterasys

Enterasys Matrix E1 1H582-51 Quick start guide

Enterasys

Enterasys SecureStack B3G124-24 User manual

Enterasys

Enterasys 6H308-48 Manual

Enterasys

Enterasys MicroMMAC-T User manual

Enterasys

Enterasys SmartSTACK EPIM1000-S1SX 1000BASE SX-SC User manual

Enterasys

Enterasys Matrix 7H4284-49 Manual

Enterasys

Enterasys SecureStack B2H124-48 User manual

Enterasys

Enterasys SmartSwitch 2200 Series 2E253 User manual

Enterasys

Enterasys D-Series Instruction Manual

Enterasys

Enterasys Enterasys Gold Distributed Forwarding Engine... Manual

Enterasys

Enterasys A4H124-24 Manual

Enterasys

Enterasys RoamAbout RBT-8200 User manual

Enterasys

Enterasys Matrix E1 1H582-25 User manual

Enterasys

Enterasys SmartSwitch 6000 User manual

Popular Switch manuals by other brands

URC

URC Total Control MFS-8 installation manual

Azbil

Azbil HPQ-D11 user manual

Sony

Sony DFS-900M operating instructions

SICK

SICK i17S operating instructions

F&F

F&F SZR-277 quick start guide

Shure

Shure UAMS/BK user guide

Dräger

Dräger X-zone Switch Off Instructions for use

Asco

Asco Joucomatic 349 Series manual

BT Mini Hub user guide

D-Link

D-Link DES-1226G manual

Johnson Controls

Johnson Controls FS80-C installation instructions

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Configuration guide

MicroNet

MicroNet SP1200A user manual

Ruijie

Ruijie RG-PF2920 Series Hardware installation and reference guide

Altinex

Altinex DA1914SX user guide

MiLAN

MiLAN MIL-SM2401M user guide

RJM

RJM MASTERMIND PBC/6X user manual

Atlas

Atlas MMK-KVM8 owner's manual